Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/3ZVNEHEUEQK76S5ZPSGCVQAZYDXFSU2R/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "[email protected]",
    "message_id_hash": "3ZVNEHEUEQK76S5ZPSGCVQAZYDXFSU2R",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/LSFS2H6LWJPEEIMYW3THQPUFSXE22MWN/?format=api",
    "sender": {
        "address": "vu3tyg (a) yahoo.co.in",
        "mailman_id": "ffb9caab06b3489aa9d16edd32c0d3b9",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/ffb9caab06b3489aa9d16edd32c0d3b9/emails/?format=api"
    },
    "sender_name": "Nitin Muttin",
    "subject": "Re: [amsat-bb] Signalink usb and UISS for 9600 baud packet",
    "date": "2018-10-08T17:17:46Z",
    "parent": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/L4GMJT6Y75PZL4N2OX3AMSGMELYSO3XU/?format=api",
    "children": [],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "I used to have a Icom 821H wired with signalink USB to the data port on the radio (radio set at 9.6K baud)  and worked fine for Winlink .\n73\nNitin [VU3TYG] \n\n    On Sunday, 7 October, 2018, 11:12:57 PM IST, Scott <[email protected]> wrote:  \n \n Hey Jack!\n\n9600 baud packet requires something in the area of 15k of audio bandwidth\nto work properly.  While I've heard from some folks that they've been able\nto operate 9600 with a Signalink, here is the spec. from Signalink's\nwebsite:\n\n------\nAudio Freq Response: Approx. 300Hz - 3.3Khz @ 600 ohms\n------\n\n... so, as you can see it's perfectly suited for thinks like 1200 baud\npacket or anything else that uses the traditional voice range up to 3k\n(audio), but it's just not the \"right tool\" for 9600.\n\nThe other factor is the radio - for anyone else reading this, please be\nsure to use a radio with a 9600-capable DATA port.  For the same reason\nthat the Signalink's audio bandwidth hampers operation at 9600 baud, on the\nradio end of the connection you need a DATA port that works above the 3k\naudio range.\n\nYour computer's sound card might be fine but if you'd like to have a\ndedicated sound device for interface to your radio's DATA port, I've had\ngreat luck with this item:\n\nhttps://www.amazon.com/gp/product/B003Y5D776\n\n73!\n\n-Scott,  K4KDR\n\n==============================================\n\nOn Sun, Oct 7, 2018 at 1:21 PM alex weimer <[email protected]> wrote:\n\n> I am running an Icom IC821H transceiver and the Signalink usb along with\n> UISS software running the UX7HO High speed packet modem. However I can't\n> seem to get this system to decode 9600 baud packet on falconsat-3 or  Elfin\n> A or B satellites. Is anyone using this combination to decode or send\n> packets through the Falconsat-3 digipeater on 9600 baud ??  I have tried\n> varied jumper wire settings on the Signalink and can send and decode 1200\n> baud packet with no problem. When trying 9600 baud the radio is set for\n> 9600 baud using SET Mode but it still will not decode 9600 baud packets..\n> Anybody out there have an answer ?? Thanks  JACK  KC7MG\n>\n_______________________________________________\nSent via [email protected]. AMSAT-NA makes this open forum available\nto all interested persons worldwide without requiring membership. Opinions expressed\nare solely those of the author, and do not reflect the official views of AMSAT-NA.\nNot an AMSAT-NA member? Join now to support the amateur satellite program!\nSubscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb\n  \n",
    "attachments": []
}