Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/C5INSMHF2J44Y3AGXBQQJUVNBBRRVR3I/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "000901c770d8$6a827590$6501a8c0@W5YI",
    "message_id_hash": "C5INSMHF2J44Y3AGXBQQJUVNBBRRVR3I",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/2IC6TN636PNBSHFEKEMNGUFUCQG4BXX5/?format=api",
    "sender": {
        "address": "snyderb (a) cox.net",
        "mailman_id": null,
        "emails": null
    },
    "sender_name": "Bruce",
    "subject": "[amsat-bb] Re: TNC settings for Kenwood TM-D700",
    "date": "2007-03-28T01:28:40Z",
    "parent": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/ZE6IHCNVFTRAYJ5DRKHYVD6GLMPFYE6O/?format=api",
    "children": [
        "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/BIZGI3XTT2QTMDTUY4OXH2CGNUW43LIN/?format=api"
    ],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "Jordan / rich\n\n    I just received my TM-D700A also & followed your cable instructions. \nWhen I powered up my 700A I get the following data;\nTASCO Radio Modem\nAX.25 Level 2 Version 2.0\nRelease 03/Dec/99 3Chip ver 1.08\nChecksum $04\ncmd:DA 070327210135\ncmd:\n\n  Trouble is now it won't accept data when I try to type in the commands. \nHave you guys been successful in inputting data from the keyboard.\n\n73 Bruce KG4YEV\n\n\n\n\n\n----- Original Message ----- \nFrom: <[email protected]>\nTo: \"Jordan Woolley\" <[email protected]>\nCc: <[email protected]>\nSent: Tuesday, March 27, 2007 12:26 PM\nSubject: [amsat-bb] Re: TNC settings for Kenwood TM-D700\n\n\n>\n> Hi Jordan!\n>\n> Make sure you're using a straight through serial cable (2-2, 3-3, etc).\n>\n> Then, confirm that the PC and D700 are using the same parameters:  9600\n> baud, No parity, 8 data bits, 1 stop bit and hardware flow control.  If\n> your settings aren't the same as this, make sure both the PC and D700\n> agree.\n>\n>>From non-TNC operations, press and hold F for 1 sec and then press the\n> TNC soft button.  Do this twice.  The D700 display should have TNC PKT in\n> the upper left.\n>\n> If the display shows TNC APRS, you just have to press and hold F for 1 sec\n> and TNC once.\n>\n> Hit CTRL-C to return to a cmd prompt if you're stuck in converse mode (you\n> shouldn't be since you just put the D700 into TNC PKT mode).\n>\n> At this point, you should be communicating with the D700 at the cmd\n> prompt.\n>\n> Check out the Kenwood Specialized Communications Manual:\n>\n> http://inform2.kenwoodusa.com/Manuals%5CTM-D700A%20Specialized.pdf\n>\n> Good luck!\n>\n> 73 de Rich N3WWN (FN00fh)\n>\n> On Tue, 27 Mar 2007, Jordan Woolley wrote:\n>\n>> Hi all,\n>>\n>>\n>> Was just wondering if there is anyone out there with any experience \n>> setting up a D700 for Packet operation. I do not seem to be able to get \n>> my terminal program to speak to the TNC. I can't even get a cmd prompt or \n>> any semblance of a connection. It seems to be physically connected fine \n>> but still no luck. I have set the baud rate for the port to match the TNC \n>> (9600) but am not having any luck. I am just using HyperTerminal. Any \n>> ideas?\n>>\n>>\n>> Thanks\n>> Jordan\n>>\n>> VK2HCA\n>> _______________________________________________\n>> Sent via [email protected]. Opinions expressed are those of the author.\n>> Not an AMSAT-NA member? Join now to support the amateur satellite \n>> program!\n>> Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb\n>>\n> _______________________________________________\n> Sent via [email protected]. Opinions expressed are those of the author.\n> Not an AMSAT-NA member? Join now to support the amateur satellite program!\n> Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb \n\n",
    "attachments": []
}