Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/DTPRRTZTE24HMWJEZ3NSFEXLM3W7XTKZ/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "CAK9b=digM0pgc8eyi=40EOc07qZ5PnmLucVB+72ESD3J=-vBJw@mail.gmail.com",
    "message_id_hash": "DTPRRTZTE24HMWJEZ3NSFEXLM3W7XTKZ",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/DTPRRTZTE24HMWJEZ3NSFEXLM3W7XTKZ/?format=api",
    "sender": {
        "address": "llryan807 (a) gmail.com",
        "mailman_id": "0a7d27f4ae6f453bbac45c8f738a4e86",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/0a7d27f4ae6f453bbac45c8f738a4e86/emails/?format=api"
    },
    "sender_name": "Larry Ryan",
    "subject": "[amsat-bb] SatPC32 with dual radios",
    "date": "2014-08-01T18:20:50Z",
    "parent": null,
    "children": [
        "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/OXY3MG5K5LTYI2IBE3MYRRKW3RAADWQ5/?format=api"
    ],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "I am trying to set up SatPC32 ver 12.8c \"unregistered\" with two FT-817s. My\nproblem is that there is no CAT control on radio 1. Radio 2 works\nperfectly. Here is the setup:\nRadio 1, com port 2, delay 70 (tried 110 also)\nRadio 2, com port 5\nChecked Atom. RX/TX change only (no other boxes checked but tried the\nothers)\nAs I change from sat to sat, Radio 2 will change freq and be steered but\nthere is no response from Radio 1\nIf I remove Radio 2 (unplug the USB cable) and configure only a radio 1,\nthere is no CAT control of radio 1.\nComputer is an HP Mini running Win7\nWatching Device Manager, I can unplug either USB cable and see port 2 or\nport 5 come and go as I plug and unplug.\n\nI have switched radios then switched the CAT USB cables (they are FTDI).\nStill radio 1 does not change.\n\nLeaving the radios plugged in to the same computer, I exited SatPC32 and\nstarted HRD and tested for CAT operation on each radio one at a time and\nthey both work.\n\nMy question: Why no CAT for radio 1? Why no error message? Are there any\nother troubleshooting steps I can take?\n\nI have searched just about everywhere on-line and see no one else having\nthis problem. I have found that many have success with the dual non-duplex\ntransceivers configuration.\n\nAny help would be appreciated.\nThanks, Larry W7DGP\n",
    "attachments": []
}