Email Detail
Show an email
GET /hyperkitty/api/list/[email protected]/email/ED574GODELZFQUTUP5KAZKL4DYMN5LUM/?format=api
{ "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/ED574GODELZFQUTUP5KAZKL4DYMN5LUM/?format=api", "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api", "message_id": "[email protected]", "message_id_hash": "ED574GODELZFQUTUP5KAZKL4DYMN5LUM", "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/WILUVB5IZPC7JGENH4TFGI6OQQXO5BS7/?format=api", "sender": { "address": "DCFox (a) rwglaw.com", "mailman_id": "2b2adad2573e49ecb6641ab539c7d05c", "emails": "https://mailman.amsat.org/hyperkitty/api/sender/2b2adad2573e49ecb6641ab539c7d05c/emails/?format=api" }, "sender_name": "D. Craig Fox", "subject": "Re: [amsat-bb] FoxDelta ST2-0417 USB setup help", "date": "2020-07-09T20:20:51Z", "parent": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/WILUVB5IZPC7JGENH4TFGI6OQQXO5BS7/?format=api", "children": [], "votes": { "likes": 0, "dislikes": 0, "status": "neutral" }, "content": "Jim, I use SATPC with a serial/usb adapter so cannot speak to your specific set up. However, I recently set up my FoxDelta (serial) for full az/el and noting worked. It really stumped me until I realized I neglected to match the FD 9600 baud rate with the associated SATPC server baud rate. Once I corrected that, all worked as it should. So be sure baud rate is correctly set.\r\n\r\n73, Craig\r\nN6RSX \r\n\r\n-----Original Message-----\r\nFrom: AMSAT-BB <[email protected]> On Behalf Of Jim Walls via AMSAT-BB\r\nSent: Wednesday, July 8, 2020 7:21 PM\r\nTo: Amsat-BB <[email protected]>\r\nSubject: [amsat-bb] FoxDelta ST2-0417 USB setup help\r\n\r\nI recently bought a FoxDelta ST2-0417 USB rotor interface for my Yaesu\r\nG-5500 rotor. I have the ST-2 communicating with the rotor just fine. I can see the azimuth and elevation readout and using the ST2 pushbuttons, I can control both just fine. However, I can't get it to communicate properly with my computer. I am running a Dell desktop under Windows 10 and have installed the CH360G driver. The ST2 shows as\r\nCOM8 according the the device manager. If I unplug the USB cable, the Device Manager confirms that COM8 goes away and when I plug the cable back in, COM8 returns. I initially was trying to use Nova for Windows (which I have used for 20+ years). I tried every software interface setting (using COM8) and the best I could get a couple weeks ago was Azimuth display and control (no elevation display, but it appeared that it tried to control elevation), but can't manage to replicate that today. Everything shows either 0.0 / 0.0 or ---- / ---- for the rotor pointing in Nova.\r\nSomewhat out of desperation, I downloaded SatPC32 and can't even get that far. As far as I can tell, every rotor type is expecting a parallel port interface. Keep in mind that I have never seen SatPC32 until an hour ago, so that may be my issue.\r\n\r\nMy preference would be to use Nova for Windows, but if that can't be made to work, I CAN switch over to SatPC32. In either case, the software will be used exclusively for rotor control and not doppler correction (not using a radio that supports that).\r\n\r\n\r\nDo you have any suggestions?\r\n\r\n--\r\n73\r\n-------------------------------------\r\nJim Walls - K6CCC\r\[email protected]\r\nOfc: 818-548-4804\r\nhttp://members.dslextreme.com/users/k6ccc/\r\nAMSAT Member 32537 - WSWSS Member 395\r\n\r\n_______________________________________________\r\nSent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA.\r\nNot an AMSAT-NA member? Join now to support the amateur satellite program!\r\nSubscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb\r\n\r\n\r\n(If this message is spam, please report it to IT Dept. Thank you.)\r\n", "attachments": [] }