Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/FSDN4JGNJXCOZ6C55OLSR2XGYEDRLQTY/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "009f01cc48b4$35f4a380$a1ddea80$@net",
    "message_id_hash": "FSDN4JGNJXCOZ6C55OLSR2XGYEDRLQTY",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/FSDN4JGNJXCOZ6C55OLSR2XGYEDRLQTY/?format=api",
    "sender": {
        "address": "kb2m (a) comcast.net",
        "mailman_id": "4f01ae6749a54d178a501e4efec2da0b",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/4f01ae6749a54d178a501e4efec2da0b/emails/?format=api"
    },
    "sender_name": "Jeff KB2M",
    "subject": "[amsat-bb]  5500 rotor problem",
    "date": "2011-07-22T21:13:23Z",
    "parent": null,
    "children": [],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "\nThanks for all the replies on my 5500 rotor problem! I had some time tonite\nto work on it and here's what I got. On both a1 a3, and e1 e3 pairs I'm\nreading only 1.0 volts. Between a2 a3 , and e2 e3 pairs I see only .5 volts\nat half range, IE an elevation of 90 degrees =  a reading of .5 volts. I'm\ngoing to order a new Q2 UA7806C and this should do it. Only question I have\nis why Q2 failed to only output 1 volt, don't they usually fail and output 0\nvolts? I'm thinking it might be something else in the circuit feeding power\nto Q2. If so I will work this further when I actually take the rotor box\napart with the new Q2 in hand. One other thing, I wish I can find all my\ncomponents' I boxed up when I moved. I bet I have 10 of these in stock :)\nThanks again for all the help guys, the electronic copy of the manual was a\nbig help as I can't find my copy....\n\n \n\n73 Jeff kb2m \n\n \n\n  \n\n> I'm having a problem with my 5500 after a thunderstorm. What is \n\n> happening is that the rotor works manually, but doesn't display az and \n\n> el\n\ninformation\n\n> on the control box. Also when I try to use computer control it goes \n\n> all\n\nthe\n\n> way to stop in both azimuth and elevation. I'm thinking this might be \n\n> in\n\nthe\n\n> control box, as both az and el are doing the same thing, the control \n\n> box being the single point of failure. Did anyone ever have this \n\n> problem? How can I diagnosis what chip might be at fault without a \n\n> schematic. I vaguely remember having this same problem after a close  \n\n> lightning strike with my prior az el Yaesu box about 14 years ago but \n\n> don't remember what chip I swapped out, or how I determined which one \n\n> was at fault. This getting old thing really sucks. Any help would be\nappreciated.\n\n> \n\n> 73 Jeff kb2m\n\n \n\n\n",
    "attachments": []
}