Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/H6RJC6TTY4XCE5N4D4GGQ3RXSW4MOLJ7/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "[email protected]",
    "message_id_hash": "H6RJC6TTY4XCE5N4D4GGQ3RXSW4MOLJ7",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/H6RJC6TTY4XCE5N4D4GGQ3RXSW4MOLJ7/?format=api",
    "sender": {
        "address": "k.swaggart (a) charter.net",
        "mailman_id": "b53f0c8256f444dea314ac1412cd4bd5",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/b53f0c8256f444dea314ac1412cd4bd5/emails/?format=api"
    },
    "sender_name": "[email protected]",
    "subject": "Re: [amsat-bb] G-5500 az rotor failure",
    "date": "2019-08-23T23:49:28Z",
    "parent": null,
    "children": [
        "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/GLEDAYHQ6FL5A27V4LWW54WPMQ3EV3AN/?format=api"
    ],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "The problem turned out to be a loose setscrew at the motor. Easy fix, but\ntook about four hours to reassemble the rotor so the limit switch was\ntripped correctly and then get the antennas reattached. Anyway, back in\nbusiness.\n\n \n\nI took quite a few photos of the az rotor disassembly and I'll add them to\nmy G5500 page within the next few days:\n\nhttp://www.ocrg.org/W7KKE/rotor/rotor.html\n\n \n\n73,\n\nKen, W7KKE\n\n \n\nFrom: [email protected] <[email protected]> \nSent: Friday, August 23, 2019 10:39\nTo: AMSAT-BB ([email protected]) <[email protected]>\nSubject: G-5500 az rotor failure\n\n \n\nThis morning I found my G-5500 will not move left or right. Not even a\nwiggle. Took some measurements and the wiring appears to be intact but I\ndon't understand the 40 Vac readings when the rotor is connected to the\ncontrol box. Here are my readings taken at the control box end of the\nwiring:\n\n \n\nRotor connected to control box:\n\nCommon (pin 6) to Left (pin 4)  Press Left: 28 Vac  Right: 40 Vac\n\nCommon (pin 6) to Right (pin 5) Press Left: 40 Vac  Right: 28 Vac\n\n \n\nRotor disconnected. Measuring control box terminals:\n\nPin 6 to 4  Press Left: 29.5 Vac  Press right: 0\n\nPin 6 to 5 Press Left: 0  Press Right: 29.5 Vac\n\n \n\nMeasuring rotor cable at control box, disconnected from box:\n\n6 (brown) to 4 (blue) 5.3 Ohms\n\n6 (brown) to 5 (orange) 5.3 Ohms\n\n4 (blue) to 5 (orange) 8.9 Ohms\n\n \n\nAny suggestions before I pull the rotor off the mast?\n\n \n\n73,\n\nKen, W7KKE\n\n \n\n \n\n \n\n",
    "attachments": []
}