Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/HTC6F4NNYHHHGPAVONLE2KN6XTD4EWP4/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "[email protected]",
    "message_id_hash": "HTC6F4NNYHHHGPAVONLE2KN6XTD4EWP4",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/M553BVAAYVQZOYX27H5JOINZE6OOYUJD/?format=api",
    "sender": {
        "address": "vu3tyg (a) yahoo.co.in",
        "mailman_id": "ffb9caab06b3489aa9d16edd32c0d3b9",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/ffb9caab06b3489aa9d16edd32c0d3b9/emails/?format=api"
    },
    "sender_name": "Nitin Muttin",
    "subject": "Re: [amsat-bb] Receiving TigriSat Satellite",
    "date": "2014-07-18T15:41:53Z",
    "parent": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/M553BVAAYVQZOYX27H5JOINZE6OOYUJD/?format=api",
    "children": [],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "Rupesh,\n\nI suggest setup the TS 2000 TNC in AGWPE and OnlineKISS will connect to the port in AGWPE to enable decode. Other way is to use a software TNC http://uz7.ho.ua/packetradio.htm to which Online KISS will connect to decode the data.\n \n73\nNitin [VU3TYG]\n\n\n>________________________________\n> From: Rupesh Lad <[email protected]>\n>To: [email protected] \n>Sent: Friday, 18 July 2014 8:59 PM\n>Subject: [amsat-bb] Receiving TigriSat Satellite\n> \n>\n>Hello all,\n>\n>I am trying to receive TigriSat, First Iraqi satellite which have a FSK\n>Beacon on 435MHz frequency. I use a 2 unit array of cross Yagi antenna and\n>Kenwood TS2000 TRX.\n>\n>The packet sounds quite good on TS2k whereas nothing is decoded on\n>OnlineKISS+ ver 8.2.2 by DK3WN. The COMM port is connected to the serial\n>port of TRX. The internal TNC of TS2000 was set to KISS mode. On air baud\n>rate 9k6 and COMM port baud rate to 9k6 as expected. The COMM port also\n>goes green on the software screen.\n>\n>Have I miss any setting or is anything else required to decode the signals?\n>\n>-- \n>Regards,\n>Rupesh Lad\n>_______________________________________________\n>Sent via [email protected]. Opinions expressed are those of the author.\n>Not an AMSAT-NA member? Join now to support the amateur satellite program!\n>Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb\n>\n>\n>\n",
    "attachments": []
}