Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/IZRPLMLXIG6YQEKOJYYSMAFLSO6WS3RG/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "004301ca5bdc$27c7f8f0$0200a8c0@hop",
    "message_id_hash": "IZRPLMLXIG6YQEKOJYYSMAFLSO6WS3RG",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/65YL3VPDB4S7XXH3LQWY6B2O7RP76G4Y/?format=api",
    "sender": {
        "address": "larryg (a) amerion.com",
        "mailman_id": null,
        "emails": null
    },
    "sender_name": "Larry Gerhardstein",
    "subject": "[amsat-bb]  g-5500 gs-232b trouble",
    "date": "2009-11-02T16:47:22Z",
    "parent": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/65YL3VPDB4S7XXH3LQWY6B2O7RP76G4Y/?format=api",
    "children": [],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "\nI have a G-5500 and GS-232B being commanded from SatPC32.  These items \nused to work fine 5 months ago while I was using a temporary antenna set \nup.  Since then, I've been building a new permanent antenna system. \nNow, SatPC32 transceiver controls work, but not the rotor controls.\n\nThe G-5500 control box works fine as long is it's not connected into the \ncomputer via GS-232B.  I can run the antennas up and down and left and \nright and the meteres display the correct values.\n\nWhen I connect the GS-232B into the G-5500 using the supplied AZ/EL \ncable, the control box still works and displays correct Azimuth and \nElevation on the G-5500 meters.\n\nBut when I next connect the GS-232B into the serial port on the \ncomputer, the Azimuth meter suddenly goes to zero setting.  The \nElevation meter displays the correct value.  If I then disconnect the AZ \nhalf of the cable from the GS-232B, both meters display correctly.  This \nis true whether the power on the GS-232B is On or Off.\n\nThe GS-232B manual shows 10 wires going from the G-5500 to the GS-232B \nAZ/EL connectors on the pin-out diagram.  My cable has only 7 wires \ntotal.  What's with that?\n\nIn any case, computer control of the G-5500 from SatPC32 is not working.\n\nI'm wondering if I may have fried the GS-232B.  Right now, I'm letting \nSatPC32 control the rig and I'm manually adjusting the AZ/EL rotors to \nvalues SatPC32 has displayed; it's tricky.\n\nAny help in troubleshooting this system will be greatly appreciated. \nLater today, I will make certain that the computer serial port is still \nworking.\n\n73, Larry W7IN, Plains, Montana DN27.\n\n",
    "attachments": []
}