Email Detail
Show an email
GET /hyperkitty/api/list/[email protected]/email/LG46ILJN5W6Z5XHMW4FF4U2WHK5YXEYL/?format=api
{ "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/LG46ILJN5W6Z5XHMW4FF4U2WHK5YXEYL/?format=api", "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api", "message_id": "[email protected]", "message_id_hash": "LG46ILJN5W6Z5XHMW4FF4U2WHK5YXEYL", "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/TQB3YU32NGAHE525EZ6TSSU3LPZKXROX/?format=api", "sender": { "address": "DCFox (a) rwglaw.com", "mailman_id": "2b2adad2573e49ecb6641ab539c7d05c", "emails": "https://mailman.amsat.org/hyperkitty/api/sender/2b2adad2573e49ecb6641ab539c7d05c/emails/?format=api" }, "sender_name": "D. Craig Fox", "subject": "Re: [amsat-bb] unable to dig over ISS", "date": "2020-05-20T17:01:19Z", "parent": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/DJHQ3X5JECETG3S4YIKRXJQWN2INIKNA/?format=api", "children": [], "votes": { "likes": 0, "dislikes": 0, "status": "neutral" }, "content": "Thank you Scott and everyone else for offering suggestions. I always used ARISS but also tried RS0ISS as it used to work as well. None of the obvious stuff has helped.\n\n73,\nCraig\nN6RSX \n\n-----Original Message-----\nFrom: AMSAT-BB <[email protected]> On Behalf Of Scott via AMSAT-BB\nSent: Tuesday, May 19, 2020 2:08 PM\nCc: [email protected]\nSubject: Re: [amsat-bb] unable to dig over ISS\n\nTo \"CQ\" via \"ARISS\" continues to work very well for the ISS digipeater.\n\n73!\n\n-Scott, K4KDR\n\n===================\n\nOn Tue, May 19, 2020 at 2:05 PM D. Craig Fox via AMSAT-BB < [email protected]> wrote:\n\n> Thanks Bob. Not sure but I seem to recall that sound modem has a tone \n> calibration function which may allow me to do as you suggest. I have \n> regularly tried RS0ISS. Both ARISS and RS0ISS used to work fine for me.\n>\n> Craig\n> N6RSX\n>\n> -----Original Message-----\n> From: Robert Bruninga <[email protected]>\n> Sent: Tuesday, May 19, 2020 10:55 AM\n> To: D. Craig Fox <[email protected]>\n> Cc: [email protected]\n> Subject: RE: [amsat-bb] unable to dig over ISS\n>\n> A series capacitor (experimental value until you hear the change in \n> pitch on another radio) will boost the high tone. A parallel cap to \n> ground (experimental value) can reduce the high tone...\n>\n> ARISS reports that the ericcson radio on ISS is quite deaf and so \n> needs to hear some power. Also, they are not sure if the ARISS alias \n> works. Try RS0ISS.\n>\n> Bob\n> bob\n>\n> -----Original Message-----\n> From: D. Craig Fox <[email protected]>\n> Sent: Tuesday, May 19, 2020 1:20 PM\n> To: 'Robert Bruninga' <[email protected]>\n> Cc: [email protected]\n> Subject: RE: [amsat-bb] unable to dig over ISS\n>\n> Thanks Bob! Maybe that is the issue. Now I just need to figure out how \n> to analyze the tones being generated by my Signalink.\n>\n> Thank you and 73\n>\n> Craig\n> N6RSX\n>\n> -----Original Message-----\n> From: Robert Bruninga <[email protected]>\n> Sent: Tuesday, May 19, 2020 7:47 AM\n> To: D. Craig Fox <[email protected]>; amsat bb <[email protected]>\n> Subject: RE: [amsat-bb] unable to dig over ISS\n>\n> If the ISS radio is the Kenwood D700, it is quite sensitive to \n> unbalanced tones. So your base station might work well with a local \n> digi, but if the low tone is higher than the high tone by just a bit \n> (or other way around), it will not be decoded by the D700. This is \n> because the kenwood is optimized for flat tones (at the discriminator) \n> not pre-emphasized as most people do when they hook up an external TNC to the mic circuits.\n>\n> (I may have the tones reversed). One of them can be higher than the \n> other a bit and work fine. The other way around it simply will not work.\n> Bob\n>\n> -----Original Message-----\n> From: AMSAT-BB <[email protected]> On Behalf Of D. Craig Fox \n> via AMSAT-BB\n> Sent: Monday, May 18, 2020 6:18 PM\n> To: '[email protected]' <[email protected]>; [email protected]\n> Subject: Re: [amsat-bb] unable to dig over ISS\n>\n> Thanks Umesh. Well I would agree except that several nights ago I \n> pulled out the D7 HT and elk, and digipeated numerous times on a nigh pass.\n> Immediately went to the base station and tried but no dice. Plus, on \n> every pass Ive tried on my base station, I see the stations I decoded \n> show up on the ISS spotter. So it remains as issue at my end.\n>\n> Thank you\n>\n> Craig\n> N6RSX\n>\n> From: [email protected] <[email protected]>\n> Sent: Monday, May 18, 2020 2:22 PM\n> To: [email protected]; D. Craig Fox <[email protected]>\n> Subject: Re: [amsat-bb] unable to dig over ISS\n>\n> Looking at when the problem started, I'm assuming the problem is \n> related to ISS turning off their packet systems regularly.\n>\n> Long ago I was able to operate ISS packet throughout the pass, even \n> drop messages into their their BBS, etc., but for a considerable time \n> now I have pretty much given up working with ISS packet.\n>\n> All other factors considered, the fact that your system gets ACK-ed on\n> 144.390 is proof positive. It has always been a guarantee to be able \n> to work ISS packet.\n>\n> 73!\n> Umesh,k6vug\n>\n>\n>\n>\n>\n> On Monday, May 18, 2020, 11:40:40 AM PDT, D. Craig Fox via AMSAT-BB < \n> [email protected]<mailto:[email protected]>> wrote:\n>\n>\n> Posting this as a last resort as I ordinarily enjoy doing my own \n> troubleshooting, but this one has me perplexed. For normal sat ops I \n> am running a TS2Kx, 5 el 2m and 11 el 70 cm Directive Systems yagis on a G5400.\n> Doppler and rotor all run by SatPc32. Up to about a year ago I ran \n> AGWPE and UISS and a USB Signalink (through ACC 2) to dig over ISS. \n> Never had a problem, except the occasional decode problem fixed by \n> UX7HO Soundmodem. I finally removed AGWPE and began using Sound Modem with UISS.\n> However, since then I have been unable to dig over ISS. I decode just \n> fine.\n> My transmissions sound like normal packet transmissions, listening on \n> a second receiver. I have used all of the online recommended settings \n> for both Sound Modem and UISS. I have played with the audio levels. I \n> substituted Signalinks in case that was the issue. Also, I have no \n> problem sending APRS over 144.39 using different \"wide\" settings and \n> getting an acknowledgement back. My \"neighbor\" Christy KB6LTY has \n> provided mu ch assistance, but still no joy. I am missing something. \n> So I'm hoping someone has had a similar issue with a similar set up \n> and can maybe send me screen shots of their settings that work, especially in Sound Modem.\n> Or, any other suggestions would be greatly appreciated.\n>\n> Thank you in advance\n>\n> Craig\n> N6RSX\n>\n_______________________________________________\nSent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA.\nNot an AMSAT-NA member? Join now to support the amateur satellite program!\nSubscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb\n\n\n(If this message is spam, please report it to IT Dept. Thank you.)\n", "attachments": [] }