Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/NHXB42OO6ZCMVIMXZEFGTRGGGMEFLIHY/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "CADDbS5Dvja0AwSB8Fiy4xXJLuKs6E5=fzV8ajOqhtkhoMLYF4A@mail.gmail.com",
    "message_id_hash": "NHXB42OO6ZCMVIMXZEFGTRGGGMEFLIHY",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/4NKBS3NGFRUUJKSDWGP4YDFBCCIZFUK5/?format=api",
    "sender": {
        "address": "k0jm.mark (a) gmail.com",
        "mailman_id": "4fa2bb5eca934ca4b14c4ede20ff0c9a",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/4fa2bb5eca934ca4b14c4ede20ff0c9a/emails/?format=api"
    },
    "sender_name": "Mark Johns, K0JM",
    "subject": "Re: [amsat-bb] SatPC32 - need help with configuration of\tDoppler.SQX file",
    "date": "2020-12-01T16:02:12Z",
    "parent": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/4NKBS3NGFRUUJKSDWGP4YDFBCCIZFUK5/?format=api",
    "children": [
        "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/KSRR65KQVHX6WMNU34FTU72SSGPO6MP5/?format=api"
    ],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "It may also help if you save the file with the correct name as\nDoppler.SQF rather than as Doppler.SQX\n--\nMark D. Johns, KØJM\nAMSAT Ambassador & News Service Editor\nBrooklyn Park, MN USA   EN35hd\n-----------------------------------------------\n\"Heaven goes by favor; if it went by merit,\n   you would stay out and your dog would go in.\"\n    ---Mark Twain\n\nOn Tue, Dec 1, 2020 at 2:09 AM Bill Dzurilla via AMSAT-BB\n<[email protected]> wrote:\n>\n>  I was just advised that, contrary to the RS-44 line in the JE9PEL file, it should be REV rather than NOR. If so, that would explain a lot.\n> 73, Bill NZ5N\n>     On Monday, November 30, 2020, 02:10:53 PM EST, Bill Dzurilla <[email protected]> wrote:\n>\n>   Hello,\n> Does anyone have any tips for proper configuration of the Doppler.SQX file on SatPC32? I'm having a hard time getting it correct for RS-44.\n> I started with the standard line from JE9PEL: RS-44 (DOSAAF-85),435640,145965,USB,LSB,NOR,0,0,SSB\n> When I heard the sat, I started clicking the Uplink Calibration buttons in the CAT Control window until my voice sounded natural. It was pretty far off, something like 8800hz. To save, I clicked on Change/Store Data File and then clicked RX/TX Freq. Data. I thought this was all I needed to do, but on the next pass my TX and RX were again out of sync. On every pass, I need to start over, and each time the uplink frequency is several thousand hertz off. My current line is: RS-44 (DOSAAF-85),435631.85,145970.86,USB,LSB,NOR,0,0,SSB\n> What am I doing wrong?\n> Thanks and 73, Bill NZ5N\n> _______________________________________________\n> Sent via [email protected]. AMSAT-NA makes this open forum available\n> to all interested persons worldwide without requiring membership. Opinions expressed\n> are solely those of the author, and do not reflect the official views of AMSAT-NA.\n> Not an AMSAT-NA member? Join now to support the amateur satellite program!\n> Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb\n",
    "attachments": []
}