Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/PII2KBRMB3HK6TLZPFJIDC2YHET2EVSG/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "001501c93221$2a02b5a0$0200a8c0@Tanguray",
    "message_id_hash": "PII2KBRMB3HK6TLZPFJIDC2YHET2EVSG",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/JYLFJ3DCNKY67HVODWW5OKSVFIQRTKV3/?format=api",
    "sender": {
        "address": "rogerkola (a) aol.com",
        "mailman_id": "8323dbe496014835b5bd2be9b5ff6f66",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/8323dbe496014835b5bd2be9b5ff6f66/emails/?format=api"
    },
    "sender_name": "Roger Kolakowski",
    "subject": "[amsat-bb] Re: beginner question re: uplink power",
    "date": "2008-10-19T19:30:36Z",
    "parent": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/2WYHNFGYKMNQNIERYO6TWRROUQRBAUQT/?format=api",
    "children": [],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "I think I would contact Ramsey and see what the resistor selection\nlimitations are, unless you have a schematic and can determine it from the\ndesign.\n\nSure enough, if you set it for 10 watts you are going to, some day, put 50\nor 100 watts through it in error and I'm assuming if you kill the remote\nswitching it defaults to receive and therefore doesn't switch the preamp out\nresulting in a trip up the tower to fix 2 things.\n\nIf you set it for 100 watts, you will someday want to run less and again it\nwon't key. Same trip up the tower.\n\nHard wiring, as has been suggested, is your safest choice. As the switch has\nthe relay in it, maybe Ramsey can tell you where to tap in to directly\nswitch the sensor.\n\nNice choice of rig though ;-)\n\nRoger\nWA1KAT\n\n\n----- Original Message -----\nFrom: \"corner5\" <[email protected]>\nTo: \"Roger Kolakowski\" <[email protected]>\nCc: <[email protected]>\nSent: Sunday, October 19, 2008 1:42 PM\nSubject: [amsat-bb] Re: beginner question re: uplink power\n\n\n> Hi Roger,\n>\n> Thanks very much for the reply.  I did forget to mention that I will be\n> using my Kenwood TS2000 for this purpose.  This allows me the full 0-100\n> watts choice for 2m, and 0-50 watts choice for 70cm.  The preamps are\n> only for receive.  The RF switches are between the rig and the preamps\n> and will bypass the preamps upon transmit.  I can start out my RF out\n> anywhere within the above stated ranges.\n>\n> Any further thoughts?\n>\n> .paul\n>\n\n",
    "attachments": []
}