Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/PKKTW3XDA6NVFJI2ZT4C2IJZMBH562UF/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "[email protected]",
    "message_id_hash": "PKKTW3XDA6NVFJI2ZT4C2IJZMBH562UF",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/FEUTG6N33Y6XCZOE4HQRWJCWOGIISGLP/?format=api",
    "sender": {
        "address": "walterh (a) k5wh.net",
        "mailman_id": "269d35853c9e4103ad40904b3e996e31",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/269d35853c9e4103ad40904b3e996e31/emails/?format=api"
    },
    "sender_name": "[email protected]",
    "subject": "Re: [amsat-bb] SatPC32 and windows 10",
    "date": "2019-03-29T17:10:37Z",
    "parent": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/FEUTG6N33Y6XCZOE4HQRWJCWOGIISGLP/?format=api",
    "children": [],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "Did you notice this in the FAQ docs. As you really have to dig into it a bit to catch this critical step.\n\nI have a TS-2000x and it works just fine with this.\n\n\n\nKenwood TS-2000 CAT problem with SatPC32 vers. 12.8c and later\n\nWith SatPC32  and SatPC32ISS version 12.8c I use a new component to manage the serial ports. The old component supported only COM port numbers up to 15. The new USB-to-Serial adapters generate often virtual port numbers > 15, however.\n\nSteering  the TS-2000 with SatPC32 and SatPC32ISS vers. 12.8c  requires the option \"RTS+12V\" (SatPC32 menu \"Setup\" > \"Radio Setup\") to be checked.  That imitates the hardware handshaking the TS-2000 expects.  \n\n \n\nAnother solution is a homemade RS-232 cable with only the 3 lines Ground, RxD, TxD wired and a wire bridge between CTS and RTS (pins 7 and 8 of the DB-9 plug) on the TS-2000 side.   \n\n\nHope that helps,\nWalter/K5WH\n\n-----Original Message-----\nFrom: AMSAT-BB <[email protected]> On Behalf Of Mike\nSent: Thursday, March 28, 2019 8:02 PM\nTo: [email protected]\nSubject: [amsat-bb] SatPC32 and windows 10\n\nI was successfully using Windows 7 to run SatPC32 and suffered a catastrophic failure of the computer so I had to replace it.\n\nI replaced it with a used Windows 10 computer.\n\nI can install SatPC32 and get it set up, as best as i remember how to do.\nThings seem to be working except for the doppler tracking of the CAT control.\nI know SatPC is talking to my TS-2000 because it goes into satellite mode when I start SatPC.  Also, I can click on the CW tab and it changes to CW and back when I deselect it.  But no doppler tracking control.\n\nI'm at a loss as what to do at this point.\n\nThanks for any help.\n\nMike Stansberry, K0TER\n\n\n_______________________________________________\nSent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA.\nNot an AMSAT-NA member? Join now to support the amateur satellite program!\nSubscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb\n\n",
    "attachments": []
}