Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/QUYJHFPXUTZGEUKSIWC6OLF6CZAPWTVP/?format=api",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/?format=api",
    "message_id": "18587302.1364427.1262963358924.JavaMail.morsesat@mail.srv.lgcyny1.cv.net",
    "message_id_hash": "QUYJHFPXUTZGEUKSIWC6OLF6CZAPWTVP",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/QUYJHFPXUTZGEUKSIWC6OLF6CZAPWTVP/?format=api",
    "sender": {
        "address": "morsesat (a) optonline.net",
        "mailman_id": "72f51eafcada419487d1a984af73dff5",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/72f51eafcada419487d1a984af73dff5/emails/?format=api"
    },
    "sender_name": "DOMINICK INTERDONATO",
    "subject": "[amsat-bb] Re: IC 910H query",
    "date": "2010-01-08T15:09:18Z",
    "parent": null,
    "children": [],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "I agree with all you have suggested, Mark.  I too had questions about \npower output on the 910.  I discovered that the power to the radio was \nthe culprit.  Before you send it away, check and make sure you have #10 \ncables to the radio and your power supply delivers the correct voltage \nand current.  Mine does and it meets Specs on VHF and UHF on \"both\" my \n910's.\nOne I have the 1.2ghz Module in.  One I use for demos at field day and \nhamfests etc.\nGood luck.\n73, NB2F\n\nDee\n\n\nOn Fri, Jan 8, 2010 at 9:18 AM, Mark L. Hammond wrote:\n\n> Hi Louis,\n>\n> Congratulations on your new IC-910H!   I was the very lucky winner of\n> a new IC-910H at the AMSAT Symosium, so I have a bit of time on the\n> radio now.\n>\n> I haven't used RigTalk, so I can't comment on that.\n>\n> Regarding the CIV USB cable--my experience is that you do NOT need to\n> check the RTS + 12V option.   I bought a cheap USB CIV level converter\n> on eBay, and it works perfectly without this option checked.  My\n> homebrew interface, on the other hand, uses the serial port and\n> requires me to check that option, or else it doesn't receive power via\n> the serial line and won't work.\n>\n> You will need to know which serial port number the USB converter is\n> using/emulating; there is a setting in SatPC32 where you must tell it\n> the comport number where  the level converter (USB CIV cable) is\n> installed.  You can use the Windows Hardware Tab/Device Manager to\n> figure that out.\n>\n> Your addresses are correct for \"default\", they should work OK.  Be\n> sure to also set the BAUD rate in both SatPC32 and the radio to match.\n>  I think 9600 baud is the highest the radio will do.  Be sure to read\n> the \"Hints\" sections in the SatPC32 program to figure out an\n> appropriate delay setting, too.\n>\n> Lots of folks using this setup, so you should be able to get lots of\n> help as you get it going!  SatPC32 is a fantastic program for working\n> satellites.\n>\n> Personal question/note.  I am interested in the output power of your\n> IC-910H.   Mine is rather low on both VHF (75W) and UHF (45W).   So, I\n> just sent it back to Icom in hopes they can make it meet \"advertised\n> and published specs\" in that regard.   Shipping and insurance on that\n> radio was over $50!  I won't complain since I won the radio :)\n>\n> 73,\n>\n> Mark N8MH\n>\n> On Thu, Jan 7, 2010 at 4:24 PM, Louis House <[email protected]> \n> wrote:\n>> I plan to commission my new IC 910 H on Saturday this week.  I plan \n>> to drive the radio with the \"RigTalk\" and CIV cable from a USB port. \n>> Has anyone experienced any negative function from this data control \n>> system type??  In setting up the SatPC32 software, the addresses that \n>> appeared by default are \"$60\" (in all four boxes in the \"Radio Set \n>> Screen\").  Does this $60 setting work OK??  The read me file is not \n>> very clear concerning the selection for \"RTS + 12V\", does the IC 910 \n>> H need this setting selected to work correctly??    Any other known \n>> problems would also be most helpful.\n>> Thanks for listening.\n>> Louis, KD5GM\n>> CW ;-) The Original Digital\n>\n> _______________________________________________\n> Sent via [email protected]. Opinions expressed are those of the \n> author.\n> Not an AMSAT-NA member? Join now to support the amateur satellite \n> program!\n> Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb\n\n",
    "attachments": []
}