Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/RAWBTADCLWRPLXPLKIOGKXJOVNMXD6CO/",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/",
    "message_id": "[email protected]",
    "message_id_hash": "RAWBTADCLWRPLXPLKIOGKXJOVNMXD6CO",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/RAWBTADCLWRPLXPLKIOGKXJOVNMXD6CO/",
    "sender": {
        "address": "aa2tx (a) comcast.net",
        "mailman_id": null,
        "emails": null
    },
    "sender_name": "Anthony Monteiro",
    "subject": "[amsat-bb] Re: ITUNE with Mic-buttons?",
    "date": "2006-10-30T14:08:04Z",
    "parent": null,
    "children": [],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "At 08:40 AM 10/29/2006, SV1BSX wrote:\n\n>Hi folks,\n>\n>  during last couple of days I was looking for setup of  ITUNE (v1.10) with\n>an old\n>RIG by using UP-Down Mic-buttons for Doppler correction.\n>  ...\n>\n>   But,  If I change the command line with \"rx\", in irder to cover the\n>Downlink of\n>FO-29, the ITUNE\n>does not correspond correctly anylonger! (\"itune.cfg\" command is now: rx\n>micbutton 1 435.850 100).\n>The ITUNE seems to accept the command for FO-29 without any obvious problem,\n>but the Doppler correction does not work properly (symptom: always ITUNE\n>trying to correct the frequency, even the Sat is \"out of range\". Always\n>\"Tuning Complete\" LED is OFF !)\n\nHi Mak,\n\nI just tried this and it works perfectly. I think you may be\nconfused because it takes a long time to complete the tuning.\n\nA mic button radio tunes at a maximum rate of 9 clicks per second.\nThis is the fastest rate that you can reliably tune most radios\nwith the mic buttons.\n\nThe beacon of FO-29 is 435.795 MHz. If you use your command line:\n\nrx micbutton 1 435.850 100\n\nthen the radio has to be tuned by 55KHz in 100 Hz clicks which\ntakes more than 1 minute at 900 Hz/Sec.\n\nA better command line would be:\n\nrx micbutton 1 435.795 100\n\nwhich will only take a few seconds to complete tuning.\n\n...\n\n>And once more question: the Doppler correction is it possible for several\n>Satellites without changes in \"itune.cfg\" or just\n>for this one which included in to command-line of  \"itune.cfg\"?\n\nYou can set a different radio config command for each satellite if\nyou want to so you never need to have multiple copies of the itune.cfg\nfile. This is mostly useful for micbutton radios so you can set a\ndifferent start frequency for each satellite. I would suggest starting with\nthe beacon as this will require the least amount of tuning to lock.\n\nTo do this, just put the radio command line after the satellite\ntransponder info. You can also have a default if you like which will\nbe in effect unless you put something different for a particular satellite.\n\nIf you have any more questions, please send me email.\n\n73,\nTony AA2TX\n\n",
    "attachments": []
}