Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/SGBQLOCP54EZHM2ZQT5JDQIUWAI2M6SD/",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/",
    "message_id": "[email protected]",
    "message_id_hash": "SGBQLOCP54EZHM2ZQT5JDQIUWAI2M6SD",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/SGBQLOCP54EZHM2ZQT5JDQIUWAI2M6SD/",
    "sender": {
        "address": "pa3guo (a) upcmail.nl",
        "mailman_id": null,
        "emails": null
    },
    "sender_name": "PA3GUO",
    "subject": "[amsat-bb] Re: station add help",
    "date": "2010-10-31T11:26:31Z",
    "parent": null,
    "children": [
        "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/EDI3GJGYM4NNMVC6NAIX2DEBNR35BNEO/"
    ],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "Hi Jack\n\nI have a Kenwood TS2000, which is very similar to the IC910.\nFor this discussion one important difference, the TS2000 has\na build in TNC, which can be used on either bands & sat mode.\n\nMany years I simply connected that build-in TNC to my PC\nand used Alogger under Windows (via RS232) for packet.\nMostly ISS APRS, but also to command RAFT, ANDE, etc.\n\nTwo years ago I bought a 2nd hand PK96, external TNC,\nwhich I connect to the TS2000 (ACC plug) and PC (RS232).\nWorks fine. It allows me to use the build in TNC on one band\nand the PK96 on the other band. Also, when I use the build-in\nTNC, I cannot use CAT (doppler) access. So to do AND doppler\ncompensation (HRD) AND packet I need the external TNC.\nAlso with the PK96 I use ALogger.\n\nAnother option is to feed the audio to MixW, and create a virtual\nlink in SW: connect MixW to Alogger, then you can set up an APRS \nSatgate without hardware TNC.\n\nhttp://www.youtube.com/watch?v=FSFVTN2KKog shows how\nISS APRS is decoded by MixW.\n\nAudio can directly be decoded by MMSSTV for SSTV (both TX/RX).\nA SW only solution gets you running for SSTV. I did SSTV over HO68\nthis way: http://www.pa3guo.com/ho68_sstv_dec30_007.jpg\n\nOne year ago I added an interface between the radio & PC, to \ndecouple them physically (for 20+ years I was 'unsafe'). For this\nI use a kit from http://www.ezkits.eu/. This is insurance only, it\ndoesn't add anything new.\n\nThen, I use HRD for Doppler control, but it can do much more\nincluding decoding of many digital modes.\n\nWhen you connect the audio of the IC910 to a PC and run MixW\nyou are operational to receive APRS already ! Maybe start there\nand extend then step by step. (oh, you then can also decode\n9k6 from AO51)\n\nSuccess !\nHenk\n--\nHenk, PA3GUO\nhttp://www.pa3guo.com\n\n==============================\nI'm in the process of adding digital mode to my satellite station which \nconsists \nof IC910 radio using SATPC 32 12.8A.  I will be using a Signalink USB & would \nlike to know if this is the way to go.  I will be using it for packet, \ndigipeater, SSTV.etc.  Two programs that I'm looking into using are MIXW & or \nmltimode.  I would appreciate any suggestions or help about moving foreword \nwith \nthis configuration.  \n\n\nThanks for any input. Jack WA1ZDV \n\n",
    "attachments": []
}