Email Detail

HTTP 200 OK
Allow: GET, HEAD, OPTIONS
Content-Type: application/json
Vary: Accept

{
    "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/5T4ZV6XHOAWXJCJVCU7ADYXSS54B6NBJ/",
    "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/",
    "message_id": "CADq4U7LphqSfaNxPJ049UPJGunOSyp=Sg=uMr3XX-E1E7BZ-Rg@mail.gmail.com",
    "message_id_hash": "5T4ZV6XHOAWXJCJVCU7ADYXSS54B6NBJ",
    "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/5T4ZV6XHOAWXJCJVCU7ADYXSS54B6NBJ/",
    "sender": {
        "address": "minyard (a) acm.org",
        "mailman_id": "59a713764a2e4ccabdcfd85f5b213a94",
        "emails": "https://mailman.amsat.org/hyperkitty/api/sender/59a713764a2e4ccabdcfd85f5b213a94/emails/"
    },
    "sender_name": "Corey Minyard",
    "subject": "[pacsat-dev] Re: PACSAT Operating Instructions",
    "date": "2023-05-09T03:51:59Z",
    "parent": null,
    "children": [],
    "votes": {
        "likes": 0,
        "dislikes": 0,
        "status": "neutral"
    },
    "content": "Burns sent me the info on that.  I ran J5 pin 12 to a via on the\nbottom right of U1.  After doing that wiring change, all but one MRAM\nappears to be working.  It looks like R5 got removed somehow, I may\nhave done that removing the wire.  I just installed a bridge there,\nsince it's a zero-ohm resistor, and the mram seems to be working now.\n\nThe temperature sensor on the daughter board seems to be working.\n\nI don't think the 5043's are working.  I'm not getting anything on\ntransmit, and I eventually get:\n\nPacsat>send pb status\n## SELF TEST: pb_test_status\nTX QUEUE FULL: Could not add UI frame to Packet Queue\nPB Empty.\n## PASSED SELF TEST: pb_test_status\n\nafter running that a few times.  At startup, I'm getting:\n\nERROR: In start_rx, axradio_init returned: 5\nERROR: In start_tx, axradio_init_70cm returned: 5Initializing PB Task\nERROR: Failed in init PB Status Timer\n\n-corey\n\nOn Mon, May 8, 2023 at 9:51 PM Jim McCullers via pacsat-dev\n<[email protected]> wrote:\n>\n> Chris,\n>\n> Please take a look at the email I sent out earlier.\n> There is the possibility of a wiring error on the board with my white wire correction.\n>\n> As for the connectors being longer, I never noticed that and these should be the same connectors I sent Burns and Chris.\n> Burns say the MRAM is working after the wiring change and the AX5043s are working for Chris and Burns so not certain there.\n>\n> Attached is the revised schematic.  I'll have the Kicad files on github hopefully tomorrow.  Have a couple of issues to deal with.\n>\n> Jim McCullers\n> WA4CWI\n>\n>\n>\n> I sent this earlier, but just to Chris.\n>\n> I got my board today and soldered on the connectors.  Looking at the board now, I see that the connectors that came with the launchpad are around 1cm longer than the ones Jim supplied.  I can't get the mram or ax5043s to be detected.  I don't think it's making good contact on the connectors, for obvious reasons.  Do I need to trim the old connector, or did I do something wrong?\n>\n> I clipped the pins, and still no help.  The power light by the serial connector works, and the serial port works.  But the mrams and the ax5043's are not there.\n>\n> I can't find the schematics in the git repository.  PacSatDocs, I assume.  I guess I need to start debugging to figure out what is wrong.\n>\n> -corey\n>\n> -----------------------------------------------------------\n>\n> pacsat-dev mailing list -- [email protected]\n> View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected]\n> To unsubscribe send an email to [email protected]\n> Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org\n",
    "attachments": []
}