Email Detail
Show an email
GET /hyperkitty/api/list/[email protected]/email/F4RUWRUIAVD2YE2W7GJWIZMLRTYJK26E/
{ "url": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/email/F4RUWRUIAVD2YE2W7GJWIZMLRTYJK26E/", "mailinglist": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/", "message_id": "[email protected]", "message_id_hash": "F4RUWRUIAVD2YE2W7GJWIZMLRTYJK26E", "thread": "https://mailman.amsat.org/hyperkitty/api/list/[email protected]/thread/F4RUWRUIAVD2YE2W7GJWIZMLRTYJK26E/", "sender": { "address": "wa4cwi (a) bellsouth.net", "mailman_id": "4aa6f1e3f4cd4bf4b1492e47285ca527", "emails": "https://mailman.amsat.org/hyperkitty/api/sender/4aa6f1e3f4cd4bf4b1492e47285ca527/emails/" }, "sender_name": "Jim McCullers", "subject": "[pacsat-dev] Re: PACSAT Operating Instructions", "date": "2023-05-10T19:42:04Z", "parent": null, "children": [], "votes": { "likes": 0, "dislikes": 0, "status": "neutral" }, "content": "Corey,\n\nSorry but list has been offline.\n\nPopulate with 330 ohm or almost anything. Zero may work and that's on my future test list.\nIt's like the zero ohm resistors that we found out were not needed on the MRAMs to as load separation between the chips.\nKicad protested that something had to be there and at that time on the MRAMs we did not know and still do not know on the 5043s.\nNot much literature on putting two on the same SPI bus.\nI ran out of 330s and forgot to populate when the shipment came in.\n\nJim McCullers\nWA4CWI\n\n\n\nIt could be the serial port, that makes some sense, I guess.\n\nI installed a jumper feeding 3.3v on J4 pin 1, and the MRAM still works, but the 5043s still don't.\n\nI think I found it. R10 and R11 are not populated. One of them says\n330 ohms, one says zero. What needs to be put here? I think I have some SM resistors, but probably 0603, and these look smaller.\n\n-corey\n\n> Ok, I got both mails. One thing I notice is that there is some \n> backflow of power from the serial line which lights the LED (dimly) \n> even if the LaunchPad is unpowered. Could that be the reason for the \n> 2.7V? I have those jumpers installed on both halves of the board, but \n> I'm surprised the MRAM works at all if you don't have it installed \n> (maybe that 2.7V is enough---and I don't see how that relates to the 5043).\n\nOn Tue, May 9, 2023 at 9:41 AM Corey Minyard <[email protected]> wrote:\n>\n> I send this from my acm.org account and realised it's not going to get \n> to the pacsat mailing list. So here it is again.\n>\n> On Tue, May 9, 2023 at 9:39 AM Corey Minyard <[email protected]> wrote:\n> >\n> > On Tue, May 09, 2023 at 09:28:06AM -0400, Burns Fisher (AMSAT) wrote:\n> > > Ok, glad the MRAM is working. Any chance that you don't have the \n> > > two jumpers on the LaunchPad required to power the 5043s? These \n> > > would be a pair on the right (components up, USB down, I think) \n> > > just below the bottom set of pins.\n> >\n> > Yes, the two jumpers labeled +5V and +3V3 right by J1 are both installed.\n> > I'm getting 3.3V on J1 pin 1 and 5V on J1 pin 2.\n> >\n> > There are unpopulated jumpers on the LaunchPad by J4 (J6 on the\n> > Laumchpad) that have the same labels. I'm getting 2.7V on J4 pin 1, \n> > which is strange. That's what powers the MRAMs and the temperature \n> > sensor.\n> >\n> > Should I put a jumper on 3V3 by J4? I'm getting 3.3V on the other \n> > side of the jumper. I'm wondering if the power is somehow coming \n> > through the 5043s and getting to the MRAMs, but I don't see how that could happen.\n> >\n> > >\n> > > BTW, I don't even try to push Jim's board all the way on. It is tight as\n> > > it is and I want to be able to get it back off (relatively) easily. But\n> > > regardess, the tops of the pins are all level, even though the \n> > > newly soldered pins have a plastic holder at the bottom and the \n> > > original pins do not.\n> >\n> > Yeah, strange. I didn't notice until I tried to put the board on. \n> > My board now looks terrible, but it seems to be making good contact now.\n> >\n> > I looked at close-up pictures on TI's web site, and the pins I had \n> > look the same as the ones in the picture.\n> >\n> > -corey\n> >\n> > >\n> > > 73,\n> > >\n> > > Burns Fisher, WB1FJ\n> > > *AMSAT(R) Engineering -- Flight Software*\n> > >\n> > >\n> > > On Mon, May 8, 2023 at 11:52 PM Corey Minyard via pacsat-dev < \n> > > [email protected]> wrote:\n> > >\n> > > > Burns sent me the info on that. I ran J5 pin 12 to a via on the \n> > > > bottom right of U1. After doing that wiring change, all but one \n> > > > MRAM appears to be working. It looks like R5 got removed \n> > > > somehow, I may have done that removing the wire. I just \n> > > > installed a bridge there, since it's a zero-ohm resistor, and the mram seems to be working now.\n> > > >\n> > > > The temperature sensor on the daughter board seems to be working.\n> > > >\n> > > > I don't think the 5043's are working. I'm not getting anything \n> > > > on transmit, and I eventually get:\n> > > >\n> > > > Pacsat>send pb status\n> > > > ## SELF TEST: pb_test_status\n> > > > TX QUEUE FULL: Could not add UI frame to Packet Queue PB Empty.\n> > > > ## PASSED SELF TEST: pb_test_status\n> > > >\n> > > > after running that a few times. At startup, I'm getting:\n> > > >\n> > > > ERROR: In start_rx, axradio_init returned: 5\n> > > > ERROR: In start_tx, axradio_init_70cm returned: 5Initializing PB \n> > > > Task\n> > > > ERROR: Failed in init PB Status Timer\n> > > >\n> > > > -corey\n> > > >\n> > > > On Mon, May 8, 2023 at 9:51 PM Jim McCullers via pacsat-dev \n> > > > <[email protected]> wrote:\n> > > > >\n> > > > > Chris,\n> > > > >\n> > > > > Please take a look at the email I sent out earlier.\n> > > > > There is the possibility of a wiring error on the board with \n> > > > > my white\n> > > > wire correction.\n> > > > >\n> > > > > As for the connectors being longer, I never noticed that and \n> > > > > these\n> > > > should be the same connectors I sent Burns and Chris.\n> > > > > Burns say the MRAM is working after the wiring change and the \n> > > > > AX5043s\n> > > > are working for Chris and Burns so not certain there.\n> > > > >\n> > > > > Attached is the revised schematic. I'll have the Kicad files \n> > > > > on github\n> > > > hopefully tomorrow. Have a couple of issues to deal with.\n> > > > >\n> > > > > Jim McCullers\n> > > > > WA4CWI\n> > > > >\n> > > > >\n> > > > >\n> > > > > I sent this earlier, but just to Chris.\n> > > > >\n> > > > > I got my board today and soldered on the connectors. Looking \n> > > > > at the\n> > > > board now, I see that the connectors that came with the \n> > > > launchpad are around 1cm longer than the ones Jim supplied. I \n> > > > can't get the mram or ax5043s to be detected. I don't think \n> > > > it's making good contact on the connectors, for obvious reasons. \n> > > > Do I need to trim the old connector, or did I do something wrong?\n> > > > >\n> > > > > I clipped the pins, and still no help. The power light by the \n> > > > > serial\n> > > > connector works, and the serial port works. But the mrams and \n> > > > the ax5043's are not there.\n> > > > >\n> > > > > I can't find the schematics in the git repository. \n> > > > > PacSatDocs, I\n> > > > assume. I guess I need to start debugging to figure out what is wrong.\n> > > > >\n> > > > > -corey\n> > > > >\n> > > > > -----------------------------------------------------------\n> > > > >\n> > > > > pacsat-dev mailing list -- [email protected] View archives \n> > > > > of this mailing list at\n> > > > https://mailman.amsat.org/hyperkitty/list/[email protected]\n> > > > > To unsubscribe send an email to [email protected] \n> > > > > Manage all of your AMSAT-NA mailing list preferences at\n> > > > https://mailman.amsat.org\n> > > >\n> > > > -----------------------------------------------------------\n> > > >\n> > > > pacsat-dev mailing list -- [email protected] View archives of \n> > > > this mailing list at \n> > > > https://mailman.amsat.org/hyperkitty/list/[email protected]\n> > > > To unsubscribe send an email to [email protected] \n> > > > Manage all of your AMSAT-NA mailing list preferences at \n> > > > https://mailman.amsat.org\n> > > >\n\n-----------------------------------------------------------\n\npacsat-dev mailing list -- [email protected] View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected]\nTo unsubscribe send an email to [email protected] Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org\n\n", "attachments": [] }