Just for future information, I (sort of accidentally) solved my problem! While setting up for field day a couple weeks ago, I checked my antenna (an Alaskan arrow, using only the bottom 2 sections) - and was surprised to notice it was around a 2.2:1 SWR on 435MHz. I thought I remembered it being better than that, but I guess not. I set up the full-length antenna for Field Day, and operated using a borrowed IC-910 (just in case my radio had the problem again.) In the full length configuration, the alaskan arrow is a 1.1:1 match on 435MHz.
A few days after field day while I was putting away my equipment, something dawned on me - I have never had a problem with the 821 while using the antenna in its full length configuration. I don't use it that way very often, primarily for very low (sub 2°) passes of AO-7 and FO-29.
You can probably see where this is going....My theory was that the high(ish) SWR was causing some RFI problems internally in the radio. RF going where it's not supposed to be, on the coax shield etc. I would think that it shouldn't be a problem for the radio to cope with a 2:1 mismatch...but the only way to find out was test the theory.
I put 2 wattmeters inline, one each on the 2m and 70cm feedlines. Transmitting at ~25w on 435mhz, I was seeing around 2.5-3w coming back towards the radio on my 2m feedline. Figuring that probably wasn't a good thing, I borrowed a normal arrow II antenna - checked with the same meter, a 1:1 match on both 435 and 145. Virtually zero reflected power in the same test. I have been using that antenna for two weeks now, and haven't had a single problem with the radio.
So, moral of this story is, check the obvious! Even if you think something is fine, or you think you remember checking it before - make sure. I had literally checked everything else on the radio, except the antenna. And for those of you using the Alaskan arrow, it might be work checking out if it is working as optimally as you think it is. To be honest, I have yet to find a situation where I could make a QSO with the alaskan and not with a regular arrow. I will be keeping the alaskan, probably to use as a base station antenna once I get a mast and rotor put up at my QTH. But from now on, I'll be sticking with the regular arrow for my day-to-day ops.
That's the end of my novel.....just thought this might come in useful for somebody else down the road :-)
73,
- Matthew kk4fem
On Sat, Jun 17, 2017 at 11:59 PM, Nitin Muttin vu3tyg@yahoo.co.in wrote:
Hi Matthew,
I feel this could be related to the "Ribbon Cable contact issue ". There is one ribbon connector behind the S meter which goes to one of the boards. Disconnect the cable by pulling on the connector socket clean the pins on the cable with a rubber eraser (soft) and fix back the connector.
73 Nitin [VU3TYG]
From: Matthew Stevens matthew@mrstevens.net To: Nitin Muttin vu3tyg@yahoo.co.in Cc: "amsat-bb@amsat.org" amsat-bb@amsat.org Sent: Saturday, 17 June 2017 12:18 AM Subject: Re: [amsat-bb] IC-821H problems
Yes, I do. Interestingly, I have not had any problems with FM in either mode J or B. The other day I worked AO-85 successfully, and immediately switched to EO-79, 2m SSB downlink. I heard no telemetry or anything else. Then I pointed the antenna over towards some nearby powerlines, which normally create a lot of annoying static on 2m - nothing heard. I removed the coax from the 2m jack, and observed a drop in the noise level (very slight), reconnected the coax and checked over towards the power lines again, with the same result. I wasn't hearing anything on 2m SSB, after I had, minutes before, had no issues hearing on 2m FM.
I'm glad I have other radios to use in the meantime, while I try to figure this out :-)
73
- Matthew kk4fem
On Sun, Jun 11, 2017 at 2:05 AM, Nitin Muttin vu3tyg@yahoo.co.in wrote:
Hi Matthew,
On 2m when on FM mode do you hear the white noise when you open the squelch.
73 Nitin [VU3TYG]
From: Matthew Stevens matthew@mrstevens.net To: amsat-bb@amsat.org Sent: Saturday, 10 June 2017 7:06 PM Subject: [amsat-bb] IC-821H problems
I'm having a strange issue with my 821. Periodically I lose all sensitivity, which I've particularly noticed on 2m SSB. I can attach and detach an antenna with no change in the noise level, and can't hear anything in the receiver (like the XW-2* beacons, or the AO-73 telemetry). Resetting the radio seems to fix it.
It doesn't appear to be affecting 70cm, although I haven't had much chance to test that (there's not always a mode j sat up at the same time as a mode b one, and when it happens I'm normally just trying to reset the radio as fast as I can do I can operate the pass). Has anyone experienced anything like this before?
73,
- Matthew kk4fem
Sent from my iPhone _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb