thanks very much for trying to help unfortunately it really wasn't what I asked.
hope someone out there might be able to help a newbie out
thanks
N2EHG Myles
On Nov 26, 2011, at 6:49 PM, i6kzr wrote:
Hi Myles, this is what LVB notes teel us about your question:
Calibration from the serial, or virtual serial USB or Ethernet connection
(1)Connect to the unit using a terminal emulator at 9600 bps, 1 stop bit, no parity and no handshake.
(2)Check for communication by typing the ‘C’ key followed by the enter key. Note that there is no echo of your keystrokes. Commands are also not case sensitive. The azimuth should be returned, although it will be the uncalibrated value.
(3)Using either the rotator control box switches or the optional front panel switches, move the rotator to its counter-clockwise end stop (zero degrees), which should be due North or due South depending on your rotator.
(4)Move the elevation to zero degrees.
(5)To set the left-most azimuth, type these four keys in sequence: ‘F’, ‘A’, ‘S’, Enter. You will receive a reponse like: *Az Offset=0099*
(6)To set zero degrees elevation, type the four keys in sequence: ‘F’, ‘E’, ‘S’, Enter. You will receive a response like: *El Offset=0326*
(7)Using either the rotator control box switches or the optional front panel switches, move the rotator clockwise 360 degrees for both (a) 360 degree maximum azimuth rotators and (b) 450 degree South CCW stop rotators. For 450 degree North CCW stop rotators, move the rotator clockwise to 450 degrees.
(8)Move the elevation to either 90 degrees, or 180 degrees, depending on the end stop of your rotator.
(9)To set the right-most azimuth for both (a) 360 degree maximum azimuth rotators and (b) 450 degree South CCW stop rotators, type these four keys in sequence: ‘F’, ‘A’, ‘E’, Enter. For 450 degree North CCW stop rotators, type the four keys in sequence: ‘F’, ‘A’, ‘F’, Enter. In either case, you will receive a reponse like: *Az mul=0.897*
(10)For 90 degree elevation rotators only: to set 90 degrees elevation, type the four keys in sequence: ‘F’, ‘E’, ‘N’, Enter. For 180 degree elevation rotators only: to set 180 degrees elevation, type the four keys in sequence: ‘F’, ‘E’, ‘E’, Enter. In either case, you will receive a response like: *El mul=1.234*
(11)If you have a South CCW stopping rotator, you should key in the three key sequence ‘F’, ‘S’, Enter. For a North CCW stopping rotator (default), key in the three key sequence ‘F’, ‘N’, Enter.
(12)To commit this to EEPROM, type the three keys in sequence: ‘F’, ‘W’, Enter.
(13)When you reset or switch the unit on and off, the calibration parameters should be remembered.
If you wish a front panel buttons calibration, you must use the follow sequence:
Calibration from the front panel buttons
You must have an LCD connected for this to work. To enter calibration mode, hold down one of the four front panel buttons as the unit is switched on. After the welcome screen (and potentially the Bad EEPROM message), you then enter the calibration mode.
The four buttons (from LSB to MSB) are Left, Right, Down, Up. On the LCD, these are referred to as L, R, D, U.
(1)*Set Az=min & press D (U=esc)*Using the L button, move the rotator to its counter-clockwise stop. The R button also operates to move the rotator right, although normally would not be required at this point. Press D to accept, or U to abort the calibration completely.
(2)*Set El=min & press L (R=esc)*Using the D button, move the rotator to the zero elevation stop. The U button also operates to move the rotator up, although normally would not be required at this point. Press L to accept, or R to abort the calibration completely.
(3)*Set Az=max & press D (U=esc)*Using the R button, move the rotator to its clockwise stop. If you are using a 450 degree azimuth rotator with a South CCW stop, you should move the rotator to be at the South position 360 degrees clockwise of the CCW stop. The L button also operates to move the rotator left, although normally would not be required at this point. Press D to accept, or U to abort the calibration completely.
(4)*Set El=max & press L (R=esc)*Using the U button, move the rotator to the maximum elevation stop (90 or 180 degrees). The D button also operates to move the rotator down, although normally would not be required at this point. Press L to accept, or R to abort the calibration completely.
(5)*Az range: 450 U 360 D (R=esc)*For North CCW stop 450 degree rotators, press U. For 360 degree or South CCW stop rotators, press D. Press R to abort the calibration completely.
(6)*El range: 0-90 U 0-180 D (R=esc)*For elevation rotators with a maximum elevation of 90 degrees, press U. For ‘flipping’ elevation rotators, press D. Press R to abort the calibration completely.
(7)*CCW stop North=U South=D (R=esc)*For North CCW stop rotators, press U, for South CCW stop rotators press D. Press R to abort the calibration completely.
(8)*EE Write: U (R=esc)*To commit the settings to EEPROM, press U. Press R to abort the calibration completely.
(9)*EEPROM write OK Push btn to exit*Push any front panel button to return to normal mode.
Have fun, 73
Renzo I6KZRIl 26/11/2011 21.11, myles landstein ha scritto:
Hi
For some reason I couldn't find this online sure I overlooked the obvious....
I have a LVB Tracker with a Yaesu G5500
Wanted to cal the unit and was sure if this was considered
a 360degree max az rotor or 450 South CCW = FEN
or
450North CCW = FEE
also
is this considered
a: If you have a South CCW stopping rotator, you should key in the three key sequence ‘F’, ‘S’, Enter. For a North CCW stopping rotator (default), key in the three key sequence ‘F’, ‘N’, Enter.
thanks
Myles
Sent via AMSAT-BB@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb