I have a IC-9100. In addition to setting the menu item to 9600 baud, the radio has to be in FM digital. To put the IC-9100 into FM digital the FM mode button is de[pressed until the “D” icon shows on the display. This disables the filtering to allow the DUV audio from the satellite to pass onto the sound card. I don’t have an IC-910 so don’t know if this applies to that radio.
I am using the IC-9100 into a computer sound card and Foxtelem and decoding the data and uploading to the server.
Frank K6FW
On Oct 10, 2018, at 7:46 AM, Kevin Zari kk4yel@gmail.com wrote:
Yes, the levels are maxed out. I also hooked up an oscilloscope to verify the signals presence on the line. -Kevin (KK4YEL)
The problem with the world is that the intelligent people are full of doubts, while the stupid ones are full of confidence.
On Oct 10, 2018, at 10:37, Dave Webb KB1PVH kb1pvh@gmail.com wrote:
Kevin,
Have you played with the input levels on the sound card?
Dave-KB1PVH
Sent from my Galaxy S9
On Wed, Oct 10, 2018, 10:17 AM Kevin Zari kk4yel@gmail.com wrote: I’m pulling out what little hair I have left. I have borrowed a friend’s IC-910, and want to feed the output of the radio to both a signalink USB and also to the direct Line-in of the laptop to receive the 9600 bps signal off of the 9600 pin 4 of the Data mini DIN. So here is what I did:
First, I took a cable that was straight through all 6 pins and added a RJ-45 connector on the end, in such a way that pin 1 of the mini DIN was pin 1 of the RJ45 connector, pin 2 was pin 2, ... pin 6 to pin 6, etc...
I created a patch panel with two patches, one that is straight through, and one that crosses pins 4 and 5. More about that in a bit.
The signalink was wired in such a way that it is expecting the input on pin 5, and ground on pin 2. So in this case when I connect up the cable to the signalink with a straight through cat 5e cable, it gets the audio out of the rig at 1200 bps (pin 5).
When I want to use the 9600 bps out, I unplug the cable from the patch panel and connect it up to the other patch, where it takes pin 4 (9600 bps) and throws it on pin 5 of the patch panel output. I then have a cable that takes pin 5 and brings it to the tip of a TS 3.5mm mono cable. Pin 2 (GND) goes to the sleeve. I then plug this into the mic input of an older Apple MacBook Pro.
I remembered to set the IC-910 to 9600 mode. I start FoxTelem and set the input to the Mac’s wired mic input, but I never decode anything.
One thing that is odd to me is that when I toggle the 9600 mode on the IC-910, I do not see / hear a difference. I would imagine it should toggle some signal on and off the pin 4.
Any ideas would be highly appreciated. I have also just tried a simple cable with pin 4 to the tip and pin 2 to the sleeve, and have seen similar results.
I appreciate any ideas, criticism, etc...
-Kevin (KK4YEL)
The problem with the world is that the intelligent people are full of doubts, while the stupid ones are full of confidence. _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb