Paul and all,
I would be curious to hear from anyone currently using verticals with preamps as their primary receive antennas. I have hesitated to respond to your initial post, Paul, because (1) I am very new to the satellites; (2) as a result, my personal experience with antennas involves only the Arrow handheld antenna, the eFactor 0-gain omni antenna, the Elk dual-band log periodic an MFJ mag-mount dual-band vertical for my vehicle, and HT-specific antennas (Pryme AL800, MFJ 1715 and 1717, etc.); and (3) my other knowledge regarding using omni antennas for satellite work is limited to what I have read here and elsewhere on the Internet.
All of that being said, I believe I would opt for something other than a vertical - even with preamps - as my prime base-station antennas for the satellies. I haven't yet built one of the Ramsey preamps, but I intend to as the weather turns cool here in North Georgia and I spend more time inside. I am curious about its ability to improve reception for me with the sFactor, which is an outstanding transmit antenna for reaching the satellites - based on my experiences with it. I also logged more than a dozen contacts involving AO-27, AO-51 and SO-50 using the eFactor with an HT as a handheld antenna. My personal experience suggests that a preamp would help it on the UHF receive side a great deal, although it honestly exceeded my expectations - given the physical size of the UHF part of the antenna.
The N3TL handheld station has worked 46 states, VE1-2-3-4-5-6-8-9, Mexico, Venezuela, Barbados and marimtime mobile stations all on 5 watts' rf out or less. It also has worked 20 states, Ontario, Mexico and Venezuela on .05-watt (50 milliwatts) on the same set of 2 AA Duracell batteries. For the sake of perspective, I made my first-ever satellite contact on June 28th of this year - less than 4 months ago.
From here, output power isn't the issue. I believe your money and time will be best-invested in optimizing the receive side of your satellite station.
Best of luck with it, and 73,
Tim - N3TL AMSAT Member No. 36820 Athens, Ga. - EM84ha -------------- Original message from Edward Cole kl7uw@acsalaska.net: --------------
At 09:30 PM 10/18/2008, 12.01 wrote:
hello,
I have a beginner question. I am in the process of setting up my first satellite station. My initial investment is minimal and I have chosen to start out with a pair of 2m and 70cm omni antennas on the roof. To help out a bit I am also adding a mast mount preamp on each antenna. To protect the preamps they will be switched out of line by a RF sense switch (one for each amp). For reference the two preamps and the pair of RF switches are all made by Ramsey (I know there are better preamps, but not available in my current budget). I am keeping this initial adventure limited to the LEOs (and ISS, etc.).
_The question: _ When I assemble the RF switches I must choose a RF range for the switch to work within. The range is determined by the choice of a specific resistor. The default three ranges suggested are 0-10 watts, 10-30 watts, and 30-100 watts. I would be able to change the range later but it would require removing the unit from the mast.
So... not having any experience (yet),_ what uplink power range is recommend for non-gain antennas?_ Is there one range that should cover the LEOs? If not, how much should I expect the required uplink power needs to vary across various satellites? Is it different for each band? I have read that it is always best to never be louder than the beacon and that's fine. I'm just needing to know where to start off my hardware choices.
Thanks in advance for any help from you folks with the know-how. I look forward to a qso with you.
.paul ac0z _______________________________________________ Sent via AMSAT-BB@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
I'm surprised that you have had only one reply. I am not QRV on the Leos so my advise is not as good as what you might get. My "understanding" is that one can work most of the Leos with power <10w. This is IF the stations on the bird also comply by not using more power than is needed. If a "power war" ensues to try to capture the satellite then running low power may be less effective to "break in".
But seeing that so many folks run HT's that typically are 5w, I think you might chose the lowest range as long as your equipment output matches. You have to consider that you will have no antenna gain using omni-directional antennas so uplink RF power needs are affected, accordingly. NOW if some experienced sat op will add their input on this subject you should have the info you need.
I wonder if the Ramsey preamps allow for "hard" switching. That is by separate control line that the radio PTT controls. Then You have no issue with RF power and would run the units with the RF sense disabled. I should state that "many" (dare I say most) experienced VHFers that run high power (>100w) use hard-wired switching. I know of NO eme stations that use RF sense control lines.
PS: when my standard AO-10/13/40 ground station is re-installed I will have available 5-60w with 16.5 dBc UHF uplink (all-mode).
73, Ed - KL7UW BP40iq, 6m - 3cm 144-EME: FT-847, mgf-1801, 4x-xp20, 185w 1296-EME: DEMI-Xvtr, 0.30 dBNF, 4.9m dish, 60W http://www.kl7uw.com AK VHF-Up Group NA Rep. for DUBUS: dubususa@hotmail.com
Sent via AMSAT-BB@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb