Hi All,
Yes, the 2 lines for SO-50 as below are correct.
SO-50,67.0,$3F,1 SO-50,74.4,$3E,3
As per the SubTone.SQF file:
; SO-50: Before this satellite can be worked it has to be opened by a 74.4 Hertz ; "burst" tone. Therefore the file contains an additional line with data for ; this tone frequency. To set this tone frequency with SatPC32 click the "T" ; control until it shows "T2". Then switch to TX for a few seconds. Click ; the "T" again until it shows "T1". That will set the tone frequency back to ; 67.0 Hertz.
73 Rick VK6XLR
On 1/07/2015 21:04, PY5LF wrote:
Hi friends This set are working nice in my IC9100; SO-50,67.0,$3F,1 SO-50,74.4,$3E,3 I hope it works for you . 73
PY5LF Luciano Fabricio Curitiba-PR-BR GG54jm http://www.qrz.com/db/PY5LF
-----Mensagem original----- De: AMSAT-BB [mailto:amsat-bb-bounces@amsat.org] Em nome de Erich Eichmann Enviada em: quarta-feira, 1 de julho de 2015 09:44 Para: Frank Westphal; AMSAT-BB@amsat.org Assunto: Re: [amsat-bb] IC-9100 SatPC32 Sub Audible Tone for SO-50
Hi Frank, the program should come with the correct data for IC-9100 for the sub tone frequencies for 67.0 and 74.4 Hz. Unfortunately I don't have an IC-9100 (I loaned one from Icom when I added the functions to the program). So, presently I can't test the function myself.
The sub tone frequency must be set on the Sub VFO because it is the TX VFO in Satellite mode. When you check the tone frequency the radio displays the tone frequency of the Main VFO (if I remember correctly). So, did you first swap the VFOs before you checked the tone frequency and whether ist changes to 74.4 with T2?
73s, Erich, DK1TB
Am 01.07.2015 um 07:47 schrieb Frank Westphal:
I have acquired an ICOM IC-9100 and am stumped on how to program SatPC32 to select the correct sub audible tone for SO-50. I have studied the SubToneSQF file and the ICOM manual. When I click on T0 and change it to T1 or T2 in SatPC32 the sub audible tone is turned on in the IC-9100. The tone frequency in the IC-9100 does NOT change to the value in the SubToneSQF file.
Has anyone figured out haw to correctly setup SatPC32 SubToneSQF file to work with the IC-9100? Could you post the correct command line so I could copy it into my file?
Thanks in advance for any guidance.
Frank K6FW
Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb