I continue to be amazed that folks have still not gotten this message:
USE A PREAMP! It is the single most significant item for operating satellites --- succesfully!
Repeat after me: If you cannot hear em - you can not work em! If you cannot hear em - you can not work em! If you cannot hear em - you can not work em! If you cannot hear em - you can not work em! If you cannot hear em - you can not work em!
OK, got it now! You can use a very simple antenna for LEO satellites --- IF YOU USE a PREAMP! For AO-51 mode-U, I have used a 2m whip - 1/4 wavelength (20-inches high) with a 432-MHz preamp. That's it!
You can run a small yagi for your 2m uplink, pointed 20 degrees elevation and either manually rotate it or use a cheap TV rotator. I have used my 3-element Arrow antenna and 5w. Bob Bruninga has explained this a "million" times --- I admire his patience!
So what is the most important part of a satellite station? huh? eh? what?
a preamp
73's Ed - KL7UW
At 12:24 PM 2/22/2007, Amir K9CHP wrote:
I'm working LEO sats with a Kenwood D7AG HT and an Arrow II antenna. I have settled on putting the Arrow on a light tripod in a way that allows me to aim it both in azimuth and elevation and adjust for polarization. In addition, I've added a Hamtronics pre-amp to the 70 cm receiving end of the antenna. It is powered by the smallest 12v SLA battery I could lay my hands on. The amplifier is definitely the best addition to the system. I can now hear satellites at full scale quieting and tune for Doppler by ear and by looking at the scale. Recently, as I'm planning on a trip, I've gone back to work my Pryme AL-800 antenna, just to get more experience with it. Yes, I can work satellites with it and make contacts, but the difference between the Pryme and my regular setup is rather substantial.
So Bruce, I'm definitely with you on pre-amps at the antenna.
73' de Amir K9CHP Member ARRL, AMSAT #36083 Cayuga County Highland SAR www.highlandsar.org 1st Special Response Group www.1srg.org Apprentice Tracker Joel Hardin Professional Tracking Services http://www.jhardin-inc.com
-----Original Message----- From: amsat-bb-bounces@amsat.org [mailto:amsat-bb-bounces@amsat.org] On Behalf Of Bruce Robertson Sent: Thursday, February 22, 2007 12:11 PM To: Gary McKelvie Cc: amsat-bb@amsat.org Subject: [amsat-bb] Re: Advice on antennas for working the LEO's
Quoting Gary McKelvie garym@garym.org.uk:
Several people have suggested using a vertical antenna such as a colinear. I have actually already tried this and the results are very disappointing, which I put down to my location rather than anything else as where I am is not particularly that good certainly form a VHF/UHF point of view.
Gary:
We look forward to working you on this side of the pond. If I remember the details of this thread correctly, one of your design goals for this system is to not require preamps. I would venture to say that most every antenna design or recommendation pertaining to satellite work assumes low-noise preamps as close to the antenna as possible. This might explain the difference between your experience and others' with vertical antennas.
What I love about this aspect of the hobby is the experimentation. Though my antennas are down right now, there have been many silent mid-Atlantic passes of VO-52 where I have amused myself by testing the minimum signal required for reception, used varying antennas, and switched in and out a preamp or two. Just me and an orbiting radio laboratory; thank you, ISRO!
Conducting such experiments with my pair of FT-817s and TS-2000 suggests that a preamp is terribly important, especially for 70cm downlink operation. In fact, my 70cm preamp is an indoor model, and it *still*
makes
a crucial difference. I think this is because the NF of these radios' preamps is just not devised for small-signal work. To put it more
strongly,
I would rather spend an evening doodling around on 70cm with a (indoor) preamp and a coathanger-and-bnc vertical than I would with my 8 element rotating outdoor beam and no preamp!
Your high-gain, narrow bandwidth antennas will make up for this, of
course.
But other beginners might be interested to know that by using preamps and shorter, wider bandwidth antennas it is possible to have exceedingly enjoyable LEO satellite operations with a single, azimuth-only TV-type rotor. The approach offers some advantages: such short antennas are also easier to build from scratch materials, easier to put up on in the air;
and
the wide beamwidth of the antenna makes it possible to manually control
the
rotor without too much fuss. The advantage of your az/el system is that it will be closer to HEO-ready when P3E and SSETI are launched next year. However, I venture to say that you really will need preamps then.
I started out using HRD, but like others, I have found that recent
versions
do not track SSB/CW correctly, and it seems that Simon's focus is now on the latest digital Swiss Army Knife. If you have difficulties of this nature, try the demo of SatPC32 or other dedicated programs.
Again, for others with a different set of resources, there's a great discussion of why a fixed-elevation rotor system works well at: http://web.usna.navy.mil/~bruninga/rotator1.htm I would advise that homebrewers begin avoiding circular polarization and the mechanical challenges that entails. Many of us have had good luck building the so-called 'cheap yagis': http://www.wa5vjb.com/yagi-pdf/cheapyagi.pdf My 70cm one is 8 elements; I found my 4 element 2m to be a bit under-powered for receiving AO-7, but I had fun with it for 2 years!
73, Bruce VE9QRP
Sent via AMSAT-BB@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
Sent via AMSAT-BB@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb