Dear Andrew Glasbrenner and All
We had mail to [email protected] but do not have respond feedback. if you have detail e-mail or contact list of turksat team please advice to me.
Tanan Rangseeprom HS1JAN
----- Original Message ----- From: "Andrew Glasbrenner" [email protected] To: "Tanan Rangseeprom HS1JAN" [email protected] Cc: "PE1RDW" [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected] Sent: Wednesday, July 31, 2013 12:08 AM Subject: Re: [amsat-bb] Re: V/U Linear Transponder
You may want to reach out to the turksat 3U team. Although the satellite has has problems, I believe it has redundant v/u transponders on board.
73, Drew KO4MA
Sent from my iPhone
On Jul 30, 2013, at 12:04 PM, "Tanan Rangseeprom HS1JAN" [email protected] wrote:
Thanks respond for help to me
1.Thailand has regular to forbid for transmitt UHF band but can receive the signal for amateur radio satellites only. we need to used VHF band same like transponder of Japanes (FO-29) , AmSat AO-51 , Saudiarabia SO-50 and other satellites. for interference from China Thailand and other countries on VHF is normal.
2.Ok, I do not have knowledge 100 khz bandwidth is too much for the over power. please advice me for 30 khz uplink 145.90-145.92 MHz VHF / 435.10 - 435.12 MHz UHF of liner transponder.
3.We have to design FM repeater use to modify HX1 / RX2A RADIOMETRIX VHF / UHF transmitter module we have change x-tal to 145.90 MHz / 13.59 MHz and used MC3361 with x-tal 10.245 MHz and CML IC FX465 CTCSS Encode/Decode build test it to be successful.
We and technical team of TAMSAT group would like to help and advice for circuit diagram of V/U transponder same like transponder of Japanes (FO-29) and other satellites. We had mail to Mr.William Leijenaar PE1RAH but do not have respond feedback. Mrs Thida of 100watts ham radio magazine of thailand sugges me to know Mr.William.because she meet him on Tokyo ham fair 2009.
On this time we and technical team of TAMSAT group need help very urgent. we need advice of circuit diagram or datasheet IC for build V/U Liner transponder for payload 1U cubesat of JAISAT satellite project.
Tanan Rangseeprom HS1JAN Project Manager of JAISAT-1 member of RAST email : [email protected]
Thanks for the mail via AMSAT.org
My name is David Bowman G0MRF and I'm a member of the team building FUNcube, due for launch this November.
I can help with transponder design, but there are some points which you need to consider.
- The use of V band for the uplink will be a poor choice for your
location. The interference from China and other countries on 145MHz will mean the transponder will not be usable. Using U band for the uplink is a much better choice.
- The 100kHz bandwidth is too much for the typical power available
from a CubeSat. If you get your RF team to do a link budget analysis, you will see the cubesat power budget will not support 100kHz of bandwidth. Ususally 30kHz is as much as you can do with a 1U cube.
- You may want to consider a FM 'repeater' as there is now only 1 in
orbit, while there are several linear transponder satellites ready to be launched. The FM design will allow you to run a very efficient power amplifier (70%) and power can be saved over oceans and areas of low population by using a 67Hz access tone (CML FX465)
I can assist with design but would need to know if you are planning a 1U 2U or 3U design.
William PE???? is good, but will probably just offer to sell you a transponder.
some old info is available at www.g0mrf.com/transponder.htm
The attached powerpoint has some pictures of the UV transponder and other boards in FUNcube from AMSAT-UK _______________________________________________ Sent via [email protected] Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb