IC-9100 and SATPC tracking help needed
Greetings all.
Trying without success to get my IC-9100 to track with SATPC.
Elmer needed if you've got it going.
Running SatPC32 V.12.8d (2018)
Thank you in advance
Kirk, N0KK
Sent from Outlookhttp://aka.ms/weboutlook
Kirk I use SAT32PC Ver. 12.8c on a laptop running Windows 10 and an IC-9100. I assume your IC-9100 is connected to the PC via a USB cable. Some things I would check: Is the device driver for the IC-9100 Installed? Does the IC-9100 talk to other software such as HRD? In SAT32PC go to Setup>Radio Setup Is the Icom button in the Radio 1 panel checked? Click on Model in the drop-down box. The windows below should say IC-9100 Click on Baudrate in the drop-down box. The windows below should say 9600 Click on Addresses in the drop-down box. The windows below should say $7C $7C. (This are the default addresses in the IC-9100. They can be changed in the IC-9100 but they must match the addresses set in SAT32PC.)
In the Com Port Window my setup shows Com Port 6 but this will vary depending on other USB devices. It can also change when change USB devices. You might try different Com Port numbers. The Cat Delay box should show 70.
The Satellite Mode box should be checked. The RTS, DTR and KCT boxes should be unchecked.
At the bottom right corner of the SAT32PC main window does it show Doppl. Corr: Up/Dwn ?
Then of course the in the upper left of the SAT32PC window there should be C+ showing when you click on it. If there is some other setting that you would like to compare e-mail me directly.
Hope this helps. 73 Al - AF5VH
-----Original Message----- From: AMSAT-BB amsat-bb-bounces@amsat.org On Behalf Of Kirk P Sent: Friday, June 8, 2018 5:22 PM To: amsat-bb@amsat.org Subject: [amsat-bb] IC-9100 and SATPC tracking help needed
Greetings all.
Trying without success to get my IC-9100 to track with SATPC.
Elmer needed if you've got it going.
Running SatPC32 V.12.8d (2018)
Thank you in advance
Kirk, N0KK
Sent from Outlookhttp://aka.ms/weboutlook _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Alfred and others.
TU!
It appears to now be tracking along.
Im not sure why, but it does seem to loose connections at times.
Im using the MicroHam MK2R+ as my interface as I do with all my software. For some reason this was hard to get communicating. The issue was in the HEX address.
For my VHF contesting this weekend I was using Writelog and it does not have IC-9100 as option of all things. So I had to emulate another ICOM for it to talk. While running SATPC on another screen It was looking for the 9100 address but not getting it. Once I was told how to do the drop down and set address in SATPC it made sense...simple but overlooked..as it usually is.
Will be good to get back on the birds after about 5 years. New KNWD HT and ELK and soon Ill have larger ants ready for home qth on az/el rotor now that EME sation is down for summer.
Again, thanks to all.
Kirk, N0KK EN35
Sent from Outlookhttp://aka.ms/weboutlook
________________________________ From: Alfred Watts awatts44@comcast.net Sent: Saturday, June 9, 2018 1:32 PM To: 'Kirk P'; amsat-bb@amsat.org Subject: RE: [amsat-bb] IC-9100 and SATPC tracking help needed
Kirk I use SAT32PC Ver. 12.8c on a laptop running Windows 10 and an IC-9100. I assume your IC-9100 is connected to the PC via a USB cable. Some things I would check: Is the device driver for the IC-9100 Installed? Does the IC-9100 talk to other software such as HRD? In SAT32PC go to Setup>Radio Setup Is the Icom button in the Radio 1 panel checked? Click on Model in the drop-down box. The windows below should say IC-9100 Click on Baudrate in the drop-down box. The windows below should say 9600 Click on Addresses in the drop-down box. The windows below should say $7C $7C. (This are the default addresses in the IC-9100. They can be changed in the IC-9100 but they must match the addresses set in SAT32PC.)
In the Com Port Window my setup shows Com Port 6 but this will vary depending on other USB devices. It can also change when change USB devices. You might try different Com Port numbers.
The Cat Delay box should show 70.
The Satellite Mode box should be checked. The RTS, DTR and KCT boxes should be unchecked.
At the bottom right corner of the SAT32PC main window does it show Doppl. Corr: Up/Dwn ?
Then of course the in the upper left of the SAT32PC window there should be C+ showing when you click on it. If there is some other setting that you would like to compare e-mail me directly.
Hope this helps. 73 Al - AF5VH
-----Original Message----- From: AMSAT-BB amsat-bb-bounces@amsat.org On Behalf Of Kirk P Sent: Friday, June 8, 2018 5:22 PM To: amsat-bb@amsat.org Subject: [amsat-bb] IC-9100 and SATPC tracking help needed
Greetings all.
Trying without success to get my IC-9100 to track with SATPC.
Elmer needed if you've got it going.
Running SatPC32 V.12.8d (2018)
Thank you in advance
Kirk, N0KK
Sent from Outlookhttp://aka.ms/weboutlook _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
participants (2)
-
Alfred Watts -
Kirk P