IC-9700 & foxtelem 1.08p
Hi All, Any IC-9700 users out there that have switched to foxtelem 1.08p using USB and IQ mode? I see a good eye but get zero decodes, dropping back to 1.07y and it all starts working again.
73 Kevin WA7FWF
I you are using the Raised Cosine decoder, try the Windows Sinc instead.
73,
Alan WA4SCA
From: Kevin via AMSAT-BB Sent: Wednesday, October 30, 2019 12:21 AM To: [email protected] Subject: [amsat-bb] IC-9700 & foxtelem 1.08p
Hi All, Any IC-9700 users out there that have switched to foxtelem 1.08p using USB and IQ mode? I see a good eye but get zero decodes, dropping back to 1.07y and it all starts working again.
73 Kevin WA7FWF _______________________________________________ Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
Hi Kevin. I'm having the same problem with my 9700 in IQ mode, and ver 1.08p. I already contacted Chris about the problem.
73 Jeff kb2m
-----Original Message----- From: AMSAT-BB [mailto:[email protected]] On Behalf Of Kevin via AMSAT-BB Sent: Wednesday, October 30, 2019 1:20 AM To: [email protected] Subject: [amsat-bb] IC-9700 & foxtelem 1.08p
Hi All, Any IC-9700 users out there that have switched to foxtelem 1.08p using USB and IQ mode? I see a good eye but get zero decodes, dropping back to 1.07y and it all starts working again.
73 Kevin WA7FWF
I tried that yesterday and it didn't work....
73 Jeff kb2m
-----Original Message----- From: AMSAT-BB [mailto:[email protected]] On Behalf Of Alan via AMSAT-BB Sent: Wednesday, October 30, 2019 2:21 AM To: Kevin; [email protected] Subject: Re: [amsat-bb] IC-9700 & foxtelem 1.08p
I you are using the Raised Cosine decoder, try the Windows Sinc instead.
73,
Alan WA4SCA
From: Kevin via AMSAT-BB Sent: Wednesday, October 30, 2019 12:21 AM To: [email protected] Subject: [amsat-bb] IC-9700 & foxtelem 1.08p
Hi All, Any IC-9700 users out there that have switched to foxtelem 1.08p using USB and IQ mode? I see a good eye but get zero decodes, dropping back to 1.07y and it all starts working again.
73 Kevin WA7FWF
Hi Alan and everyone else that replied,
Windows Sinc also has zero decodes, tried all decoder modes.
for now 1.07y FTW
Thanks Kevin
On 10/29/2019 23:20, Alan wrote:
I you are using the Raised Cosine decoder, try the Windows Sinc instead.
73,
Alan
WA4SCA
*From: *Kevin via AMSAT-BB mailto:[email protected] *Sent: *Wednesday, October 30, 2019 12:21 AM *To: *[email protected] mailto:[email protected] *Subject: *[amsat-bb] IC-9700 & foxtelem 1.08p
Hi All,
Any IC-9700 users out there that have switched to foxtelem 1.08p
using USB and IQ mode? I see a good eye but get zero decodes, dropping
back to 1.07y and it all starts working again.
73
Kevin WA7FWF
Sent via [email protected]. AMSAT-NA makes this open forum available
to all interested persons worldwide without requiring membership. Opinions expressed
are solely those of the author, and do not reflect the official views of AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite program!
Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
I'm going to wait for the fix for the 9700. In the meantime I'm now collecting telemetry with my FIAB with a eggbeater antenna setup that I'm going to leave up here for the winter. I'm seeing a much better decode rate with 1.08p over 1.07y, about 2 to 1. So I'm seeing 1.08 is clearly better then 1.07. Thanks Chris!
73 Jeff kb2m
-----Original Message----- From: AMSAT-BB [mailto:[email protected]] On Behalf Of Kevin via AMSAT-BB Sent: Wednesday, October 30, 2019 12:54 PM To: [email protected] Subject: Re: [amsat-bb] IC-9700 & foxtelem 1.08p
Hi Alan and everyone else that replied,
Windows Sinc also has zero decodes, tried all decoder modes.
for now 1.07y FTW
Thanks Kevin
On 10/29/2019 23:20, Alan wrote:
I you are using the Raised Cosine decoder, try the Windows Sinc instead.
73,
Alan
WA4SCA
*From: *Kevin via AMSAT-BB mailto:[email protected] *Sent: *Wednesday, October 30, 2019 12:21 AM *To: *[email protected] mailto:[email protected] *Subject: *[amsat-bb] IC-9700 & foxtelem 1.08p
Hi All,
Any IC-9700 users out there that have switched to foxtelem 1.08p
using USB and IQ mode? I see a good eye but get zero decodes, dropping
back to 1.07y and it all starts working again.
73
Kevin WA7FWF
Sent via [email protected]. AMSAT-NA makes this open forum available
to all interested persons worldwide without requiring membership. Opinions expressed
are solely those of the author, and do not reflect the official views of AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite program!
Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
I have tried to reproduce this, but I do not have a 9700 so it is hard. So far I can not work out what is wrong.
Can someone describe the setup with the 9700? How is the audio read into the computer and sent to FoxTelem? Is FoxTelem reading it from a sound card? Or what looks like a sound card?
Can someone use Audacity and record some audio for me to test with? Try to record it at the sample rate you use in FoxTelem. e.g. if you set FoxTelem to IQ and 48000 samples per second, then set Audacity to 48000 too.
thanks Chris
On Wed, Oct 30, 2019 at 1:23 PM jeff griffin via AMSAT-BB < [email protected]> wrote:
I'm going to wait for the fix for the 9700. In the meantime I'm now collecting telemetry with my FIAB with a eggbeater antenna setup that I'm going to leave up here for the winter. I'm seeing a much better decode rate with 1.08p over 1.07y, about 2 to 1. So I'm seeing 1.08 is clearly better then 1.07. Thanks Chris!
73 Jeff kb2m
-----Original Message----- From: AMSAT-BB [mailto:[email protected]] On Behalf Of Kevin via AMSAT-BB Sent: Wednesday, October 30, 2019 12:54 PM To: [email protected] Subject: Re: [amsat-bb] IC-9700 & foxtelem 1.08p
Hi Alan and everyone else that replied,
Windows Sinc also has zero decodes, tried all decoder modes.
for now 1.07y FTW
Thanks Kevin
On 10/29/2019 23:20, Alan wrote:
I you are using the Raised Cosine decoder, try the Windows Sinc instead.
73,
Alan
WA4SCA
*From: *Kevin via AMSAT-BB mailto:[email protected] *Sent: *Wednesday, October 30, 2019 12:21 AM *To: *[email protected] mailto:[email protected] *Subject: *[amsat-bb] IC-9700 & foxtelem 1.08p
Hi All,
Any IC-9700 users out there that have switched to foxtelem 1.08p
using USB and IQ mode? I see a good eye but get zero decodes, dropping
back to 1.07y and it all starts working again.
73
Kevin WA7FWF
Sent via [email protected]. AMSAT-NA makes this open forum available
to all interested persons worldwide without requiring membership. Opinions expressed
are solely those of the author, and do not reflect the official views of AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
Chris, The 9700 outputs a 12khz IF signal that is passed to the internal codec and then out the USB port and windows treats it as a soundcard. I used audacity to create about a 2min file and then read it in on 1.07y to verify it is good. I uploaded it to dropbox and the link is https://www.dropbox.com/s/eh5bya72y8gfskt/fox1.wav?dl=0
it was recorded at 48000 and has been saved as a wav
Thanks Kevin wa7fwf
On 10/30/2019 13:59, Chris Thompson via AMSAT-BB wrote:
I have tried to reproduce this, but I do not have a 9700 so it is hard. So far I can not work out what is wrong.
Can someone describe the setup with the 9700? How is the audio read into the computer and sent to FoxTelem? Is FoxTelem reading it from a sound card? Or what looks like a sound card?
Can someone use Audacity and record some audio for me to test with? Try to record it at the sample rate you use in FoxTelem. e.g. if you set FoxTelem to IQ and 48000 samples per second, then set Audacity to 48000 too.
thanks Chris
On Wed, Oct 30, 2019 at 1:23 PM jeff griffin via AMSAT-BB < [email protected]> wrote:
I'm going to wait for the fix for the 9700. In the meantime I'm now collecting telemetry with my FIAB with a eggbeater antenna setup that I'm going to leave up here for the winter. I'm seeing a much better decode rate with 1.08p over 1.07y, about 2 to 1. So I'm seeing 1.08 is clearly better then 1.07. Thanks Chris!
73 Jeff kb2m
-----Original Message----- From: AMSAT-BB [mailto:[email protected]] On Behalf Of Kevin via AMSAT-BB Sent: Wednesday, October 30, 2019 12:54 PM To: [email protected] Subject: Re: [amsat-bb] IC-9700 & foxtelem 1.08p
Hi Alan and everyone else that replied,
Windows Sinc also has zero decodes, tried all decoder modes.for now 1.07y FTW
Thanks Kevin
On 10/29/2019 23:20, Alan wrote:
I you are using the Raised Cosine decoder, try the Windows Sinc instead.
73,
Alan
WA4SCA
*From: *Kevin via AMSAT-BB mailto:[email protected] *Sent: *Wednesday, October 30, 2019 12:21 AM *To: *[email protected] mailto:[email protected] *Subject: *[amsat-bb] IC-9700 & foxtelem 1.08p
Hi All,
Any IC-9700 users out there that have switched to foxtelem 1.08p
using USB and IQ mode? I see a good eye but get zero decodes, dropping
back to 1.07y and it all starts working again.
73
Kevin WA7FWF
Sent via [email protected]. AMSAT-NA makes this open forum available
to all interested persons worldwide without requiring membership. Opinions expressed
are solely those of the author, and do not reflect the official views of AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
participants (4)
-
Alan -
Chris Thompson -
jeff griffin -
Kevin