SatPC32: How to change a K3 to DATA mode for PSAT-1 ?
I have been trying to lash-up everything for ops on 28.120 (USB) PSK31 Uplink and 435.350 (FM) Downlink for PSAT-1 .
Well, in order for my K# to be keyed by the soundcard SIGNALINK-USB, the K3 must be in DATA mode ("MD6;" is the K3's command I believe).
I have moderate success telling SatPC32 that the 2nd radio is a Kenwood, other .
So when SatPC32 reads the Doppler.sqf file, it will change my K3 to CW or to FM or USB. None of which, if used, will allow MixW or DopplerPSK to do anything more than "switch" on the SignaLink and also cause the K3 so "switch" to the xmit (red lite on) position. Yet there is, as expected, no RF output that way, in USB.
So using two different SignaLink's I have the IC910H going to the 435 rx freq and listening. I have the K3 on another SignaLink, going to 28.120 and switching to xmit when asked.
Just that I need to K3 to automatically go into DATA mode when being used for PSAT-1, or any other PSK type bird.
When I manually switch the K3, then either MixW or DopplerPSK do, in fact, switch the K3 to xmit as-well-as output RF .
This is not a very good solution as sometimes SatPC32 re-reads Doppler.sqf and thus puts K3 back to USB.
Anyone have a solution?
tnx !
There is no need for doppler rig control for PSK31 on PSAT. In fact, it wont work because doppler correction has to be phase coherent and you cannot do that by rig control.
Better to just run constant frequency around 28.121 MHz.
But the best way is to run Andy's uplink-only program written for PSAT so that it pre-compensates for doppler at the audio level and also lets you run full duplex from your regular PSK31 program.
Bob
On Sat, Nov 7, 2015 at 7:37 AM, Bob KD7YZ kd7yz@denstarfarm.us wrote:
I have been trying to lash-up everything for ops on 28.120 (USB) PSK31 Uplink and 435.350 (FM) Downlink for PSAT-1 .
Well, in order for my K# to be keyed by the soundcard SIGNALINK-USB, the K3 must be in DATA mode ("MD6;" is the K3's command I believe).
I have moderate success telling SatPC32 that the 2nd radio is a Kenwood, other .
So when SatPC32 reads the Doppler.sqf file, it will change my K3 to CW or to FM or USB. None of which, if used, will allow MixW or DopplerPSK to do anything more than "switch" on the SignaLink and also cause the K3 so "switch" to the xmit (red lite on) position. Yet there is, as expected, no RF output that way, in USB.
So using two different SignaLink's I have the IC910H going to the 435 rx freq and listening. I have the K3 on another SignaLink, going to 28.120 and switching to xmit when asked.
Just that I need to K3 to automatically go into DATA mode when being used for PSAT-1, or any other PSK type bird.
When I manually switch the K3, then either MixW or DopplerPSK do, in fact, switch the K3 to xmit as-well-as output RF .
This is not a very good solution as sometimes SatPC32 re-reads Doppler.sqf and thus puts K3 back to USB.
Anyone have a solution?
tnx !
-- 73, Bob KD7YZ www.qrz.com/db/kd7yz AmSat LM#901 _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
On 07-Nov-15 1001, Robert Bruninga wrote:
There is no need for doppler rig control for PSK31 on PSAT.
I need the K3 to automatically switch to, and stay in, DATA mode so I can xmit the PSK31.
USB mode, at least on my K3, will key down but provide no audio output from the SignaLink.
All my WSJT work always goes thru DATA mode.
Satpc32 is moving the antennas for me. When I make a change to another Satellite, SatPC32 changes both the IC910 and if needed the K3.
SatPC32 doesn't program but three rigs. K3 isn't one of them yet. But there is a little inter-connectivity by using selection of Kenwood.
participants (2)
-
Bob KD7YZ -
Robert Bruninga