Hi All, I was wondering if anyone has had any problem with SatPC32c and CAT control. I have been running SatPC32b with the 910H and everything worked perfectly. I upgraded to version "C" and the LVB rotor control works fine but I cannot get the CAT working. I made sure everything worked Ok with Ham Radio Deluxe, and it worked flawlessly changed frequencies and mode with no problems using the same com port. If anyone can point me in the right direction to correct this, it would be greatly appreciated.
Thanks,73 Carm,WO3T
Hi Carmen,
I'm having trouble with my TS-2000 as well, but I have not used it for a while (and have not really tried to debug it very much). However, check the release notes on SatPC32c. When I was scanning around, I found that it said to change a couple check boxes for some radios. It did not solve my TS-2000 problem, but I don't remember if the 910H was also one that required a change.
73,
Burns W2BFJ
On Wed, Dec 16, 2015 at 12:44 PM, Carmen Peca [email protected] wrote:
Hi All, I was wondering if anyone has had any problem with SatPC32c and CAT control. I have been running SatPC32b with the 910H and everything worked perfectly. I upgraded to version "C" and the LVB rotor control works fine but I cannot get the CAT working. I made sure everything worked Ok with Ham Radio Deluxe, and it worked flawlessly changed frequencies and mode with no problems using the same com port. If anyone can point me in the right direction to correct this, it would be greatly appreciated.
Thanks,73 Carm,WO3T
Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Also, you cannot run HRD at the same time you run SatPC32 and have cat control (pretty sure on this)
73, Ted K7TRK
-----Original Message----- From: AMSAT-BB [mailto:[email protected]] On Behalf Of Burns Fisher Sent: Wednesday, December 16, 2015 10:01 AM To: Carmen Peca Cc: AMSAT BB Subject: Re: [amsat-bb] SatPC32c Problem..........
Hi Carmen,
I'm having trouble with my TS-2000 as well, but I have not used it for a while (and have not really tried to debug it very much). However, check the release notes on SatPC32c. When I was scanning around, I found that it said to change a couple check boxes for some radios. It did not solve my TS-2000 problem, but I don't remember if the 910H was also one that required a change.
73,
Burns W2BFJ
On Wed, Dec 16, 2015 at 12:44 PM, Carmen Peca [email protected] wrote:
Hi All, I was wondering if anyone has had any problem with SatPC32c and CAT control. I have been running SatPC32b with the 910H and everything worked perfectly. I upgraded to version "C" and the LVB rotor control works fine but I cannot get the CAT working. I made sure everything worked Ok with Ham Radio Deluxe, and it worked flawlessly changed frequencies and mode with no problems using the same com port. If anyone can point me in the right direction to correct this, it would be
greatly appreciated.
Thanks,73 Carm,WO3T
Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
As someone mentioned earlier. Make sure you are not running HRD or any other application at the same time on that port. Be sure that SatPC is still set up to the correct port.
I am running 64-bit, Windows 10, with Prolific USB-to-serial converters under SatPC 12.8c with no problems on my IC-910.
Reid, W4UPD
On 12/16/2015 12:44 PM, Carmen Peca wrote:
Hi All, I was wondering if anyone has had any problem with SatPC32c and CAT control. I have been running SatPC32b with the 910H and everything worked perfectly. I upgraded to version "C" and the LVB rotor control works fine but I cannot get the CAT working. I made sure everything worked Ok with Ham Radio Deluxe, and it worked flawlessly changed frequencies and mode with no problems using the same com port. If anyone can point me in the right direction to correct this, it would be greatly appreciated.
Thanks,73 Carm,WO3T
Sent via [email protected]. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
participants (4)
-
Burns Fisher -
Carmen Peca -
Ted -
w4upd