I've been decoding and uploading AO-73 data with the Funcube-1 Dashboard.
I just downloaded and installed JY1-Sat Dashboard.
IAre the Site ID (my call) and the Auth code the same for both upload sites?
I should have a pass of EO-88 in about 30 minutes. Is there any indication from the software that my data is being accepted at the site, based on the same ID and Auth as for AO-73 ?
TIA, 73, N0AN Hasan
Hi Hasan,
Yes you site id authentication can be the same for all dashboards, currently FC1 and Nayif. You can also use the same id for the new ESEO and JY1SAT dashboard from next week (hopefully).
If you are running the FC1 dashboard and it receives and decodes data from Nayif- it will send these to the Data Warehouse automatically. You will see the bottom RH count going up beyond the LH number. Youcan, usually run both dashbaords at the saem time if you wish to display everything!
73
Graham
On 16/11/2018 16:07, Hasan al-Basri wrote:
I've been decoding and uploading AO-73 data with the Funcube-1 Dashboard.
I just downloaded and installed JY1-Sat Dashboard.
IAre the Site ID (my call) and the Auth code the same for both upload sites?
I should have a pass of EO-88 in about 30 minutes. Is there any indication from the software that my data is being accepted at the site, based on the same ID and Auth as for AO-73 ?
TIA, 73, N0AN Hasan _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Graham, I can't thank you enough. I now have 3 dashboards installed, FC-1, Nayaf-1 and JY1-Sat. I can run all at the same time, and I can also run 3 receivers at a time, all feeding their audio streams to the software (SDRs are soooo nice)
Awaiting my 1st nayaf-1 tlme pass (3 min AOS). Signals were quite strong earlier, but I didn't have the right decoder software up yet.
Thanks again. 73, N0AN Hasan
On Fri, Nov 16, 2018 at 10:27 AM Graham Shirville graham@shirville.com wrote:
Hi Hasan,
Yes you site id authentication can be the same for all dashboards, currently FC1 and Nayif. You can also use the same id for the new ESEO and JY1SAT dashboard from next week (hopefully).
If you are running the FC1 dashboard and it receives and decodes data from Nayif- it will send these to the Data Warehouse automatically. You will see the bottom RH count going up beyond the LH number. Youcan, usually run both dashbaords at the saem time if you wish to display everything!
73
Graham
On 16/11/2018 16:07, Hasan al-Basri wrote:
I've been decoding and uploading AO-73 data with the Funcube-1 Dashboard.
I just downloaded and installed JY1-Sat Dashboard.
IAre the Site ID (my call) and the Auth code the same for both upload
sites?
I should have a pass of EO-88 in about 30 minutes. Is there any
indication
from the software that my data is being accepted at the site, based on
the
same ID and Auth as for AO-73 ?
TIA, 73, N0AN Hasan _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership.
Opinions expressed
are solely those of the author, and do not reflect the official views of
AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Ok, just so that I am clear - I can run one dashboard (i.e funcube dashboard) and it will decode FunCube, NAYIF-1 and JY1SAT telemetry correctly identifying the source satellite and send that data to the warehouse and the correct telemetry for the correct satellite get put in the right place?
I have just started playing around with decoding FunCube and NAYIF telemtry, and lookin forward to JY1SAT and have been trying to devise a plan on how to do all three at the same time.
I was going to run one instance of each of the dashboards and schedule a receiver to change frequencies for a specific satellite when in view but it sounds like I can just one dashboard and feed it with my one receiver with it's scheduled frequency changes.
Is that correct?
cheers, Graham ve3gtc FN25 near Ottawa Canada
On 11/16/2018, "Hasan al-Basri" hbasri.schiers6@gmail.com wrote:
Graham, I can't thank you enough. I now have 3 dashboards installed, FC-1, Nayaf-1 and JY1-Sat. I can run all at the same time, and I can also run 3 receivers at a time, all feeding their audio streams to the software (SDRs are soooo nice)
Awaiting my 1st nayaf-1 tlme pass (3 min AOS). Signals were quite strong earlier, but I didn't have the right decoder software up yet.
Thanks again. 73, N0AN Hasan
On Fri, Nov 16, 2018 at 10:27 AM Graham Shirville graham@shirville.com wrote:
Hi Hasan,
Yes you site id authentication can be the same for all dashboards, currently FC1 and Nayif. You can also use the same id for the new ESEO and JY1SAT dashboard from next week (hopefully).
If you are running the FC1 dashboard and it receives and decodes data from Nayif- it will send these to the Data Warehouse automatically. You will see the bottom RH count going up beyond the LH number. Youcan, usually run both dashbaords at the saem time if you wish to display everything!
73
Graham
On 16/11/2018 16:07, Hasan al-Basri wrote:
I've been decoding and uploading AO-73 data with the Funcube-1 Dashboard.
I just downloaded and installed JY1-Sat Dashboard.
IAre the Site ID (my call) and the Auth code the same for both upload
sites?
I should have a pass of EO-88 in about 30 minutes. Is there any
indication
from the software that my data is being accepted at the site, based on
the
same ID and Auth as for AO-73 ?
TIA, 73, N0AN Hasan _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership.
Opinions expressed
are solely those of the author, and do not reflect the official views of
AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Just rushing for plane but yes either way will work ok but iif you want to display the tlm from each then you need to run the three dashboards..
thanks
Graham
On 16/11/2018 17:17, planophore@aei.ca wrote:
Ok, just so that I am clear - I can run one dashboard (i.e funcube dashboard) and it will decode FunCube, NAYIF-1 and JY1SAT telemetry correctly identifying the source satellite and send that data to the warehouse and the correct telemetry for the correct satellite get put in the right place?
I have just started playing around with decoding FunCube and NAYIF telemtry, and lookin forward to JY1SAT and have been trying to devise a plan on how to do all three at the same time.
I was going to run one instance of each of the dashboards and schedule a receiver to change frequencies for a specific satellite when in view but it sounds like I can just one dashboard and feed it with my one receiver with it's scheduled frequency changes.
Is that correct?
cheers, Graham ve3gtc FN25 near Ottawa Canada
On 11/16/2018, "Hasan al-Basri" hbasri.schiers6@gmail.com wrote:
Graham, I can't thank you enough. I now have 3 dashboards installed, FC-1, Nayaf-1 and JY1-Sat. I can run all at the same time, and I can also run 3 receivers at a time, all feeding their audio streams to the software (SDRs are soooo nice)
Awaiting my 1st nayaf-1 tlme pass (3 min AOS). Signals were quite strong earlier, but I didn't have the right decoder software up yet.
Thanks again. 73, N0AN Hasan
On Fri, Nov 16, 2018 at 10:27 AM Graham Shirville graham@shirville.com wrote:
Hi Hasan,
Yes you site id authentication can be the same for all dashboards, currently FC1 and Nayif. You can also use the same id for the new ESEO and JY1SAT dashboard from next week (hopefully).
If you are running the FC1 dashboard and it receives and decodes data from Nayif- it will send these to the Data Warehouse automatically. You will see the bottom RH count going up beyond the LH number. Youcan, usually run both dashbaords at the saem time if you wish to display everything!
73
Graham
On 16/11/2018 16:07, Hasan al-Basri wrote:
I've been decoding and uploading AO-73 data with the Funcube-1 Dashboard.
I just downloaded and installed JY1-Sat Dashboard.
IAre the Site ID (my call) and the Auth code the same for both upload
sites?
I should have a pass of EO-88 in about 30 minutes. Is there any
indication
from the software that my data is being accepted at the site, based on
the
same ID and Auth as for AO-73 ?
TIA, 73, N0AN Hasan _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership.
Opinions expressed
are solely those of the author, and do not reflect the official views of
AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Got it. Hasan
On Fri, Nov 16, 2018 at 11:46 AM Graham Shirville graham@shirville.com wrote:
Just rushing for plane but yes either way will work ok but iif you want to display the tlm from each then you need to run the three dashboards..
thanks
Graham
On 16/11/2018 17:17, planophore@aei.ca wrote:
Ok, just so that I am clear - I can run one dashboard (i.e funcube dashboard) and it will decode FunCube, NAYIF-1 and JY1SAT telemetry correctly identifying the source satellite and send that data to the warehouse and the correct telemetry for the correct satellite get put in the right place?
I have just started playing around with decoding FunCube and NAYIF telemtry, and lookin forward to JY1SAT and have been trying to devise a plan on how to do all three at the same time.
I was going to run one instance of each of the dashboards and schedule a receiver to change frequencies for a specific satellite when in view but it sounds like I can just one dashboard and feed it with my one receiver with it's scheduled frequency changes.
Is that correct?
cheers, Graham ve3gtc FN25 near Ottawa Canada
On 11/16/2018, "Hasan al-Basri" hbasri.schiers6@gmail.com wrote:
Graham, I can't thank you enough. I now have 3 dashboards installed, FC-1,
Nayaf-1
and JY1-Sat. I can run all at the same time, and I can also run 3
receivers
at a time, all feeding their audio streams to the software (SDRs are
soooo
nice)
Awaiting my 1st nayaf-1 tlme pass (3 min AOS). Signals were quite strong earlier, but I didn't have the right decoder software up yet.
Thanks again. 73, N0AN Hasan
On Fri, Nov 16, 2018 at 10:27 AM Graham Shirville <graham@shirville.com
wrote:
Hi Hasan,
Yes you site id authentication can be the same for all dashboards, currently FC1 and Nayif. You can also use the same id for the new ESEO and JY1SAT dashboard from next week (hopefully).
If you are running the FC1 dashboard and it receives and decodes data from Nayif- it will send these to the Data Warehouse automatically. You will see the bottom RH count going up beyond the LH number. Youcan, usually run both dashbaords at the saem time if you wish to display everything!
73
Graham
On 16/11/2018 16:07, Hasan al-Basri wrote:
I've been decoding and uploading AO-73 data with the Funcube-1
Dashboard.
I just downloaded and installed JY1-Sat Dashboard.
IAre the Site ID (my call) and the Auth code the same for both upload
sites?
I should have a pass of EO-88 in about 30 minutes. Is there any
indication
from the software that my data is being accepted at the site, based on
the
same ID and Auth as for AO-73 ?
TIA, 73, N0AN Hasan _______________________________________________ Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership.
Opinions expressed
are solely those of the author, and do not reflect the official views
of
AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership.
Opinions expressed
are solely those of the author, and do not reflect the official views
of AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
participants (3)
-
Graham Shirville -
Hasan al-Basri -
planophore＠aei.ca