Does anyone have pinouts for the Icom IC-910H's C-IV port? I'm hoping to fashion a USB-to-serial adaptor for it, rather than buying Icom's expensive little box. I'm concerned, though, because it looks like it uses a mono plug, so I don't know exactly how it communicates.
TIA, Rick
It's a mono bus - just data and ground.
If you have a couple of transistors and diodes sitting around you can build at least a one way interface, I put one on a bit of PC board and it works great for both programming my 208h* and for controlling my 475.
*208h programming port is the right side of the audio output jack, rather than the center pin as in C-IV jacks
Rick Mann wrote:
Does anyone have pinouts for the Icom IC-910H's C-IV port? I'm hoping to fashion a USB-to-serial adaptor for it, rather than buying Icom's expensive little box. I'm concerned, though, because it looks like it uses a mono plug, so I don't know exactly how it communicates.
TIA, Rick
Sent via [email protected]. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
Hi, here is the link for the manual which has the schematic in it...
http://www.icom.co.jp/manual/external/transceivers/CT-17.pdf
it transmits and receives on the same line so you can get collisions
73 Kevin WA6FWF
----- Original Message ----- From: "Rick Mann" [email protected] To: "Amsat-Bb@Amsat. Org" [email protected] Sent: Wednesday, December 12, 2007 8:25 PM Subject: [amsat-bb] IC-910H C-IV control port pinout?
Does anyone have pinouts for the Icom IC-910H's C-IV port? I'm hoping to fashion a USB-to-serial adaptor for it, rather than buying Icom's expensive little box. I'm concerned, though, because it looks like it uses a mono plug, so I don't know exactly how it communicates.
TIA, Rick
Sent via [email protected]. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
Rick,
If you want to build your own CT-17 box, see www.cqham.ru/ci-v_icom.htm . I built the version by G3VGR which is near the back of the paper, and it works flawlessly between my old Compaq laptop and my IC-821 and IC-901.
73 de Gene WB2LLP ----- Original Message ----- From: "wa6fwf" [email protected] To: "Amsat-Bb@Amsat. Org" [email protected] Sent: Thursday, December 13, 2007 12:07 AM Subject: [amsat-bb] Re: IC-910H C-IV control port pinout?
Hi, here is the link for the manual which has the schematic in it...
http://www.icom.co.jp/manual/external/transceivers/CT-17.pdf
it transmits and receives on the same line so you can get collisions
73 Kevin WA6FWF
----- Original Message ----- From: "Rick Mann" [email protected] To: "Amsat-Bb@Amsat. Org" [email protected] Sent: Wednesday, December 12, 2007 8:25 PM Subject: [amsat-bb] IC-910H C-IV control port pinout?
Does anyone have pinouts for the Icom IC-910H's C-IV port? I'm hoping to fashion a USB-to-serial adaptor for it, rather than buying Icom's expensive little box. I'm concerned, though, because it looks like it uses a mono plug, so I don't know exactly how it communicates.
TIA, Rick
Sent via [email protected]. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected]. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
participants (4)
-
jonny 290 -
Rick Mann -
wa6fwf -
WB2LLP