SatPC32 and Yaesu FT-817nd not working properly
Hi All,
I've used SatPC32 with my Icom IC-910H successfully, I tried using SatPC32 with my Yaesu FT-817nd and ran into some problems tonight. I'm seeking setup and troubleshooting help..
*a) Anomalous Behavior of FT-817nd* Frequency does not change to satellite frequencies Frequency stays on 7 MHz On SatPC32 start up, mode on FT-817 changes from LSB to FM (in accordance with AO-27) Radio rapidly switches between VFOa and VFOb a couple times when I select different satellites Correct mode (CW/FM) seems to be chosen.
*b) FT-817nd notes* Factory reset performed CAT rate kept at 4800 Split mode is shown when SatPC32 is run I've tried two different FT-817nd's and they both exhibit this anomalous behavior.
*c) SatPC32 setup parameters worth mentioning* version 12.8d - fresh installation C+ i CAT control is ON A- automatic satellite chane OFF V- VFO mode OFF ..........<Radio Setup> parameters............ Radio 1 "Yaesu" Model FT-817 Baudrate 4800 (verified same as menu item #14 "CAT RATE" on FT-817nd) COM port - 7 (verified correct with Windows Device Manager. I plugged and unplugged the CAT cable and could see COM7 appear and disappear with the Windows Device Manager) CAT delay 110 no boxes checked: RTS+12, DTS+12, KCT-Tuner, Auto Sat Rx/Tx change, Satellite Mode Radio 2 none
*d) Reading the manual* I've read and followed the directions in the SatPC32 manual closely, including the 'Hints for Yaesu radio" file.
*e) Communications to Yaesu verified with another program* I verified the computer and CAT cable can communicate with the FT-817nd at least when using CHIRP. I was able to successfully program memory channels in both FT-871nd's..
*QUESTIONS* a) is there a known problem with using this version of SatPC32 with an FT-817nd? b) Any thoughts of additional troubleshooting steps I could take?
I suspect I just missed something in the setup manual, but I can't seem to figure out what. Thanks for any help you can provide.
Curt / K7ZOO
There are two versions of SatPC32 available for download for North American users
a) 128d_991 release date June 2019 b) 128d_Scope_Digi release date July 2020
SatPC32 version released June 2019 works properly with the FT-817nd. *SatPC32 version released July 2020 DOES NOT work properly with the FT-817nd.*
I'll forward a note to the author of the program (DK1TB) and make them aware of this issue.
73's,
Curt / K7ZOO
---------- Forwarded message --------- From: Curt Laumann curt.laumann@gmail.com Date: Wed, Dec 2, 2020 at 3:05 AM Subject: SatPC32 and Yaesu FT-817nd not working properly To: AMSAT-BB@amsat.org
Hi All,
I've used SatPC32 with my Icom IC-910H successfully, I tried using SatPC32 with my Yaesu FT-817nd and ran into some problems tonight. I'm seeking setup and troubleshooting help..
*a) Anomalous Behavior of FT-817nd* Frequency does not change to satellite frequencies Frequency stays on 7 MHz On SatPC32 start up, mode on FT-817 changes from LSB to FM (in accordance with AO-27) Radio rapidly switches between VFOa and VFOb a couple times when I select different satellites Correct mode (CW/FM) seems to be chosen.
*b) FT-817nd notes* Factory reset performed CAT rate kept at 4800 Split mode is shown when SatPC32 is run I've tried two different FT-817nd's and they both exhibit this anomalous behavior.
*c) SatPC32 setup parameters worth mentioning* version 12.8d - fresh installation C+ i CAT control is ON A- automatic satellite chane OFF V- VFO mode OFF ..........<Radio Setup> parameters............ Radio 1 "Yaesu" Model FT-817 Baudrate 4800 (verified same as menu item #14 "CAT RATE" on FT-817nd) COM port - 7 (verified correct with Windows Device Manager. I plugged and unplugged the CAT cable and could see COM7 appear and disappear with the Windows Device Manager) CAT delay 110 no boxes checked: RTS+12, DTS+12, KCT-Tuner, Auto Sat Rx/Tx change, Satellite Mode Radio 2 none
*d) Reading the manual* I've read and followed the directions in the SatPC32 manual closely, including the 'Hints for Yaesu radio" file.
*e) Communications to Yaesu verified with another program* I verified the computer and CAT cable can communicate with the FT-817nd at least when using CHIRP. I was able to successfully program memory channels in both FT-871nd's..
*QUESTIONS* a) is there a known problem with using this version of SatPC32 with an FT-817nd? b) Any thoughts of additional troubleshooting steps I could take?
I suspect I just missed something in the setup manual, but I can't seem to figure out what. Thanks for any help you can provide.
Curt / K7ZOO
participants (1)
-
Curt Laumann