Yes, after trying everything that I could think of with no luck, it occurred to me that I could dump the data that had been received previously (when "upload" was turned off) and replay my I/Q file once again into the Fox Telem software with "upload" turned on.
That worked, but only 4 packets uploaded even though the software indicated 10 decodes. Not sure why, but I was satisfied... I don't consider it a competition; I really just wanted to get completely through the process and actually have some data upload to the site.
I do have some observations that I'll share on the chance that it helps someone else.
While several bit rates are available in the Fox Telem software on a drop-down menu, the documentation recommends 48,000. So, before replaying my I/Q file that last time, I reconfigured SDR# as well as the VB-Cable audio link to both work at 48,000. Sure enough, I decoded many more packets than I had previously. Going forward I'll capture the data with those settings.
Last night's pass might have been unique in that it was a minute of slow-speed data but then transitioned to high-speed. So, I had to replay my I/Q file twice... once with the Fox Telem software set to slow data and again with it set to high. However, I realize now that I could have easily paused the playback in SDR#, stopped the Fox Telem input, switched to high speed, and resumed the playback.
Since I'm not going to have an internet connection during the initial data capture, it would appear that the correct sequence of events for my configuration will be to only use the Fox Telem software during a fly-over to give me some feedback as to how well I'm receiving. I'll then dump the resulting payload and replay the recorded I/Q file with an active internet connection and the Fox Telem software set to upload. It would be wonderful if the software would "store & forward" the packets once online, but this might be a blessing in disguise as there is every chance that I'll have a better result decoding under controlled conditions where I'm don't have my hands full with an antenna, etc.
Also, I see that many people with more advanced setups are able to play their recorded I/Q .wav files directly in the Fox Telem software. I did not have any success with that and I actually liked replaying my recordings in SDR# so that I could verify that I was centered on the carrier and make minor frequency adjustments. I was also tweaking output levels on replay. I didn't really know if there was any benefit in that, but I told myself that I was keeping the waveforms on the Fox Telem software as "clean" as possible in hopes of more decodes. Similar apps give some level feedback so you'll know if you are feeding it at the right volume, but it's still a really nice app.
At any rate, I was pretty tickled with any success at all and VERY appreciative of the information that others have shared.
In summary, my setup is:
-Arrow dual-band antenna (will test some future passes with omni QFH when elevation is high) -$20 RTL-SDR dongle -SDR# on Windows-7, FM-narrow @ 32k bandwidth with audio set to 48,000, doppler tracking from Orbitron -VB Cable set to 48,000 -Fox Telem software with AF input set to VB-Cable @ 48,000
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
----- Original Message ----- From: David G0MRF To: [email protected] Sent: Saturday, October 10, 2015 03:28 Subject: Re: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
Hi. There is a K4KDR-FM17 in the list with 4 somethings (frames payloads packets or whatever)
Thanks
David
-----Original Message----- From: Scott [email protected] To: amsat-bb [email protected] Sent: Sat, 10 Oct 2015 2:45 Subject: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
My Fox 1 Telemetry Analysis Tool is showing "Decoded: 8" and "Queued: 0" at the bottom of the screen.
I have my station details complete and the box to "Upload to Server" is checked.
Not seeing my call sign on the Leaderboard Statistics page, but I have no idea how long to wait before I should expect some feedback from an upload to be reflected on that page.
Is there some way to know when the Windows App has completed an upload successfully?
I have logging enabled and see a line as follows:
===== Trying Primary Server: tlm.amsat.org:41041 =====
... but no indication of a successful -or- failed upload. I do have an active internet connection.
Many thanks.
-Scott, K4KDR Montpelier, VA USA _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Hi !
With help from K4SQC I finally got some AO85 telemetry to decode! After the 186 payloads were decoded (high speed on that pass!) and the pass was complete I realized "upload to server" was not checked, so I checked it.
Is the information below accurate, the already decoded telemetry will not now or ever upload to the server? We did record the pass in HDSDR so I should be able to follow the path Scott took but I'd like to verify this before "dumping" the decodes.
Thanks!
*Daryl K4RGK
* On 10/10/2015 7:42 AM, Scott wrote:
Yes, after trying everything that I could think of with no luck, it occurred to me that I could dump the data that had been received previously (when "upload" was turned off) and replay my I/Q file once again into the Fox Telem software with "upload" turned on.
That worked, but only 4 packets uploaded even though the software indicated 10 decodes. Not sure why, but I was satisfied... I don't consider it a competition; I really just wanted to get completely through the process and actually have some data upload to the site.
I do have some observations that I'll share on the chance that it helps someone else.
While several bit rates are available in the Fox Telem software on a drop-down menu, the documentation recommends 48,000. So, before replaying my I/Q file that last time, I reconfigured SDR# as well as the VB-Cable audio link to both work at 48,000. Sure enough, I decoded many more packets than I had previously. Going forward I'll capture the data with those settings.
Last night's pass might have been unique in that it was a minute of slow-speed data but then transitioned to high-speed. So, I had to replay my I/Q file twice... once with the Fox Telem software set to slow data and again with it set to high. However, I realize now that I could have easily paused the playback in SDR#, stopped the Fox Telem input, switched to high speed, and resumed the playback.
Since I'm not going to have an internet connection during the initial data capture, it would appear that the correct sequence of events for my configuration will be to only use the Fox Telem software during a fly-over to give me some feedback as to how well I'm receiving. I'll then dump the resulting payload and replay the recorded I/Q file with an active internet connection and the Fox Telem software set to upload. It would be wonderful if the software would "store & forward" the packets once online, but this might be a blessing in disguise as there is every chance that I'll have a better result decoding under controlled conditions where I'm don't have my hands full with an antenna, etc.
Also, I see that many people with more advanced setups are able to play their recorded I/Q .wav files directly in the Fox Telem software. I did not have any success with that and I actually liked replaying my recordings in SDR# so that I could verify that I was centered on the carrier and make minor frequency adjustments. I was also tweaking output levels on replay. I didn't really know if there was any benefit in that, but I told myself that I was keeping the waveforms on the Fox Telem software as "clean" as possible in hopes of more decodes. Similar apps give some level feedback so you'll know if you are feeding it at the right volume, but it's still a really nice app.
At any rate, I was pretty tickled with any success at all and VERY appreciative of the information that others have shared.
In summary, my setup is:
-Arrow dual-band antenna (will test some future passes with omni QFH when elevation is high) -$20 RTL-SDR dongle -SDR# on Windows-7, FM-narrow @ 32k bandwidth with audio set to 48,000, doppler tracking from Orbitron -VB Cable set to 48,000 -Fox Telem software with AF input set to VB-Cable @ 48,000
----- Original Message ----- From: David G0MRF To: [email protected] Sent: Saturday, October 10, 2015 03:28 Subject: Re: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
Hi. There is a K4KDR-FM17 in the list with 4 somethings (frames payloads packets or whatever)
Thanks
David
-----Original Message----- From: Scott [email protected] To: amsat-bb [email protected] Sent: Sat, 10 Oct 2015 2:45 Subject: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
My Fox 1 Telemetry Analysis Tool is showing "Decoded: 8" and "Queued: 0" at the bottom of the screen.
I have my station details complete and the box to "Upload to Server" is checked.
Not seeing my call sign on the Leaderboard Statistics page, but I have no idea how long to wait before I should expect some feedback from an upload to be reflected on that page.
Is there some way to know when the Windows App has completed an upload successfully?
I have logging enabled and see a line as follows:
===== Trying Primary Server: tlm.amsat.org:41041 =====
... but no indication of a successful -or- failed upload. I do have an active internet connection.
Many thanks.
-Scott, K4KDR Montpelier, VA USA _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Daryl,
The below instructions will work, but you do not need to delete your data. Just replay the pass with upload to server on. FoxTelem will not store the duplicates locally, but it will queue them and upload them to the server. If your local count of payloads increases, then it means you managed to decode a few more frames.
73 Chris
On Thu, Oct 22, 2015 at 7:03 PM, Daryl Young [email protected] wrote:
Hi !
With help from K4SQC I finally got some AO85 telemetry to decode! After the 186 payloads were decoded (high speed on that pass!) and the pass was complete I realized "upload to server" was not checked, so I checked it.
Is the information below accurate, the already decoded telemetry will not now or ever upload to the server? We did record the pass in HDSDR so I should be able to follow the path Scott took but I'd like to verify this before "dumping" the decodes.
Thanks!
*Daryl K4RGK
On 10/10/2015 7:42 AM, Scott wrote:
Yes, after trying everything that I could think of with no luck, it occurred to me that I could dump the data that had been received previously (when "upload" was turned off) and replay my I/Q file once again into the Fox Telem software with "upload" turned on.
That worked, but only 4 packets uploaded even though the software indicated 10 decodes. Not sure why, but I was satisfied... I don't consider it a competition; I really just wanted to get completely through the process and actually have some data upload to the site.
I do have some observations that I'll share on the chance that it helps someone else.
While several bit rates are available in the Fox Telem software on a drop-down menu, the documentation recommends 48,000. So, before replaying my I/Q file that last time, I reconfigured SDR# as well as the VB-Cable audio link to both work at 48,000. Sure enough, I decoded many more packets than I had previously. Going forward I'll capture the data with those settings.
Last night's pass might have been unique in that it was a minute of slow-speed data but then transitioned to high-speed. So, I had to replay my I/Q file twice... once with the Fox Telem software set to slow data and again with it set to high. However, I realize now that I could have easily paused the playback in SDR#, stopped the Fox Telem input, switched to high speed, and resumed the playback.
Since I'm not going to have an internet connection during the initial data capture, it would appear that the correct sequence of events for my configuration will be to only use the Fox Telem software during a fly-over to give me some feedback as to how well I'm receiving. I'll then dump the resulting payload and replay the recorded I/Q file with an active internet connection and the Fox Telem software set to upload. It would be wonderful if the software would "store & forward" the packets once online, but this might be a blessing in disguise as there is every chance that I'll have a better result decoding under controlled conditions where I'm don't have my hands full with an antenna, etc.
Also, I see that many people with more advanced setups are able to play their recorded I/Q .wav files directly in the Fox Telem software. I did not have any success with that and I actually liked replaying my recordings in SDR# so that I could verify that I was centered on the carrier and make minor frequency adjustments. I was also tweaking output levels on replay. I didn't really know if there was any benefit in that, but I told myself that I was keeping the waveforms on the Fox Telem software as "clean" as possible in hopes of more decodes. Similar apps give some level feedback so you'll know if you are feeding it at the right volume, but it's still a really nice app.
At any rate, I was pretty tickled with any success at all and VERY appreciative of the information that others have shared.
In summary, my setup is:
-Arrow dual-band antenna (will test some future passes with omni QFH when elevation is high) -$20 RTL-SDR dongle -SDR# on Windows-7, FM-narrow @ 32k bandwidth with audio set to 48,000, doppler tracking from Orbitron -VB Cable set to 48,000 -Fox Telem software with AF input set to VB-Cable @ 48,000
----- Original Message ----- From: David G0MRF To: [email protected] Sent: Saturday, October 10, 2015 03:28 Subject: Re: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
Hi. There is a K4KDR-FM17 in the list with 4 somethings (frames payloads packets or whatever)
Thanks
David
-----Original Message----- From: Scott [email protected] To: amsat-bb [email protected] Sent: Sat, 10 Oct 2015 2:45 Subject: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
My Fox 1 Telemetry Analysis Tool is showing "Decoded: 8" and "Queued: 0" at the bottom of the screen.
I have my station details complete and the box to "Upload to Server" is checked.
Not seeing my call sign on the Leaderboard Statistics page, but I have no idea how long to wait before I should expect some feedback from an upload to be reflected on that page.
Is there some way to know when the Windows App has completed an upload successfully?
I have logging enabled and see a line as follows:
===== Trying Primary Server: tlm.amsat.org:41041 =====
... but no indication of a successful -or- failed upload. I do have an active internet connection.
Many thanks.
-Scott, K4KDR Montpelier, VA USA _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Hello Daryl. Hopefully someone with more knowledge that I have will reply, but it worked very well for me.
Don't forget that you can make a copy of your log folder before purging the data from inside the FoxTelem software so that you can put things back if you don't like the results after re-running the pass from your .WAV recording.
I'm not a programmer, but if it's do-able, I think it would be great if future versions of all the various cubesat telemetry applications have the ability to store a download and then upload it when the computer is back on an internet connection. Of course I realize that would add complexity since each packet would have to have a timestamp if it's not being uploaded in real time.
-Scott, K4KDR Montpelier, VA USA
--------------------------------------------------------------------------------
----- Original Message ----- From: Daryl Young To: [email protected] Sent: Thursday, October 22, 2015 19:03 Subject: Re: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
Hi !
With help from K4SQC I finally got some AO85 telemetry to decode! After the 186 payloads were decoded (high speed on that pass!) and the pass was complete I realized "upload to server" was not checked, so I checked it.
Is the information below accurate, the already decoded telemetry will not now or ever upload to the server? We did record the pass in HDSDR so I should be able to follow the path Scott took but I'd like to verify this before "dumping" the decodes.
Thanks!
*Daryl K4RGK
* On 10/10/2015 7:42 AM, Scott wrote:
Yes, after trying everything that I could think of with no luck, it occurred to me that I could dump the data that had been received previously (when "upload" was turned off) and replay my I/Q file once again into the Fox Telem software with "upload" turned on.
That worked, but only 4 packets uploaded even though the software indicated 10 decodes. Not sure why, but I was satisfied... I don't consider it a competition; I really just wanted to get completely through the process and actually have some data upload to the site.
I do have some observations that I'll share on the chance that it helps someone else.
While several bit rates are available in the Fox Telem software on a drop-down menu, the documentation recommends 48,000. So, before replaying my I/Q file that last time, I reconfigured SDR# as well as the VB-Cable audio link to both work at 48,000. Sure enough, I decoded many more packets than I had previously. Going forward I'll capture the data with those settings.
Last night's pass might have been unique in that it was a minute of slow-speed data but then transitioned to high-speed. So, I had to replay my I/Q file twice... once with the Fox Telem software set to slow data and again with it set to high. However, I realize now that I could have easily paused the playback in SDR#, stopped the Fox Telem input, switched to high speed, and resumed the playback.
Since I'm not going to have an internet connection during the initial data capture, it would appear that the correct sequence of events for my configuration will be to only use the Fox Telem software during a fly-over to give me some feedback as to how well I'm receiving. I'll then dump the resulting payload and replay the recorded I/Q file with an active internet connection and the Fox Telem software set to upload. It would be wonderful if the software would "store & forward" the packets once online, but this might be a blessing in disguise as there is every chance that I'll have a better result decoding under controlled conditions where I'm don't have my hands full with an antenna, etc.
Also, I see that many people with more advanced setups are able to play their recorded I/Q .wav files directly in the Fox Telem software. I did not have any success with that and I actually liked replaying my recordings in SDR# so that I could verify that I was centered on the carrier and make minor frequency adjustments. I was also tweaking output levels on replay. I didn't really know if there was any benefit in that, but I told myself that I was keeping the waveforms on the Fox Telem software as "clean" as possible in hopes of more decodes. Similar apps give some level feedback so you'll know if you are feeding it at the right volume, but it's still a really nice app.
At any rate, I was pretty tickled with any success at all and VERY appreciative of the information that others have shared.
In summary, my setup is:
-Arrow dual-band antenna (will test some future passes with omni QFH when elevation is high) -$20 RTL-SDR dongle -SDR# on Windows-7, FM-narrow @ 32k bandwidth with audio set to 48,000, doppler tracking from Orbitron -VB Cable set to 48,000 -Fox Telem software with AF input set to VB-Cable @ 48,000
----- Original Message ----- From: David G0MRF To: [email protected] Sent: Saturday, October 10, 2015 03:28 Subject: Re: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
Hi. There is a K4KDR-FM17 in the list with 4 somethings (frames payloads packets or whatever)
Thanks
David
-----Original Message----- From: Scott [email protected] To: amsat-bb [email protected] Sent: Sat, 10 Oct 2015 2:45 Subject: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
My Fox 1 Telemetry Analysis Tool is showing "Decoded: 8" and "Queued: 0" at the bottom of the screen.
I have my station details complete and the box to "Upload to Server" is checked.
Not seeing my call sign on the Leaderboard Statistics page, but I have no idea how long to wait before I should expect some feedback from an upload to be reflected on that page.
Is there some way to know when the Windows App has completed an upload successfully?
I have logging enabled and see a line as follows:
===== Trying Primary Server: tlm.amsat.org:41041 =====
... but no indication of a successful -or- failed upload. I do have an active internet connection.
Many thanks.
-Scott, K4KDR Montpelier, VA USA _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Delfi-C3 RASCAL does that, and its now in its 7th+ year in space.
Also, the FUNcube dashboard can do it, albeit in a slightly convoluted way if you close the program in between. (Save the pass and replay it when you have an internet connection) If you leave the program running and restore the internet connection it will automatically pick up where it left off.
I am sure many other telemetry clients will have similar features, that may or may not be obvious to the user.
Wouter PA3WEG
On Fri, Oct 23, 2015 at 6:07 PM, Scott [email protected] wrote:
Hello Daryl. Hopefully someone with more knowledge that I have will reply, but it worked very well for me.
Don't forget that you can make a copy of your log folder before purging the data from inside the FoxTelem software so that you can put things back if you don't like the results after re-running the pass from your .WAV recording.
I'm not a programmer, but if it's do-able, I think it would be great if future versions of all the various cubesat telemetry applications have the ability to store a download and then upload it when the computer is back on an internet connection. Of course I realize that would add complexity since each packet would have to have a timestamp if it's not being uploaded in real time.
-Scott, K4KDR Montpelier, VA USA
----- Original Message ----- From: Daryl Young To: [email protected] Sent: Thursday, October 22, 2015 19:03 Subject: Re: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been Uploaded?
Hi !
With help from K4SQC I finally got some AO85 telemetry to decode! After the 186 payloads were decoded (high speed on that pass!) and the pass was complete I realized "upload to server" was not checked, so I checked it.
Is the information below accurate, the already decoded telemetry will not now or ever upload to the server? We did record the pass in HDSDR so I should be able to follow the path Scott took but I'd like to verify this before "dumping" the decodes.
Thanks!
*Daryl K4RGK
On 10/10/2015 7:42 AM, Scott wrote:
Yes, after trying everything that I could think of with no luck, it
occurred to me that I could dump the data that had been received previously (when "upload" was turned off) and replay my I/Q file once again into the Fox Telem software with "upload" turned on.
That worked, but only 4 packets uploaded even though the software
indicated 10 decodes. Not sure why, but I was satisfied... I don't consider it a competition; I really just wanted to get completely through the process and actually have some data upload to the site.
I do have some observations that I'll share on the chance that it
helps someone else.
While several bit rates are available in the Fox Telem software on a
drop-down menu, the documentation recommends 48,000. So, before replaying my I/Q file that last time, I reconfigured SDR# as well as the VB-Cable audio link to both work at 48,000. Sure enough, I decoded many more packets than I had previously. Going forward I'll capture the data with those settings.
Last night's pass might have been unique in that it was a minute of
slow-speed data but then transitioned to high-speed. So, I had to replay my I/Q file twice... once with the Fox Telem software set to slow data and again with it set to high. However, I realize now that I could have easily paused the playback in SDR#, stopped the Fox Telem input, switched to high speed, and resumed the playback.
Since I'm not going to have an internet connection during the initial
data capture, it would appear that the correct sequence of events for my configuration will be to only use the Fox Telem software during a fly-over to give me some feedback as to how well I'm receiving. I'll then dump the resulting payload and replay the recorded I/Q file with an active internet connection and the Fox Telem software set to upload. It would be wonderful if the software would "store & forward" the packets once online, but this might be a blessing in disguise as there is every chance that I'll have a better result decoding under controlled conditions where I'm don't have my hands full with an antenna, etc.
Also, I see that many people with more advanced setups are able to
play their recorded I/Q .wav files directly in the Fox Telem software. I did not have any success with that and I actually liked replaying my recordings in SDR# so that I could verify that I was centered on the carrier and make minor frequency adjustments. I was also tweaking output levels on replay. I didn't really know if there was any benefit in that, but I told myself that I was keeping the waveforms on the Fox Telem software as "clean" as possible in hopes of more decodes. Similar apps give some level feedback so you'll know if you are feeding it at the right volume, but it's still a really nice app.
At any rate, I was pretty tickled with any success at all and VERY
appreciative of the information that others have shared.
In summary, my setup is:
-Arrow dual-band antenna (will test some future passes with omni QFH
when elevation is high)
-$20 RTL-SDR dongle -SDR# on Windows-7, FM-narrow @ 32k bandwidth with audio set to
48,000, doppler tracking from Orbitron
-VB Cable set to 48,000 -Fox Telem software with AF input set to VB-Cable @ 48,000
----- Original Message ----- From: David G0MRF To: [email protected] Sent: Saturday, October 10, 2015 03:28 Subject: Re: [amsat-bb] How to Know When Your AO-85 Telemetry Has
Been Uploaded?
Hi. There is a K4KDR-FM17 in the list with 4 somethings (frames
payloads packets or whatever)
Thanks
David
-----Original Message----- From: Scott [email protected] To: amsat-bb [email protected] Sent: Sat, 10 Oct 2015 2:45 Subject: [amsat-bb] How to Know When Your AO-85 Telemetry Has Been
Uploaded?
My Fox 1 Telemetry Analysis Tool is showing "Decoded: 8" and "Queued:
0" at
the bottom of the screen.
I have my station details complete and the box to "Upload to Server" is checked.
Not seeing my call sign on the Leaderboard Statistics page, but I have no idea how long to wait before I should expect some feedback from an upload to be reflected on that page.
Is there some way to know when the Windows App has completed an upload successfully?
I have logging enabled and see a line as follows:
===== Trying Primary Server: tlm.amsat.org:41041 =====
... but no indication of a successful -or- failed upload. I do have an active internet connection.
Many thanks.
-Scott, K4KDR Montpelier, VA USA _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership.
Opinions expressed
are solely those of the author, and do not reflect the official views
of AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
-
Chris Thompson -
Daryl Young -
Scott -
Wouter Weggelaar