Hi folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on!
Please see below for all FUNcube mission info
73s Graham G3VZV and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Hi folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on!
Please see below for all FUNcube mission info
73s Jim G3WGM and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Hi folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on! Plan as usual is to revert to auto switching mode on Sunday PM.
Please see below for all FUNcube mission info
73s Jim G3WGM and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Hi folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on! Plan as usual is to revert to auto switching mode on Sunday PM.
Please see below for all FUNcube mission info
73s Jim G3WGM and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Hi folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on!
Please note that the transponder will remain on longer than usual (probably until Monday evening UTC) in support of Barry ARS and their contribution to the event at the Royal Mint in Wales. Moe info at http://www.bars.btck.co.uk/News
Please see below for all FUNcube mission info
73s Jim G3WGM and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
HI folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on!
As normal, plan is to revert to normal mode on Sun PM (UTC).
Please see below for all FUNcube mission info
73s Jim G3WGM and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Hi Folks,
Slight change of plan. We now propose the keep the transponder on full time all week next week. This is to support operations from YOTA and also because the schools (at least those in UK) are on holiday.
73s Jim G3WGM for FUNcube Ops Team.
-----Original Message----- From: Jim Heck G3WGM Sent: Friday, August 04, 2017 9:21 PM To: AMSAT ; [email protected] Subject: Re: [amsat-bb] AO73 Mode change
HI folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on!
As normal, plan is to revert to normal mode on Sun PM (UTC).
Please see below for all FUNcube mission info
73s Jim G3WGM and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
HI folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on!
As normal, plan is to revert to normal mode on Sun PM (UTC).
Please see below for all FUNcube mission info
73s Jim G3WGM and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected]rg. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Hi Folks,
I dont own an Alexa, but some (non ham radio) friends of mine got one for Christmas and we have been experimenting!
It occurred to me that it would be great to be able to ask Alexa "Alexa, when is the next pass of AO-85" Or even better "Alexa, notify me 5 minutes before the next pass of AO-73".
I wonder if anyone has tried (and succeeded) in doing this?
HNY Jim G3WGM
You do like set a challenge :-)
I have an end point that I could modify for Alexa.
Actually I had thought about it a while ago.
Dave
Sent from my iPhone
On 29 Dec 2018, at 12:38, Jim Heck [email protected] wrote:
Hi Folks,
I dont own an Alexa, but some (non ham radio) friends of mine got one for Christmas and we have been experimenting!
It occurred to me that it would be great to be able to ask Alexa "Alexa, when is the next pass of AO-85" Or even better "Alexa, notify me 5 minutes before the next pass of AO-73".
I wonder if anyone has tried (and succeeded) in doing this?
HNY Jim G3WGM _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
what I was thinking of doing was somehow link gpredict and the features of the AstroPi LED matrix to make it scroll when a satellite is overhead. I have the idea, not the skillset. The Alexa has better potential, and I would love to see that implemented. -Kevin (KK4YEL)
On Sat, Dec 29, 2018 at 9:03 AM David Johnson [email protected] wrote:
You do like set a challenge :-)
I have an end point that I could modify for Alexa.
Actually I had thought about it a while ago.
Dave
I'm game to support Google Home, I can only ask mine about solar weather :)
Peter 2M0SQL
On Sat, 29 Dec 2018, 14:03 David Johnson <[email protected] wrote:
You do like set a challenge :-)
I have an end point that I could modify for Alexa.
Actually I had thought about it a while ago.
Dave
Sent from my iPhone
On 29 Dec 2018, at 12:38, Jim Heck [email protected] wrote:
Hi Folks,
I dont own an Alexa, but some (non ham radio) friends of mine got one
for Christmas and we have been experimenting!
It occurred to me that it would be great to be able to ask Alexa "Alexa,
when is the next pass of AO-85" Or even better "Alexa, notify me 5 minutes before the next pass of AO-73".
I wonder if anyone has tried (and succeeded) in doing this?
HNY Jim G3WGM _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership.
Opinions expressed
are solely those of the author, and do not reflect the official views of
AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
It sounds like something that could be built with IFTTT without too much effort.
On Sat, Dec 29, 2018 at 10:52 AM Peter Goodhall (2M0SQL) < [email protected]> wrote:
I'm game to support Google Home, I can only ask mine about solar weather :)
Peter 2M0SQL
On Sat, 29 Dec 2018, 14:03 David Johnson <[email protected] wrote:
You do like set a challenge :-)
I have an end point that I could modify for Alexa.
Actually I had thought about it a while ago.
Dave
Sent from my iPhone
On 29 Dec 2018, at 12:38, Jim Heck [email protected] wrote:
Hi Folks,
I dont own an Alexa, but some (non ham radio) friends of mine got one
for Christmas and we have been experimenting!
It occurred to me that it would be great to be able to ask Alexa
"Alexa,
when is the next pass of AO-85" Or even better "Alexa, notify me 5
minutes
before the next pass of AO-73".
I wonder if anyone has tried (and succeeded) in doing this?
HNY Jim G3WGM _______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership.
Opinions expressed
are solely those of the author, and do not reflect the official views
of
AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership.
Opinions
expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite
program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
I can’t find it right now, but I remember seeing on thingiverse a three tier LED stand controlled by a raspberry pi that tracked satellites. Don’t remember the software but I’ll keep looking.
Dan
-- Sent from my iPhone. Please pardon any mispelings or errors.
Hi Folks
After evaluating the transponder now that the satellite temperatures are returning to normal, we plan to resume transponder operations from the coming weekend. The transponder will be left on continuously next week 24/7. We would appreciate reports of transponder activity to [email protected]
73s Jim G3WGM
HI folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on!
As normal, plan is to revert to normal mode on Sun PM (UTC).
Please see below for all FUNcube mission info
73s Jim G3WGM and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
_______________________________________________ Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
HI folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on! As normal, plan is to revert to normal mode on Sun PM (UTC).
Please see below for all FUNcube mission info
73s Wouter PA3WEG and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space BV, The Netherlands.
On Fri, Sep 1, 2017 at 11:03 PM, Jim Heck G3WGM [email protected] wrote:
HI folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on!
As normal, plan is to revert to normal mode on Sun PM (UTC).
Please see below for all FUNcube mission info
73s Jim G3WGM and the FUNcube team.
++++++++++++++++++++++++++++++++++ FUNcube frequencies and other details ++++++++++++++++++++++++++++++++++
AO-73 FUNcube-1
The transponder is normally operational only when the satellite is in eclipse, ie the solar panels are NOT being illuminated. During weekends (from pm Fridays UTC to PM Sundays UTC) the transponder is operational 24/7.
When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. During holidays, eg Christmas, New Year, Easter, etc, the transponder maybe activated for extended periods. Watch AMSAT-BB for announcements which are usually made on Friday evenings (UTC)
The nominal transponder frequencies are:
Uplink: 435.150 - 435.130 MHz LSB (Inverting) Downlink: 145.950 - 145.970 MHz USB Telemetry Tx: 145.935 MHz BPSK
(The passband may be up to 15kHz higher depending on on-board temps. Lower temperatures give higher freqs!)
FUNcube-2 (aka FUNcube on UKube)
The FUNcube-2 sub-system continues to operate autonomously and, almost continuously, in amateur mode. The transponder is operational and the telemetry downlink is functioning with about 70mW output. The FUNcube-1 Dashboard does not correctly display the telemetry but it does correctly decode the data and uploads it to the FUNcube Data Warehouse from where it can be examined. Most of the real time data channels are operational and these include battery voltages, temperatures and ADCS data coming via the main On Board Computer (OBC).
The transponder is interrupted for a few seconds every 2 minutes when the other transmitter sends its CW beacon and, occasionally, for a few seconds when the main OBC reboots (approx seven times each orbit).
The nominal transponder frequencies are: Uplink: 435.080 - 435.060 MHz LSB (Inverting) Downlink: 145.930 - 145.950 MHz USB Telemetry Tx: 145.915 MHz BPSK
(The passband may be up to 10kHz higher depending on on-board temps. Low temperatures give higher freqs!)
EO79 FUNcube-3 Due to power budget constraints the transponder cannot be operational 24/7 and an orbit specific schedule has been developed. The transponder will commence operation 27 minutes after the spacecraft enters sunlight and will stay on for a period of 25 minutes. This schedule may be modified in future months as a result of experience.
The nominal transponder frequencies are: Uplink: 435.0723-435.0473 MHz LSB (Inverting) Downlink: 145.946-145.971 MHz USB
Further detailed info on EO79 transponder frequencies is at: https://amsat-uk.org/2016/11/10/eo79-funcube-3-transponder-commences-regular...
EO88/Nayif-1/FUNcube-5
EO88 is presently operating in autonomous mode. The transponder is operational when the satellite is in eclipse, ie the solar panels are NOT being illuminated. When the transponder is switched off, the telemetry beacon is on full power, when the transponder is on the beacon it is on low power. The transponder frequencies are:
Uplink: 435.045 – 435.015 MHz LSB (inverting) Downlink: 145.960-145.990 MHz USB Telemetry Tx: 145.940MHz
All FUNcube transponders are sponsored by AMSAT-UK and AMSAT-NL. We are very grateful for the assistance given by Innovative Solution In Space Bv, The Netherlands.
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via AMSAT[email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Sent via [email protected] AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Hi folks,
AO73/FUNcube is now in amateur mode for the weekend with the transponder on! Plan as normal is to switch back to auto switching mode on Sun pm UTC
73s Jim G3WGM and the FUNcube team.
-
Alex Free - N7AGF -
Daniel Holmes -
David Johnson -
Graham Shirville -
Jim Heck -
Jim Heck G3WGM -
Kevin Zari -
Peter Goodhall (2M0SQL) -
Wouter Weggelaar