Well, I got a shipping notice and a tracking number. The tracking number does not yet register with UPS though. I continue to say "we'll see". 73,
Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*
On Fri, Dec 8, 2023 at 11:58 AM Jim McCullers via pacsat-dev < pacsat-dev@amsat.org> wrote:
The last thing I ordered from Newark was also shipped from the UK with no shipping communications and as I recall took a long time.
It was also an obsolete component by DigiKey and Mouser.
Keep us posted.
Jim
Ok, Bob. The picture sure looks like there are "holes" there, but you never know. I do think that I asked Zach to put the connector on the bottom so it would line the ribbon cable up correctly with the RTIHU connector. We'll find out. BTW, Newark says they are sending the board from the UK. Hmm.
73,
Burns Fisher, WB1FJ
*AMSAT**(R) **Engineering -- Flight Software*
On Fri, Dec 8, 2023 at 11:00 AM Bob Stricklin via pacsat-dev < pacsat-dev@amsat.org> wrote:
Burns,
I believe he is talking about a 10 pin connector on the bottom left corner of the photo that is turned down below the board.
He probably did this to make a standard ribbon cable work with female IDC connectors on each end.
We can make that change if the boards are shipped.
It may be that Newark inventory is there because they do not got so much business on TI product. Normally when an OEM drops a product they pull all the distributor inventory back. These may be a third party board which is fine if they have the same processor and code.
It will be interesting to see if the TI ARM processor TM4C1294NCPDTT3R is on these boards. If it is and several people working on AMSAT projects need these boards we probably should buy more.
The info I have is the design information I showed last night that Zach shared with me on an AMSAT version of this programming interface board.
Bob
On Dec 8, 2023, at 9:41 AM, Burns Fisher (AMSAT) via pacsat-dev < pacsat-dev@amsat.org> wrote:
Thanks, Zach. That might mean that what I ordered is different. See in the picture, the place where you added the connector is not populated. (You have to hover over it to get the expanded version in order to see it).
https://www.newark.com/texas-instruments/cc-devpack-debug/debugger-devpak-si...
Well see what happens. Actually do you have a couple of male connectors that you could send me? That way, I could easily add it in and test the new board (assuming it comes...maybe you'd better wait until I get a shipping number :-) )
73,
Burns Fisher, WB1FJ
*AMSAT**(R) **Engineering -- Flight Software*
On Fri, Dec 8, 2023 at 10:32 AM Zach Metzinger zmetzing@pobox.com wrote:
On 12/8/23 08:07, Burns Fisher (AMSAT) wrote:
Note to Pacsat folks: It appears (and Zach can confirm) that Zach must have just ADDED a connector into a DNP space on the board...this is based on the pictures.
Hello Burns and the Pacsat team,
This is not correct; I replace the female 2x5 connector with a male 2x5 shrouded/keyed connector. Instructions, already sent to Bob Strickland, attached.
73,
--- Zach N0ZGO
pacsat-dev mailing list -- pacsat-dev@amsat.org View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org To unsubscribe send an email to pacsat-dev-leave@amsat.org Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org
pacsat-dev mailing list -- pacsat-dev@amsat.org View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org To unsubscribe send an email to pacsat-dev-leave@amsat.org Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org
pacsat-dev mailing list -- pacsat-dev@amsat.org View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org To unsubscribe send an email to pacsat-dev-leave@amsat.org Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org