Oh, I see.  So this is saying that I2c in general is ok, but that the temp sensor near the CPU is not working for whatever reason (bad bus connection, bad address bit connection, or bad chip).

And regarding the MRAM, I have the chip select wrong on at least one of those MRAM devices.  I just found that earlier and did not push it up to the repository..  Let me check what else I have done since I pushed upstream, and if all is ok, I'll push this change too.  Looks like most everything in the MRAM is ok otheriwise (whew!  Was driving me crazy)

I see you sent something else.  Have not seen it yet but will send this.

73,

Burns Fisher, WB1FJ
AMSAT(R) Engineering -- Flight Software


On Mon, Feb 5, 2024 at 4:43 PM Burns Fisher (AMSAT) <wb1fj@fisher.cc> wrote:
Ok, looks like two of the MRAMs are ok, and two are not for whatever reason.   Oh, I bet I know...I think I got the chip select lines wrong on one or two of them.  Funny the temp actually looks ok despite the error.    In the middle of checking something else.  Will get back after a bit more testing.
73,

Burns Fisher, WB1FJ
AMSAT(R) Engineering -- Flight Software


On Mon, Feb 5, 2024 at 4:41 PM Bob Stricklin via pacsat-dev <pacsat-dev@amsat.org> wrote:
Pacsat>
Pacsat>get mram sr
MRAM0: status 32, MRAM1: status ff
MRAM2: status 2, MRAM3: status ff
Pacsat>get temp
CPU Temp request failed
  Transmitter temp: 99 ( 29.5 degrees C)
Pacsat>


From: Burns Fisher (AMSAT) <wb1fj@fisher.cc>
Sent: Monday, February 5, 2024 3:35 PM
To: Bob Stricklin <bstrick@n5brg.com>
Cc: Bill via pacsat-dev <pacsat-dev@amsat.org>
Subject: Re: [pacsat-dev] One board now talking
 
Oh, I just sent you a mail before seeing this.

Wow!  Looks like there may be something wrong with my board.  Could you do "get mram sr" please?  You could try "get temp" also.

I'm not sure if those are the right values for the DCT (the AX5043).  I know I had a quick way at one point that I could tell if one particular register was correct.  I'll see if I can find it.

73,

Burns Fisher, WB1FJ
AMSAT(R) Engineering -- Flight Software


On Mon, Feb 5, 2024 at 4:24 PM Bob Stricklin via pacsat-dev <pacsat-dev@amsat.org> wrote:
After getting TX and RX connected correctly now working. Do not know what the correct report back is but here is some checks...

This board has four 4Mb MRAMs installed. 


Pacsat>get version

AMSAT-NA PacSat Console
Flight Software X0.1k (built on Feb  4 2024 at 21:53:10)
Compiled *RELEASE*
**X, E, U, or DEBUG Version: Not configured for flight**
Watchdog NOT Enabled
Using FreeRTOS withOUT premption enabled;
Free heap size is 75504
Flash memory size 1Mb+0Kb
MRAM config data partition size=1008, file system size=1047568
Pacsat>>get version

AMSAT-NA PacSat Console
Flight Software X0.1k (built on Feb  4 2024 at 21:53:10)
Compiled *RELEASE*
**X, E, U, or DEBUG Version: Not configured for flight**
Watchdog NOT Enabled
Using FreeRTOS withOUT premption enabled;
Free heap size is 75504
Flash memory size 1Mb+0Kb
MRAM config data partition size=1008, file system size=1047568
Pacsat>

Pacsat>get RSSI
RSSI is -64 dBm
Pacsat>

Pacsat>get ax
AX5043 dev 1 TX:
 FIFOSTAT: 00
 PWRMODE:: 77
 XTALCAP: 119
 PLLLOOP: 77
 PLLCPI: 77
 PLLVCOI: 77
 PLLRANGINGA: 77
 PLLVCODIV: 77
 FREQ 1911466666 Hz
 MODULATION: 77
 TXPWRCOEFFB0: 77
 TXPWRCOEFFB1: 77

AX5043 dev 0 RX:
 FIFOSTAT: 00
 PWRMODE: 67
 XTALCAP: 103
 PLLLOOP: 67
 PLLCPI: 67
 PLLVCOI: 67
 PLLRANGINGA: 67
 PLLVCODIV: 67
 FREQ 1654462744 Hz
 MODULATION: 67
 TXPWRCOEFFB0: 67
 TXPWRCOEFFB1: 67
Pacsat>




-----------------------------------------------------------

pacsat-dev mailing list -- pacsat-dev@amsat.org
View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org
To unsubscribe send an email to pacsat-dev-leave@amsat.org
Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org

-----------------------------------------------------------

pacsat-dev mailing list -- pacsat-dev@amsat.org
View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org
To unsubscribe send an email to pacsat-dev-leave@amsat.org
Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org