I think Jim was experimenting with weather miso needed a resistor. I think they can both be just jumped. Jim???
On Tue, May 9, 2023 at 12:28 PM Corey Minyard minyard@acm.org wrote:
It could be the serial port, that makes some sense, I guess.
I installed a jumper feeding 3.3v on J4 pin 1, and the MRAM still works, but the 5043s still don't.
I think I found it. R10 and R11 are not populated. One of them says 330 ohms, one says zero. What needs to be put here? I think I have some SM resistors, but probably 0603, and these look smaller.
-corey
Ok, I got both mails. One thing I notice is that there is some backflow
of
power from the serial line which lights the LED (dimly) even if the LaunchPad is unpowered. Could that be the reason for the 2.7V? I have those jumpers installed on both halves of the board, but I'm surprised
the
MRAM works at all if you don't have it installed (maybe that 2.7V is enough---and I don't see how that relates to the 5043).
On Tue, May 9, 2023 at 9:41 AM Corey Minyard minyard@acm.org wrote:
I send this from my acm.org account and realised it's not going to get to the pacsat mailing list. So here it is again.
On Tue, May 9, 2023 at 9:39 AM Corey Minyard minyard@acm.org wrote:
On Tue, May 09, 2023 at 09:28:06AM -0400, Burns Fisher (AMSAT) wrote:
Ok, glad the MRAM is working. Any chance that you don't have the two jumpers on the LaunchPad required to power the 5043s? These would
be a
pair on the right (components up, USB down, I think) just below the
bottom
set of pins.
Yes, the two jumpers labeled +5V and +3V3 right by J1 are both
installed.
I'm getting 3.3V on J1 pin 1 and 5V on J1 pin 2.
There are unpopulated jumpers on the LaunchPad by J4 (J6 on the Laumchpad) that have the same labels. I'm getting 2.7V on J4 pin 1, which is strange. That's what powers the MRAMs and the temperature sensor.
Should I put a jumper on 3V3 by J4? I'm getting 3.3V on the other side of the jumper. I'm wondering if the power is somehow coming through
the
5043s and getting to the MRAMs, but I don't see how that could happen.
BTW, I don't even try to push Jim's board all the way on. It is
tight as
it is and I want to be able to get it back off (relatively) easily.
But
regardess, the tops of the pins are all level, even though the newly soldered pins have a plastic holder at the bottom and the original
pins do
not.
Yeah, strange. I didn't notice until I tried to put the board on. My board now looks terrible, but it seems to be making good contact now.
I looked at close-up pictures on TI's web site, and the pins I had look the same as the ones in the picture.
-corey
73,
Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*
On Mon, May 8, 2023 at 11:52 PM Corey Minyard via pacsat-dev < pacsat-dev@amsat.org> wrote:
Burns sent me the info on that. I ran J5 pin 12 to a via on the bottom right of U1. After doing that wiring change, all but one
MRAM
appears to be working. It looks like R5 got removed somehow, I may have done that removing the wire. I just installed a bridge there, since it's a zero-ohm resistor, and the mram seems to be working
now.
The temperature sensor on the daughter board seems to be working.
I don't think the 5043's are working. I'm not getting anything on transmit, and I eventually get:
Pacsat>send pb status ## SELF TEST: pb_test_status TX QUEUE FULL: Could not add UI frame to Packet Queue PB Empty. ## PASSED SELF TEST: pb_test_status
after running that a few times. At startup, I'm getting:
ERROR: In start_rx, axradio_init returned: 5 ERROR: In start_tx, axradio_init_70cm returned: 5Initializing PB
Task
ERROR: Failed in init PB Status Timer
-corey
On Mon, May 8, 2023 at 9:51 PM Jim McCullers via pacsat-dev pacsat-dev@amsat.org wrote:
Chris,
Please take a look at the email I sent out earlier. There is the possibility of a wiring error on the board with my
white
wire correction.
As for the connectors being longer, I never noticed that and
these
should be the same connectors I sent Burns and Chris.
Burns say the MRAM is working after the wiring change and the
AX5043s
are working for Chris and Burns so not certain there.
Attached is the revised schematic. I'll have the Kicad files on
github
hopefully tomorrow. Have a couple of issues to deal with.
Jim McCullers WA4CWI
I sent this earlier, but just to Chris.
I got my board today and soldered on the connectors. Looking at
the
board now, I see that the connectors that came with the launchpad
are
around 1cm longer than the ones Jim supplied. I can't get the
mram or
ax5043s to be detected. I don't think it's making good contact on
the
connectors, for obvious reasons. Do I need to trim the old
connector, or
did I do something wrong?
I clipped the pins, and still no help. The power light by the
serial
connector works, and the serial port works. But the mrams and the
ax5043's
are not there.
I can't find the schematics in the git repository. PacSatDocs, I
assume. I guess I need to start debugging to figure out what is
wrong.
-corey
pacsat-dev mailing list -- pacsat-dev@amsat.org View archives of this mailing list at
https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org
To unsubscribe send an email to pacsat-dev-leave@amsat.org Manage all of your AMSAT-NA mailing list preferences at
pacsat-dev mailing list -- pacsat-dev@amsat.org View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org To unsubscribe send an email to pacsat-dev-leave@amsat.org Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org