Used a hot air with board held in vice. Lightly tug on the connector from bottom side while heating the pin solder side with 400 C hot air.
Then put flux on the for pins and used solder wick and a soldering iron to remove solder and most pin holes opened up.
On holes that do not open I use a dental explore tool to stick it hole when solder is melted. Remove iron and then take dental tool out.
Then solder in new connector.
I can do more for you if you want me to.
I forgot to clean the flux off the board I am sending back. You can use isopropyl alcohol to do this. I usually use Everclear or Ethel alcohol which leaves no white residue.
Bob
On Jan 9, 2024, at 12:06 PM, Burns Fisher (AMSAT) via pacsat-dev [email protected] wrote:
--===============0108675984297293611== Content-Type: multipart/alternative; boundary="00000000000059bbda060e872bbb"
--00000000000059bbda060e872bbb Content-Type: text/plain; charset="UTF-8" Content-Transfer-Encoding: quoted-printable
Thanks Bob. I now have the parts, but have had nothing but trouble both removing and replacing those dumb little connectors! Any hints? Are you using hot air or a small iron?
73,
Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*
On Tue, Jan 9, 2024 at 1:04=E2=80=AFPM Bob Stricklin via pacsat-dev < [email protected]> wrote:
I received the two Devpack programming boards from Burns. Replaced connectors on both boards and I have tested them on the Quad board and th=
ey
both worked fine.
Returning one of these to Burns today.
Bob
On Jan 5, 2024, at 11:21 AM, Burns Fisher (AMSAT) via pacsat-dev < [email protected]> wrote:
I included a little extra. The connectors that I had ordered just arrive=
d
(hot off the plane from Singapore) and I realized that Newark Electroncis had apparently switched the part number around on me, and they were surfa=
ce
mount! Not useful for me in this case, but if they are useful for anythi=
ng
you build, I sent you a few. 73,
Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*
On Fri, Jan 5, 2024 at 11:28=E2=80=AFAM Bob Stricklin via pacsat-dev < [email protected]> wrote:
Thank you sir.
Bob
On Jan 5, 2024, at 10:09=E2=80=AFAM, Burns Fisher (AMSAT) via pacsat-dev=
<
[email protected]> wrote:
=EF=BB=BF BTW, I'm putting both in the same box but including all the instructions that came with it. Note that the instructions assume you are going to b=
e
using this with a thing called a SensorTag so you can ignore them :-)
I don't care which one you return to be with the connector replace, btw.
Good luck!
73,
Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*
On Fri, Jan 5, 2024 at 10:59=E2=80=AFAM Burns Fisher (AMSAT) <wb1fj@fish=
er.cc>
wrote:
Bob, et al:
FWIW, the official name of the little boards I'm send is TI Simplelink SensorTag Devpack.
I'm including a photo of the one that works. You can see when you look at a new one) that the replacement connector goes on the opposite side =
of
the board from the existing 10-pin connector. The existing one is fema=
le
with no key. The new one is male with shroud and key. The key is on t=
he
outside edge of the board, and the connector is on the opposite side of=
the
board from the chip (on the same side as the larger connector.
I tried to load code using it (despite not being connect to the RTIHU) and got the attached error message. I used the xdsdfu utility that the error talks about and discovered this:
./ti/ccs1020/ccs/ccs_base/common/uscif/xds110/xdsdfu -e
USB Device Firmware Upgrade Utility Copyright (c) 2008-2019 Texas Instruments Incorporated. All rights reserved.
Scanning USB buses for supported XDS110 devices... <<<< Device 0 >>>> VID: 0x0451 PID: 0xbef3 Device Name: XDS110 with CMSIS-DAP Version: 2.2.5.1 Manufacturer: Texas Instruments Serial Num: L787 Mode: Runtime Configuration: Standard Found 1 device.
Notice the serial number L787. One of my working ones has the serial number L3122222. So letter L and 7 digits. I am setting yours to L31444444 and L31555555. Like this:
bfisher@skylab:~$ ./ti/ccs1020/ccs/ccs_base/common/uscif/xds110/xdsdfu -m USB Device Firmware Upgrade Utility Copyright (c) 2008-2019 Texas Instruments Incorporated. All rights reserved. Scanning USB buses for supported XDS110 devices... <<<< Device 0 >>>> VID: 0x0451 PID: 0xbef3 Device Name: XDS110 with CMSIS-DAP Version: 2.2.5.1 Manufacturer: Texas Instruments Serial Num: L787 Mode: Runtime Configuration: Standard Switching device into DFU mode.
bfisher@skylab:~$ ./ti/ccs1020/ccs/ccs_base/common/uscif/xds110/xdsdfu -s L3144444 -r USB Device Firmware Upgrade Utility Copyright (c) 2008-2019 Texas Instruments Incorporated. All rights reserved. Scanning USB buses for supported XDS110 devices... Setting serial number to "L3144444"...
And now the box asks me to select whether I want to use TIXDS110_Connection-S/N:L31444444. I said yes, and it said to update t=
he
firmware from 2.2.5.1 to 3.0.0.15 (and there was an update button). Thi=
s
works ok, and now since I am not connected to the RTIHU, it is correctl=
y
claiming that it can't connect to the target.
I'll update the serial and firmware on the second one I send you as wel=
l.
73,
Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*
pacsat-dev mailing list -- [email protected] View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected] To unsubscribe send an email to [email protected] Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org
pacsat-dev mailing list -- [email protected] View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected] To unsubscribe send an email to [email protected] Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org
pacsat-dev mailing list -- [email protected] View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected] To unsubscribe send an email to [email protected] Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org
pacsat-dev mailing list -- [email protected] View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected] To unsubscribe send an email to [email protected] Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org
--00000000000059bbda060e872bbb Content-Type: text/html; charset="UTF-8" Content-Transfer-Encoding: quoted-printable
<meta http-equiv=3D"Content-Type" content=3D"text/html; charset=3Dutf-8"><d= iv dir=3D"ltr"><div class=3D"gmail_default" style=3D"font-family:arial,sans= -serif">Thanks Bob. I now have the parts, but have had nothing but tr= ouble both removing and replacing those dumb little connectors! Any h= ints? Are you using hot air or a small iron?</div><div class=3D"gmail= _default" style=3D"font-family:arial,sans-serif"><br clear=3D"all"></div><d= iv><div dir=3D"ltr" class=3D"gmail_signature" data-smartmail=3D"gmail_signa= ture"><div dir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"ltr"><div><di= v dir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"ltr"><font face=3D"ari= al, sans-serif">73,</font><div><font face=3D"arial, sans-serif"><br></font>= </div><div><font face=3D"arial, sans-serif">Burns Fisher, WB1FJ</font></div= > <div><i><span style=3D"font-family:arial,helvetica,sans-serif">AMSAT</span= > <font face=3D"garamond, serif">(R) </font><font face=3D"arial, sans-serif"= > Engineering -- Flight Software</font></i></div></div></div></div></div></d= iv></div></div></div></div></div></div></div></div><br></div><br><div class= =3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Tue, Jan 9, 2024 = at 1:04=E2=80=AFPM Bob Stricklin via pacsat-dev <<a href=3D"mailto:pacsa= [email protected]">[email protected]</a>> wrote:<br></div><blockquote c= lass=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px soli= d rgb(204,204,204);padding-left:1ex">
<div style=3D"overflow-wrap: break-word;"> I received the two Devpack programming boards from Burns. Replaced connecto= rs on both boards and I have tested them on the Quad board and they both wo= rked fine. <div><br> </div> <div>Returning one of these to Burns today.</div> <div><br> </div> <div>Bob</div> <div><br> <div><br> <blockquote type=3D"cite"> <div>On Jan 5, 2024, at 11:21 AM, Burns Fisher (AMSAT) via pacsat-dev <<= a href=3D"mailto:[email protected]" target=3D"_blank">[email protected]= rg</a>> wrote:</div> <br> <div> <div dir=3D"ltr"> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif">I inclu= ded a little extra. The connectors that I had ordered just arrived (h= ot off the plane from Singapore) and I realized that Newark Electroncis had= apparently switched the part number around on me, and they were surface mount! Not useful for me in this case, = but if they are useful for anything you build, I sent you a few.<br clear= =3D"all"> </div> <div> <div dir=3D"ltr" class=3D"gmail_signature"> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"><font face=3D"arial, sans-serif">73,</font> <div><font face=3D"arial, sans-serif"><br> </font></div> <div><font face=3D"arial, sans-serif">Burns Fisher, WB1FJ</font></div> <div><i><span style=3D"font-family:arial,helvetica,sans-serif">AMSAT</span>= <font face=3D"garamond, serif">(R) </font><font face=3D"arial, sans-serif">Engineering -- Flight Software</fon= t></i></div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> <br> </div> <br> <div class=3D"gmail_quote"> <div dir=3D"ltr" class=3D"gmail_attr">On Fri, Jan 5, 2024 at 11:28=E2=80=AF= AM Bob Stricklin via pacsat-dev <<a href=3D"mailto:[email protected]"= target=3D"_blank">[email protected]</a>> wrote:<br> </div> <blockquote class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-= left:1px solid rgb(204,204,204);padding-left:1ex"> <div dir=3D"auto"> <div dir=3D"ltr"></div> <div dir=3D"ltr">Thank you sir. </div> <div dir=3D"ltr"><br> </div> <div dir=3D"ltr">Bob</div> <div dir=3D"ltr"><br> <blockquote type=3D"cite">On Jan 5, 2024, at 10:09=E2=80=AFAM, Burns Fisher= (AMSAT) via pacsat-dev <<a href=3D"mailto:[email protected]" target= =3D"_blank">[email protected]</a>> wrote:<br> <br> </blockquote> </div> <blockquote type=3D"cite"> <div dir=3D"ltr">=EF=BB=BF <div dir=3D"ltr"> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif">BTW, I'= m putting both in the same box but including all the instructions that came= with it. Note that the instructions assume you are going to be using= this with a thing called a SensorTag so you can ignore them :-)</div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif"><br> </div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif">I don't= care which one you return to be with the connector replace, btw. <br> </div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif"><br> </div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif">Good lu= ck!<br> </div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif"><br cle= ar=3D"all"> </div> <div> <div dir=3D"ltr" class=3D"gmail_signature"> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"><font face=3D"arial, sans-serif">73,</font> <div><font face=3D"arial, sans-serif"><br> </font></div> <div><font face=3D"arial, sans-serif">Burns Fisher, WB1FJ</font></div> <div><i><span style=3D"font-family:arial,helvetica,sans-serif">AMSAT</span>= <font face=3D"garamond, serif">(R) </font><font face=3D"arial, sans-serif">Engineering -- Flight Software</fon= t></i></div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> <br> </div> <br> <div class=3D"gmail_quote"> <div dir=3D"ltr" class=3D"gmail_attr">On Fri, Jan 5, 2024 at 10:59=E2=80=AF= AM Burns Fisher (AMSAT) <<a href=3D"mailto:[email protected]" target=3D"_b= lank">[email protected]</a>> wrote:<br> </div> <blockquote class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-= left:1px solid rgb(204,204,204);padding-left:1ex"> <div dir=3D"ltr"> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif">Bob, et= al:</div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif"><br> </div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif">FWIW, t= he official name of the little boards I'm send is TI Simplelink SensorTag D= evpack.</div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif"><br> </div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif">I'm inc= luding a photo of the one that works. You can see when you look at a = new one) that the replacement connector goes on the opposite side of the bo= ard from the existing 10-pin connector. The existing one is female with no key. The new one is male with shr= oud and key. The key is on the outside edge of the board, and the con= nector is on the opposite side of the board from the chip (on the same side= as the larger connector.</div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif"><br> </div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif">I tried= to load code using it (despite not being connect to the RTIHU) and got the= attached error message. I used the xdsdfu utility that the error tal= ks about and discovered this:</div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif"><br> </div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif"><span s= tyle=3D"font-family:monospace">./ti/ccs1020/ccs/ccs_base/common/uscif/xds11= 0/xdsdfu -e<br> <br> USB Device Firmware Upgrade Utility<br> Copyright (c) 2008-2019 Texas Instruments Incorporated. All rights re= served.<br> <br> Scanning USB buses for supported XDS110 devices...<br> <<<< Device 0 >>>><br> VID: 0x0451 PID: 0xbef3<br> Device Name: XDS110 with CMSIS-DAP<br> Version: 2.2.5.1<br> Manufacturer: Texas Instruments<br> Serial Num: L787<br> Mode: Runtime<br> Configuration: Standard<br> Found 1 device.</span><br> </div> <div class=3D"gmail_default" style=3D"font-family:arial,sans-serif"><br cle= ar=3D"all"> </div> <div> <div dir=3D"ltr" class=3D"gmail_signature"> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"> <div> <div dir=3D"ltr"><font face=3D"arial, sans-serif"><span class=3D"gmail_defa= ult" style=3D"font-family:arial,sans-serif">Notice the serial number L787.&= nbsp; One of my working ones has the serial number </span></font>L3122222<span class=3D"gmail_default" style=3D"font-family:ar= ial,sans-serif">. So letter L and 7 digits. I am setting yours = to L31444444 and L31555555. Like this:</span></div> <div dir=3D"ltr"><br> </div> <div dir=3D"ltr"><br> </div> <div dir=3D"ltr"><span style=3D"font-family:monospace">bfisher@skylab:~$ ./= ti/ccs1020/ccs/ccs_base/common/uscif/xds110/xdsdfu -m<br> USB Device Firmware Upgrade Utility<br> Copyright (c) 2008-2019 Texas Instruments Incorporated. All rights re= served.<br> Scanning USB buses for supported XDS110 devices...<br> <<<< Device 0 >>>><br> VID: 0x0451 PID: 0xbef3<br> Device Name: XDS110 with CMSIS-DAP<br> Version: 2.2.5.1<br> Manufacturer: Texas Instruments<br> Serial Num: L787<br> Mode: Runtime<br> Configuration: Standard<br> Switching device into DFU mode.</span></div> <div dir=3D"ltr"><span style=3D"font-family:monospace"><br> </span></div> <div dir=3D"ltr"><span style=3D"font-family:monospace">bfisher@skylab:~$ ./= ti/ccs1020/ccs/ccs_base/common/uscif/xds110/xdsdfu -s L3144444 -r<br> USB Device Firmware Upgrade Utility<br> Copyright (c) 2008-2019 Texas Instruments Incorporated. All rights re= served.<br> Scanning USB buses for supported XDS110 devices...<br> Setting serial number to "L3144444"...</span><br> </div> <div dir=3D"ltr"><span class=3D"gmail_default" style=3D"font-family:arial,s= ans-serif"><br> </span></div> <div style=3D"font-family:arial,sans-serif" class=3D"gmail_default">And now= the box asks me to select whether I want to use TIXDS110_Connection-S/N:L3= 1444444. I said yes, and it said to update the firmware from 2.2.5.1 = to 3.0.0.15 (and there was an update button). This works ok, and now since I am not connected to the RTIHU, it is correc= tly claiming that it can't connect to the target.<br> </div> <div style=3D"font-family:arial,sans-serif" class=3D"gmail_default"><br> </div> <div style=3D"font-family:arial,sans-serif" class=3D"gmail_default">I'll up= date the serial and firmware on the second one I send you as well.<br> </div> <br> <div dir=3D"ltr"><font face=3D"arial, sans-serif"><br> </font></div> <div dir=3D"ltr"><font face=3D"arial, sans-serif">73,</font> <div><font face=3D"arial, sans-serif"><br> </font></div> <div><font face=3D"arial, sans-serif">Burns Fisher, WB1FJ</font></div> <div><i><span style=3D"font-family:arial,helvetica,sans-serif">AMSAT</span>= <font face=3D"garamond, serif">(R) </font><font face=3D"arial, sans-serif">Engineering -- Flight Software</fon= t></i></div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </div> </blockquote> </div> <span></span><br> <span>-----------------------------------------------------------</span><br= > <span></span><br> <span>pacsat-dev mailing list -- <a href=3D"mailto:[email protected]" ta= rget=3D"_blank"> [email protected]</a></span><br> <span>View archives of this mailing list at <a href=3D"https://mailman.amsa= t.org/hyperkitty/list/[email protected]" target=3D"_blank"> https://mailman.amsat.org/hyperkitty/list/[email protected]</a></span><b= r> <span>To unsubscribe send an email to <a href=3D"mailto:pacsat-dev-leave@am= sat.org" target=3D"_blank"> [email protected]</a></span><br> <span>Manage all of your AMSAT-NA mailing list preferences at <a href=3D"ht= tps://mailman.amsat.org/" target=3D"_blank"> https://mailman.amsat.org</a></span><br> </div> </blockquote> </div> <br> -----------------------------------------------------------<br> <br> pacsat-dev mailing list -- <a href=3D"mailto:[email protected]" target= =3D"_blank"> [email protected]</a><br> View archives of this mailing list at <a href=3D"https://mailman.amsat.org/= hyperkitty/list/[email protected]" rel=3D"noreferrer" target=3D"_blank"> https://mailman.amsat.org/hyperkitty/list/[email protected]</a><br> To unsubscribe send an email to <a href=3D"mailto:[email protected]= g" target=3D"_blank"> [email protected]</a><br> Manage all of your AMSAT-NA mailing list preferences at <a href=3D"https://= mailman.amsat.org/" rel=3D"noreferrer" target=3D"_blank"> https://mailman.amsat.org</a><br> </blockquote> </div> <br> -----------------------------------------------------------<br> <br> pacsat-dev mailing list -- <a href=3D"mailto:[email protected]" target= =3D"_blank">[email protected]</a><br> View archives of this mailing list at <a href=3D"https://mailman.amsat.org/= hyperkitty/list/[email protected]" target=3D"_blank"> https://mailman.amsat.org/hyperkitty/list/[email protected]</a><br> To unsubscribe send an email to <a href=3D"mailto:[email protected]= g" target=3D"_blank"> [email protected]</a><br> Manage all of your AMSAT-NA mailing list preferences at <a href=3D"https://= mailman.amsat.org" target=3D"_blank"> https://mailman.amsat.org</a><br> </div> </blockquote> </div> <br> </div> </div>
<br> -----------------------------------------------------------<br> <br> pacsat-dev mailing list -- <a href=3D"mailto:[email protected]" target= =3D"_blank">[email protected]</a><br> View archives of this mailing list at <a href=3D"https://mailman.amsat.org/= hyperkitty/list/[email protected]" rel=3D"noreferrer" target=3D"_blank">= https://mailman.amsat.org/hyperkitty/list/[email protected]</a><br> To unsubscribe send an email to <a href=3D"mailto:[email protected]= g" target=3D"_blank">[email protected]</a><br> Manage all of your AMSAT-NA mailing list preferences at <a href=3D"https://= mailman.amsat.org" rel=3D"noreferrer" target=3D"_blank">https://mailman.ams= at.org</a><br> </blockquote></div>
--00000000000059bbda060e872bbb--
--===============0108675984297293611== Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Content-Disposition: inline
pacsat-dev mailing list -- [email protected] View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected] To unsubscribe send an email to [email protected] Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org
--===============0108675984297293611==--