Also, out issue tracker for the software is here:
https://github.com/AMSAT-NA/PacSatSW/issues

I just added this one, but if you see other problems then feel free to add them or as me to add.  Future ideas should be logged as enhancements.  We can group all of these into 'projects' if we want or as 'milestones' so it is very flexible and allows a large number of issues to be filtered to just the right ones for an objective.

Note that some of the issues are actually closed and I need to do a pass through to clean them up.

One other 'rule' that Burns and I have used in the past is that the person who raises the issue is the person who closes it, once they are happy.

73
Chris 


On Sat, Feb 17, 2024, 09:28 Chris Thompson via pacsat-dev <pacsat-dev@amsat.org> wrote:
Hi all,

The power setting commands were never ported over from Golf.  As Bob said it is currently hard coded to a minimum level for testing in the shack.

We will want this to be commandable in the future, at least to a couple of levels as Burns said.

73
Chris

On Sat, Feb 17, 2024, 09:18 Burns Fisher (AMSAT) via pacsat-dev <pacsat-dev@amsat.org> wrote:
A couple thoughts (and these are based on memory, not looking at code since I am not in my shack)

First, Jim, remember that any changes that I made are all on the git branch that starts WB1FJ... And that branch will not work on the launchpad.  This branch came off "MAIN" so anything in any other branches is not included in WB1FJ...

Second, I did not explicitly mess with anything relating to power in my last round of changes, although most of the calls into the AX5043 code I had to change to include an argument to say which chip to use.  For something transmit-only, though I'm not sure.

And finally, the way power works on Golf (and I probably did not change this when I originally ported it to Launchpad, although someone else may have):  There is a high power and a low power.  The values for high and low are either constants or in MRAM.  But the commands are essentially to set it to high or low power.  On Golf, there is a high/low pair for both normal mode and safe mode, but there are no such modes on Pacsat of course.  Since that must have been ripped out at some point--probably that original port, or by Chris later--I'm not sure just how the power works at this point.

Sorry, I'd look at more of this, but I have a busy weekend prepping for and teaching a ham radio class.

73,

Burns Fisher, WB1FJ
AMSAT(R) Engineering -- Flight Software


On Sat, Feb 17, 2024 at 12:20 AM Jim McCullers via pacsat-dev <pacsat-dev@amsat.org> wrote:
I did some housekeeping last weekend on the files and it appears I went one step to far and don't have the latest version of the software.
I'll pull it down tomorrow.  The version I have sets the 0x0020 which is very low.
Max power is 0x0fff.

Remember the range is not linear.

Congrats

Jim


One more point…
Max power 16 dB would with 5V and we are using 3.3v on the AX5043.

> On Feb 16, 2024, at 9:25 PM, Bob Stricklin via pacsat-dev <pacsat-dev@amsat.org> wrote:
>
> I did test a board today and found it was transmitting every 30 seconds with a power level of about -28 dBm.
>
> I spent some time looking at the code and found where the power level is set to ox0d in a config file and get AX reports this value.
>
> I see in the data sheet for AX5043 where power should range from -10 dB to 16 dB and uses a 12 bit value to set the level. Possibly we are just adjusting upper 8 bits.
>
> We will also be losing power in the differential to single ended converter and shaping circuit. I will probe on this a little more tomorrow but likely just leave it alone and move on for now to be sure and ship boards Monday.
>
> I also see the 30 second interval in the code and some other comments about setting power but does not seem like this is being used.
>
> I could not get a continuous tone and I did not spend time setting up a tight loop to transmit.
>
> I did change the call sign in the configuration to mine.
>
> Bob
>
> -----------------------------------------------------------
>
> pacsat-dev mailing list -- pacsat-dev@amsat.org View archives of this
> mailing list at
> https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org
> To unsubscribe send an email to pacsat-dev-leave@amsat.org Manage all
> of your AMSAT-NA mailing list preferences at https://mailman.amsat.org

-----------------------------------------------------------

pacsat-dev mailing list -- pacsat-dev@amsat.org View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org
To unsubscribe send an email to pacsat-dev-leave@amsat.org Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org


-----------------------------------------------------------

pacsat-dev mailing list -- pacsat-dev@amsat.org
View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org
To unsubscribe send an email to pacsat-dev-leave@amsat.org
Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org

-----------------------------------------------------------

pacsat-dev mailing list -- pacsat-dev@amsat.org
View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org
To unsubscribe send an email to pacsat-dev-leave@amsat.org
Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org

-----------------------------------------------------------

pacsat-dev mailing list -- pacsat-dev@amsat.org
View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org
To unsubscribe send an email to pacsat-dev-leave@amsat.org
Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org