Hi Bob, W7LRD
I am very happy that your problem has been almost solved !
73" de
i8CVS Domenico ----- Original Message ----- From: Bob- W7LRD To: i8cvs Sent: Friday, September 24, 2010 8:31 AM Subject: Re: [amsat-bb] Fw: KR500 bearings
Hello Domenico
Almost done. I am having a problem, when I bolt everything together. When the rotation gets to the end or stop position. If I do not stop it in time it will remain jammed at the stop. It can loosen if I hit the case or loosen the bolts holding the two halves together. I am thinking the stop bolt could be a bit longer, but it worked before and very little has been changed, except for cleaning and lubrication. Thanks for your help.
73 Bob W7LRD
----- Original Message ----- From: "i8cvs" [email protected] To: "AMSAT-BB" [email protected] Sent: Thursday, September 23, 2010 7:43:20 AM Subject: [amsat-bb] Fw: KR500 bearings
Hi Bob W7LRD
My previous message to you via [email protected] was rejected to me !
73" de
i8CVS Domenico
----- Original Message ----- From: i8cvs To: Bob- W7LRD Sent: Thursday, September 23, 2010 4:36 PM Subject: Re: [amsat-bb] KR500 bearings
----- Original Message ----- From: Bob- W7LRD To: i8cvs Sent: Thursday, September 23, 2010 1:13 AM Subject: Re: [amsat-bb] KR500 bearings
Hi Domenico-I am putting everything back together. A couple of questions. Do you find some grease may ooze out when it gets warm?
Hi Bob W7LRD
You should apply any type of black grease normally used over the outside gears of crains machine wich widstand high temperature without to melt.
As the retainer ring which has a little lip seems to hold the grease inside.
It is correct but if you use 2 or 3 more balls then the retainer is non anymore necessary.
Also I loosened the little gear wheel that drives the pot, in order to work the gear train.
You must buy a new one gear wheel !
It is a little trickey to get to, is that pot only 180 degrees or can it go further?
No........... the original pot can rotate for more than 360 degrees
I will have to tighten the gear back to the pot shaft when I can get the pot in the right location. I don't want to accidently run to rotor and keep going at the end of the pot.
The original 500 ohm pot can rotate all around for more than 360 degrees and the center pot wiper of the new model of rotators has a flexible wire outside the case of the pot to provide a safe contact inside of it !
73 Bob W7LRD
Best 73" de
i8CVS Domenico
----- Original Message ----- From: "i8cvs" [email protected] To: "Bob- W7LRD" [email protected], "AMSAT-BB" [email protected] Sent: Tuesday, September 21, 2010 8:26:11 AM Subject: Re: [amsat-bb] KR500 bearings
----- Original Message ----- From: "Bob- W7LRD" [email protected] To: [email protected] Sent: Tuesday, September 21, 2010 1:54 AM Subject: [amsat-bb] KR500 bearings > > > Hi-I am looking for a supplier of bearings and the support for them for the KR500 el rotor. I called Vertex and they're not sure if the bearings are the same as the current 5400/5500 series. The Kenpro product line is no longer in production. > > 73 Bob W7LRD > > Seattle
Hi Bob, W7LRD
The diameter of each ball for the bearing of a KR500 is 0.312" or 5 / 16 inch or 7.9375 mm. I suggest you to remove both stainless steel bearing holders throw it away and add 2 or 3 more balls in each bearing in order to replace the room of the holders teeth. I did it but I do not remember exactly if I added 2 or 3 more balls. Fill the bearing wrinkles of the rotor housing with black dense molibdene grease and pull the balls in it.It works very well for me from many years now.
73" de
i8CVS Domenico
_______________________________________________ Sent via [email protected]. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb