[AMSAT-BB] Re: SatPC32 problem- Access is denied

29 Dec 2021

      Hi Erich, I'm using just the USB port on both the 9100 and the 9700.
73 and HNY
Jeff kb2m
On 12/29/2021 2:19 AM, Erich Eichmann wrote:
...
Hi Jeff,
How does the CAT control of the IC-9700 work on your two stations, via 
the CI-V port of the IC-9700 and an ICOM CAT cable or via the USB port 
of the iC-9700?
73s and Happy New Year
Erich, DK1TB
Am 28.12.2021 um 23:10 schrieb jeff griffin:
...
I have a similar problem with my 9700. I have a 9100 along with the 
9700. The problem is only with the 9700. It also only happens here at 
my Florida home. The 9700 works flawlessly at my QTH in NJ It also 
works 100% when I use my 9700 for FD, and portable operations from 
the tailgate of my vehicle. The only time I experience SatPC32 drop 
out issues with my 9700 is just here at my winter home.
What happens is I notice I'm not doppler correcting, so I have to 
close SatPC32 and power cycle the 9700. This happens about 50% of the 
time and only while operating on linear sats.  It's been an issue for 
about a year, I've owned the 9700 for about 2 years.It worked fine 
here for about a year. I even  reloaded the PC's operating system 
when I upgraded to solid state drives. Problem remains. I  swapped 
USB cables between the 9700 and 9100 and the problem follows the 
9700. I do use a different rotor system here, and AlfaSpid controlled 
by a Green Heron RT-21, and PstRotator. Up north I'm using a Yaesu 
5500 with a LVG box.  I'm convinced it's something to do with the 
9700 itself. This is sorta driving me crazy as I can't figure out 
what the problem is. I'm very interested in trying any suggestions 
from this thread...
73 Jeff kb2m
On 12/28/2021 3:31 PM, Jim, ND9M / VQ9JC via AMSAT-BB wrote:
...
You're right: running the program under my Admin profile is not the 
same as "Run as Admin", and I'd forgotten to try that. Intermittent 
problems can be annoyingly slow to show themselves, but I'll go down 
that rabbit hole and start over.
73,
Jim, ND9M
-----Original Message-----
From: Roger Heindl rwheindl@gmail.com
To: Jim, ND9M / VQ9JC claryco@aol.com
Sent: Tue, Dec 28, 2021 4:54 pm
Subject: Re: [AMSAT-BB] Re: SatPC32 problem- Access is denied
In case it isn't the cable, have you tried running SatPC32 as 
administrator also?
73,
AC9BT
On Tue, Dec 28, 2021 at 12:55 AM Jim, ND9M / VQ9JC via AMSAT-BB 
amsat-bb@amsat.org wrote:
I feel your pain, Larry. I have seen the very same thing happen
on my end a bunch of times; it doesn't happen regularly, but it
happens enough that I have to keep a close watch on SatPC32. I'm
a full time RVer, so all of my operating is portable.When I
operate from what I consider my home grid (EM70), it's generally
not that big of a deal, but it's happened during roving trips too.

If the truck is disconnected from the fifth wheel, I'll set up
on the tail gate; otherwise, I'll use a small folding table from
Wally Worldand set up on that. My IC-9700 is controlled usually
by an Asus netbook but sometimes by an HP laptop; both are
Windows 10. I've used a variety of cables, but for the last
couple months have been using a Tripp Lite cable with ferrite
chokes on both end.

My thinking was that the problem is RFI related, so I've taken
to keeping the laptop separated from the rig by as much distance
as possible and in the opposite direction from the current
satellite pass' general azimuth. After I started spacing the rig
and laptop farther apart, I don't see the problem occur as much,
but it still does occasionally.

Most times, I discover SatPC32 has crashed because I hear my
downlink signal "take off" and I start sounding like Donald
Duck. A quick glance at the Tracking menu invariably shows that
the Cat control has become disabled, i.e. "C+" has become "C-".
My eyesight isn't what it used to be, so spotting that change
gets a little tricky since the laptop is farther away from the
rig. I get the "Access Denied" message when clicking the "X"
too. Closing the program with Alt F -> Q and then restarting it
usually does the trick, but sometimes I have to do a full laptop
reboot as well as disconnect and reconnect the USB cable. One
laptop has two USB ports and the other has three, and I've seen
the same thing happen on all ports. (Thankfully, the port
assignment doesn't change when I move the USB cable around, but
I keep a watch on that too just in case.)

So far, I've noticed these symptoms happen only on U/V birds,
not V/U. Also, I've seen this happen regardless of when I'm
using my User account or Admin account.

I'm interested to see what you find out. I'll let you know if I
figure something out.

73,

Jim, ND9M

-----Original Message-----
From: Larry Ryan <llryan807@gmail.com>
To: amsat-bb@amsat.org
Sent: Mon, Dec 27, 2021 7:28 pm
Subject: [AMSAT-BB] SatPC32 problem- Access is denied

This problem has occurred a few times during a pass. SatPC32
stops working (I can see its not updating the frequencies) and
whenever I click the tone control (T0, T1) I get the message
"Access is denied" and the Countdown window dissappears. If I
click OK on the message popup, the window reappears.  It gets
worse;
In order to restore operation meaning to get doppler control so
I can make a sat QSO, I need to restart SatPC32 but when I click
the X, I get the error message. I must click File, Quit.
By this time, the pass is over.  Restarting SatPC32 does restore
normal operation.
This problem is intermittent. Most of the time, SatPC32 works
well with my IC-9700. The PC is running Win10.
Do these symptoms point to a known issue or do I just reinstall
everything?

-----------------------------------------------------------

Sent via AMSAT-BB(a)amsat.org <http://amsat.org/>. AMSAT-NA
makes this open forum available
to all interested persons worldwide without requiring
membership. Opinions expressed
are solely those of the author, and do not reflect the official
views of AMSAT-NA.
Acceptable Use and Privacy Policies available at
https://www.amsat.org/about-amsat/

View archives of this mailing list at
https://mailman.amsat.org/hyperkitty/list/amsat-bb@amsat.org
To unsubscribe send an email to amsat-bb-leave(a)amsat.org
<http://amsat.org/>
Manage all of your AMSAT-NA mailing list preferences at
https://mailman.amsat.org

-----------------------------------------------------------

Sent via AMSAT-BB(a)amsat.org <http://amsat.org/>. AMSAT-NA
makes this open forum available
to all interested persons worldwide without requiring
membership. Opinions expressed
are solely those of the author, and do not reflect the official
views of AMSAT-NA.
Acceptable Use and Privacy Policies available at
https://www.amsat.org/about-amsat/

View archives of this mailing list at
https://mailman.amsat.org/hyperkitty/list/amsat-bb@amsat.org
To unsubscribe send an email to amsat-bb-leave(a)amsat.org
<http://amsat.org/>
Manage all of your AMSAT-NA mailing list preferences at
https://mailman.amsat.org

Sent via AMSAT-BB(a)amsat.org. AMSAT-NA makes this open forum available
to all interested persons worldwide without requiring membership. Opinions expressed
are solely those of the author, and do not reflect the official views of AMSAT-NA.
Acceptable Use and Privacy Policies available athttps://www.amsat.org/about-amsat/
View archives of this mailing list at
https://mailman.amsat.org/hyperkitty/list/amsat-bb@amsat.org
To unsubscribe send an email to amsat-bb-leave(a)amsat.org
Manage all of your AMSAT-NA mailing list preferences athttps://mailman.amsat.org