I'm trying to set up an IC910 with SatPC32 to work with a VHF up / UHF down satellite.
I've built a doppler.sqf entry with 435xxx as the downlink and 145xxx as the uplink. The 910 will only transmit on the main band so that needs to be the VHF uplink. But SatPC32 puts the RX freq there, and the TX freq in the sub band.
Also, what should be checked in the options in the radio setup window. I have none checked at this time.
Is there a setting to change the main/sub tx/rx or can I just swap the up and down freqs in the doppler.sqf entry?
Jim
Check option "Satellite Mode", leave other options unchecked.
73s, Erich, DK1TB
Am 29.04.2017 um 04:25 schrieb Jim White:
I'm trying to set up an IC910 with SatPC32 to work with a VHF up / UHF down satellite.
I've built a doppler.sqf entry with 435xxx as the downlink and 145xxx as the uplink. The 910 will only transmit on the main band so that needs to be the VHF uplink. But SatPC32 puts the RX freq there, and the TX freq in the sub band.
Also, what should be checked in the options in the radio setup window. I have none checked at this time.
Is there a setting to change the main/sub tx/rx or can I just swap the up and down freqs in the doppler.sqf entry?
Jim
Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
Jim,
In satellite mode, the IC910H puts the sub-band downlink on the top of the display and the main-band on the bottom. This is reversed from the normal display. Is this what you are referring to?
bob ko6tz
I'm trying to set up an IC910 with SatPC32 to work with a VHF up / UHF down satellite.
I've built a doppler.sqf entry with 435xxx as the downlink and 145xxx as the uplink. The 910 will only transmit on the main band so that needs to be the VHF uplink. But SatPC32 puts the RX freq there, and the TX freq in the sub band.
Also, what should be checked in the options in the radio setup window. I have none checked at this time.
Is there a setting to change the main/sub tx/rx or can I just swap the up and down freqs in the doppler.sqf entry?
Jim
Thanks to all who replied. We have it figured out.
Jim
On 4/29/2017 6:29 AM, KO6TZ Bob wrote:
Jim,
In satellite mode, the IC910H puts the sub-band downlink on the top of the display and the main-band on the bottom. This is reversed from the normal display. Is this what you are referring to?
bob ko6tz
I'm trying to set up an IC910 with SatPC32 to work with a VHF up / UHF down satellite.
I've built a doppler.sqf entry with 435xxx as the downlink and 145xxx as the uplink. The 910 will only transmit on the main band so that needs to be the VHF uplink. But SatPC32 puts the RX freq there, and the TX freq in the sub band.
Also, what should be checked in the options in the radio setup window. I have none checked at this time.
Is there a setting to change the main/sub tx/rx or can I just swap the up and down freqs in the doppler.sqf entry?
Jim
Sent via AMSAT-BB@amsat.org. AMSAT-NA makes this open forum available to all interested persons worldwide without requiring membership. Opinions expressed are solely those of the author, and do not reflect the official views of AMSAT-NA. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
participants (3)
-
Erich Eichmann -
Jim White -
KO6TZ Bob