- pacsat-dev - mailman.amsat.org

Flight software info is up now on PacSat gitHub documentation (references) folder
by Burns Fisher (AMSAT) 03 Feb '24

03 Feb '24

One was there already and I forgot! But the three of interest are: Multiple_CPUs (which really talks about the ccxml files in CCS) Use_of_HalCoGen and Software_Descirption 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*

1 0

Re: Hooray! Some serial output!
by Burns Fisher (AMSAT) 03 Feb '24

03 Feb '24

Probably the last note today unless something happens in the next hour. The console now seems fine. I've gotten to the point where I can type in commands and thus easily execute tests. I actually commented out starting the other tasks so I could pay attention to one thing at a time. I also commented out initializing the RTC--that was hanging for some reason. I'm getting a lot of errors, as the system starts up largely because (I think) the MRAM values are not what it expects. So I thought I would start on the MRAM. There is a simple command call "get mram sr" which reads the status registers of all 4 MRAMs and prints it out. That seemed like an easy place to start. However, all of them are returning 0xFF. Remember that an SPI master does not really have any way to tell if the slave is responding. The data lines are high by default, so 0xFF is typically what you get when the slave does not respond. I've done a lot of checking and found some stuff in HalCoGen that I did not have right, but still no good response even after I fixed those places (I'm comparing them with the HalCoGen on both the LaunchPad version and the RTIHU version). Just like with the serial line, I am getting appropriate interrupts. However, this time there are no wires that I might have gotten backwards. I'm going to have to check continuity on the traces from the MRAMs to the processor, at least as closely as I can. It turns out (intentionally??) that MRAM #4, which is U79 is not installed on my board. But that is helpful because that means that I can access all the SPI bus lines and at least the MRAM4 chip select line (but not the others). So I'll look at that later. Also voltages etc. SOMETHING is getting read from the AX5043s (or at least 2 of them) that is not 0xff, so they may be working. I have not poked around with I2c yet but it should be easy to set up a way to read the MAX31725s. 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software* On Fri, Feb 2, 2024 at 11:53 AM Chris Thompson via pacsat-dev < pacsat-dev(a)amsat.org> wrote: > Wow, very good. Well done. And well done Bob on the hardware. Great to > see it working. > > 73 > Chris > > On Fri, Feb 2, 2024, 10:33 Burns Fisher (AMSAT) via pacsat-dev < > pacsat-dev(a)amsat.org> wrote: > >> Ok, last one for the moment. The console is now working fine with >> interrupts at 38400 baud. >> 73, >> >> Burns Fisher, WB1FJ >> *AMSAT(R) Engineering -- Flight Software* >> >> >> On Fri, Feb 2, 2024 at 10:25 AM Burns Fisher (AMSAT) <wb1fj(a)fisher.cc> >> wrote: >> >>> To avoid suspense: The schematic perfectly matches what HALCOGEN claims >>> are the correct Rx and Tx pins. If I remove the connection to pin 92 (Rx) >>> it keeps going. So the blinky board is certainly correct. >>> >>> Of course Rx and Tx are relative to which end of the wire you are >>> looking at. That is Tx on the board connects to Rx on the terminal. That >>> seems like the most likely explanation. The usb/serial adapter is labelled >>> from the POV of the terminal. >>> >>> Anyway...speed test next. >>> >>> 73, >>> >>> Burns Fisher, WB1FJ >>> *AMSAT(R) Engineering -- Flight Software* >>> >>> >>> On Fri, Feb 2, 2024 at 10:14 AM Burns Fisher (AMSAT) <wb1fj(a)fisher.cc> >>> wrote: >>> >>>> I put in this code temporarily: >>>> >>>> >>>> GPIOEzInit(LED1); >>>> GPIOEzInit(LED2); >>>> GPIOEzInit(LED3); >>>> GPIOSetOn(LED1); >>>> GPIOSetOff(LED2); >>>> sciSetBaudrate(scilinREG, 110); >>>> sciSetBaudrate(sciREG, 110); >>>> while(1){ >>>> GPIOToggle(LED1); >>>> sciSend(sciREG,38,"Starting a test on the SCI register\r\n"); >>>> GPIOToggle(LED2); >>>> sciSend(scilinREG,38,"Starting a test on the LIN register\r\n"); >>>> } >>>> >>>> The GPIO routines are my normal driver routines. The sciSet and >>>> sciSend are the HALCoGen routines not using any interrupts or anything >>>> else. Note that I set the baudrate to 110 (R-e-a-l slow!) and sent 38 >>>> characters. That it, it should take about 3.8 seconds to print. And >>>> indeed the light pattern changes at a rate of approximately every 4 >>>> seconds. >>>> >>>> I have a terminal connected to PC104 pins 88 and 92 and set for 110 >>>> baud connected and at first saw nothing. Then I reversed the rx and tx >>>> pins and..... >>>> >>>> Starting a test on the SCI register >>>> Starting a test on the SCI register >>>> Starting a test on the SCI register >>>> Starting a test on the SCI register >>>> Starting a test on the SCI register >>>> Starting a test on the SCI register >>>> Starting a test on the SCI register >>>> Starting a test on the SCI register >>>> Starting a test on the SCI register >>>> >>>> SO! Either I have the colors wrong on my serial-to-USB connector, or >>>> they are backwards on the blinky board. Will figure out which next, and >>>> then try higher speeds. >>>> >>>> >>>> 73, >>>> >>>> Burns Fisher, WB1FJ >>>> *AMSAT(R) Engineering -- Flight Software* >>>> >>> >> ----------------------------------------------------------- >> >> pacsat-dev mailing list -- pacsat-dev(a)amsat.org >> View archives of this mailing list at >> https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org >> To unsubscribe send an email to pacsat-dev-leave(a)amsat.org >> Manage all of your AMSAT-NA mailing list preferences at >> https://mailman.amsat.org >> > > ----------------------------------------------------------- > > pacsat-dev mailing list -- pacsat-dev(a)amsat.org > View archives of this mailing list at > https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org > To unsubscribe send an email to pacsat-dev-leave(a)amsat.org > Manage all of your AMSAT-NA mailing list preferences at > https://mailman.amsat.org >

1 0

Re: Quick update
by Bob Stricklin 03 Feb '24

03 Feb '24

Burns, I just got back home for a day long visit to Dallas and UTD to take care of my other volunteer projects. Sounds like all good news. I am very happy to see this! Comments back from below: 1. Good on the temp sensor reading. The temp sensor you are reading is the one down next to the AX5043 transmitter chip. There is a second temp sensor at 0x91. The code will need to be changed to support this one eventually. The second temp sensor is next to the CPU chip up between memory and the CPU. You should be able to read this one also by just changing the address in the code from 0x90 to 0x91. Chris can add the second one later. We can move the I2C address to another address within the range of addresses provided on a later build. We can coordinate adding an external A/D if needed but there are several A/Ds built into the TMS570. Three of these are being used now to monitor supply voltages. The A/Ds are using 3.3V and GND for reference. The 5V A/D is AD1/N_12 and should be at 2.5V for the middle of the range. The actual 5V supply may be running a little low though so don’t be surprised if lower. The 3.3V supply is on AD1N_4. Again this should read mid range on the A/D which will be 3.3 / 2 or 1.65 volts. The 1.2 V supply is on AD1N_13 and should read 1.2 / 3.3 * (2^12). This is something you can work on testing but should work as designed. There is an option later to use two of the A/Ds on a critical measurement and then use the redundant capabilities of this CPU to make sure the readings are accurate. We could also monitor other things with more A/Ds but this should be enough for a prototype. The AX5043 readings we might measure with analog readings are available in registers I believe. 2. The one wire pull-up issue should be addressed by activating the Pull up on N2HET1_14. We could add another pull-up on the board later. I thought the idea was to have a security string on the PCB that could be matched with ground transmissions. Dropping chips if fine though as it will save current. Not much saved here though. 3. The SPI lines for the AX5043 are available on J801. We would have to add the memory SPI if needed. J801 is on one of the schematic pages. We can add the I2C bus to the PC104 if a pin set is defined and the signals are needed there. We will have to coordinate this with others. I could do this with a couple of jumpers if thee is an advantage to it now. We need to be careful with two Masters and adding capacitance to the line. Also voltages between systems. The box I am building will have the PC104 available from the top for accessing the serial port and other things. I was thinking of making a small PCB that just picks up a few of the pins on the end to make the serial port connection easier and from outside the box. Add a couple of indicator LEDs also. Please test the memory and see if any of it is working. This will need some work on the SPI pin selection and probably what you have already figured out. Would like to see if you can read and write anything to each of the 5 AX5043s. When we get through all of the above then all the CPU related things will have been tested. You would need jumper cables just to feed signals on and off the AX5043 for RF test so this should probably come later. Just reading and writing to the devices would be a good milestone. Bob On Feb 2, 2024, at 4:52 PM, Burns Fisher (AMSAT) <wb1fj(a)fisher.cc<mailto:wb1fj@fisher.cc>> wrote: I2c works. Pacsat>get i2c I2c device state: (1 is ok) PacSat Board Temp: 1 RTC: 1 Pacsat>get rtc Date: 2000-1-1 06:18:45 UTC Time: 946707525 vs IHU Unix time 1000000132 Pacsat>get temp Pacsat board temp is 92 ( 26.0 degrees C) Comments for the future: 1) The temp sensors should be at different addresses. We have no ADS7828 I2c A/D converters, but they are very useful and space-proven gadgets for reading voltages, etc. However, the "easy" temp addresses clash with the 7828. It's hard to see becasue Max uses 8 bit values for addresses (with bit 0 set to 0) while the rest of the world uses 7 bit values. So Max's address 0x90 is really 0x48 to everyone else. 2) The one-wire secure memory is totally unused and I never managed to make it work on the RTIHU. I think it needs a pullup (I don't recall why the builtin pullup does not work). But regardless, I suppose we could put an encryption key in it, but it is not especially useful when it is flying in space anyway :-) 3) In the future it would be nice to have SPI and I2c busses available at test points. Or even on the PC104. 73, Burns Fisher, WB1FJ AMSAT(R) Engineering -- Flight Software

1 0

Re: Just a note for the Blinky board AX5043
by Chris Thompson 02 Feb '24

02 Feb '24

Yes, we found that 91nH worked on Jim's board. But the actual value will depend on board layout and any stray inductance. 73 Chris On Fri, Feb 2, 2024, 11:41 Jim McCullers via pacsat-dev < pacsat-dev(a)amsat.org> wrote: > Correct. > > 91nH or something close. It sets the PLL bandwidth. > > > > Congrats by the way. > > > > Jim > > > > This won't stop me for anything I will do, but the receiver will not lock > (VHF) unless the iplace marked "jumper if no inductor" actually has an > inductor. I think short is ok for UHF but VHF needs 91nH. (Do you > remember, Jim?) > > > 73, > > > > Burns Fisher, WB1FJ > > *AMSAT**(R) **Engineering -- Flight Software* > > ----------------------------------------------------------- > > pacsat-dev mailing list -- pacsat-dev(a)amsat.org > View archives of this mailing list at > https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org > To unsubscribe send an email to pacsat-dev-leave(a)amsat.org > Manage all of your AMSAT-NA mailing list preferences at > https://mailman.amsat.org >

1 0

Re: Hooray! Some serial output!
by Chris Thompson 02 Feb '24

02 Feb '24

Wow, very good. Well done. And well done Bob on the hardware. Great to see it working. 73 Chris On Fri, Feb 2, 2024, 10:33 Burns Fisher (AMSAT) via pacsat-dev < pacsat-dev(a)amsat.org> wrote: > Ok, last one for the moment. The console is now working fine with > interrupts at 38400 baud. > 73, > > Burns Fisher, WB1FJ > *AMSAT(R) Engineering -- Flight Software* > > > On Fri, Feb 2, 2024 at 10:25 AM Burns Fisher (AMSAT) <wb1fj(a)fisher.cc> > wrote: > >> To avoid suspense: The schematic perfectly matches what HALCOGEN claims >> are the correct Rx and Tx pins. If I remove the connection to pin 92 (Rx) >> it keeps going. So the blinky board is certainly correct. >> >> Of course Rx and Tx are relative to which end of the wire you are looking >> at. That is Tx on the board connects to Rx on the terminal. That seems >> like the most likely explanation. The usb/serial adapter is labelled from >> the POV of the terminal. >> >> Anyway...speed test next. >> >> 73, >> >> Burns Fisher, WB1FJ >> *AMSAT(R) Engineering -- Flight Software* >> >> >> On Fri, Feb 2, 2024 at 10:14 AM Burns Fisher (AMSAT) <wb1fj(a)fisher.cc> >> wrote: >> >>> I put in this code temporarily: >>> >>> >>> GPIOEzInit(LED1); >>> GPIOEzInit(LED2); >>> GPIOEzInit(LED3); >>> GPIOSetOn(LED1); >>> GPIOSetOff(LED2); >>> sciSetBaudrate(scilinREG, 110); >>> sciSetBaudrate(sciREG, 110); >>> while(1){ >>> GPIOToggle(LED1); >>> sciSend(sciREG,38,"Starting a test on the SCI register\r\n"); >>> GPIOToggle(LED2); >>> sciSend(scilinREG,38,"Starting a test on the LIN register\r\n"); >>> } >>> >>> The GPIO routines are my normal driver routines. The sciSet and sciSend >>> are the HALCoGen routines not using any interrupts or anything else. Note >>> that I set the baudrate to 110 (R-e-a-l slow!) and sent 38 characters. >>> That it, it should take about 3.8 seconds to print. And indeed the light >>> pattern changes at a rate of approximately every 4 seconds. >>> >>> I have a terminal connected to PC104 pins 88 and 92 and set for 110 >>> baud connected and at first saw nothing. Then I reversed the rx and tx >>> pins and..... >>> >>> Starting a test on the SCI register >>> Starting a test on the SCI register >>> Starting a test on the SCI register >>> Starting a test on the SCI register >>> Starting a test on the SCI register >>> Starting a test on the SCI register >>> Starting a test on the SCI register >>> Starting a test on the SCI register >>> Starting a test on the SCI register >>> >>> SO! Either I have the colors wrong on my serial-to-USB connector, or >>> they are backwards on the blinky board. Will figure out which next, and >>> then try higher speeds. >>> >>> >>> 73, >>> >>> Burns Fisher, WB1FJ >>> *AMSAT(R) Engineering -- Flight Software* >>> >> > ----------------------------------------------------------- > > pacsat-dev mailing list -- pacsat-dev(a)amsat.org > View archives of this mailing list at > https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org > To unsubscribe send an email to pacsat-dev-leave(a)amsat.org > Manage all of your AMSAT-NA mailing list preferences at > https://mailman.amsat.org >

1 0

Re: Just a note for the Blinky board AX5043
by Jim McCullers 02 Feb '24

02 Feb '24

Correct. 91nH or something close. It sets the PLL bandwidth. Congrats by the way. Jim This won't stop me for anything I will do, but the receiver will not lock (VHF) unless the iplace marked "jumper if no inductor" actually has an inductor. I think short is ok for UHF but VHF needs 91nH. (Do you remember, Jim?) 73, Burns Fisher, WB1FJ AMSAT(R) Engineering -- Flight Software

1 0

Just a note for the Blinky board AX5043
by Burns Fisher (AMSAT) 02 Feb '24

02 Feb '24

This won't stop me for anything I will do, but the receiver will not lock (VHF) unless the iplace marked "jumper if no inductor" actually has an inductor. I think short is ok for UHF but VHF needs 91nH. (Do you remember, Jim?) 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*

1 0

Hooray! Some serial output!
by Burns Fisher (AMSAT) 02 Feb '24

02 Feb '24

I put in this code temporarily: GPIOEzInit(LED1); GPIOEzInit(LED2); GPIOEzInit(LED3); GPIOSetOn(LED1); GPIOSetOff(LED2); sciSetBaudrate(scilinREG, 110); sciSetBaudrate(sciREG, 110); while(1){ GPIOToggle(LED1); sciSend(sciREG,38,"Starting a test on the SCI register\r\n"); GPIOToggle(LED2); sciSend(scilinREG,38,"Starting a test on the LIN register\r\n"); } The GPIO routines are my normal driver routines. The sciSet and sciSend are the HALCoGen routines not using any interrupts or anything else. Note that I set the baudrate to 110 (R-e-a-l slow!) and sent 38 characters. That it, it should take about 3.8 seconds to print. And indeed the light pattern changes at a rate of approximately every 4 seconds. I have a terminal connected to PC104 pins 88 and 92 and set for 110 baud connected and at first saw nothing. Then I reversed the rx and tx pins and..... Starting a test on the SCI register Starting a test on the SCI register Starting a test on the SCI register Starting a test on the SCI register Starting a test on the SCI register Starting a test on the SCI register Starting a test on the SCI register Starting a test on the SCI register Starting a test on the SCI register SO! Either I have the colors wrong on my serial-to-USB connector, or they are backwards on the blinky board. Will figure out which next, and then try higher speeds. 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*

1 2

Re: Pacsat dev mtg 2/1/2024
by Bob Stricklin 02 Feb '24

02 Feb '24

Here are some photos which show the RX1 TX1 pins used on the PCB. Also the same pins used on the Launchpad board shown on the connect shots below, On the TI drawing it is J2 pins 3 (RX) and 4 (TX). On Jims schematic it is J2 pins 5 (RX) and 7 (TX). So the three pins needed are together on the PC104, Pin 92 (RX), Pin 88 (TX), and GND (Pin 84). You can see from the hilite on the PCB the lines go directly from the CPU to the pins. The maximum voltage on these pins is +4.6V. Be careful with this. Bob [cid:8C8C1E64-6FE2-47D4-8A91-446A1607F934@StricklinRanch.com][cid:26BCFF7D-526B-41B1-BE08-9C14089D931C@StricklinRanch.com][cid:3464A58C-6F09-4BD4-8BA3-21E4C9527AEF@StricklinRanch.com] [cid:DB96025C-1688-4C30-8B09-91396D422643@StricklinRanch.com][cid:EEEC3836-D721-4093-BF4C-5D37C414DADF@StricklinRanch.com] On Feb 1, 2024, at 4:53 PM, Burns Fisher (AMSAT) via pacsat-dev <pacsat-dev(a)amsat.org<mailto:pacsat-dev@amsat.org>> wrote: FYI, I have another meeting at 7 which may not be done in time. I'll come if I can. But for my report: I have the software loading as a git branch from what Chris is using, and it starts up fine, including starting the OS. At some point it resets, but I'm not worried about that yet. Right now I am trying to get anything out of the serial port with no luck even just jamming a character directly into UART transmit buffer. So I'm starting to think this is a hardware issue. Either on the board, or more likely that I have the rx/tx lines reversed, or plugged into the wrong two pins (out of 104!) 73, Burns Fisher, WB1FJ AMSAT(R) Engineering -- Flight Software On Thu, Feb 1, 2024 at 5:13 PM Bill via pacsat-dev <pacsat-dev(a)amsat.org<mailto:pacsat-dev@amsat.org>> wrote: Pacsat dev mtg 2/1/2024 Thu, Feb 1, 2024 7:00 PM - 9:00 PM (CST) Please join my meeting from your computer, tablet or smartphone. https://meet.goto.com/133573605 You can also dial in using your phone. (For supported devices, tap a one-touch number below to join instantly.) United States: +1 (646) 749-3122 - One-touch: tel:+16467493122,,133573605# Access Code: 133-573-605 Join from a video-conferencing room or system. Dial in or type: 67.217.95.2 or inroomlink.goto.com<http://inroomlink.goto.com/> Meeting ID: 133 573 605 Or dial directly: 133573605(a)67.217.95.2<mailto:133573605@67.217.95.2> or 67.217.95.2##133573605 Get the app now and be ready when your first meeting starts: https://meet.goto.com/install ----------------------------------------------------------- pacsat-dev mailing list -- pacsat-dev(a)amsat.org<mailto:pacsat-dev@amsat.org> View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org To unsubscribe send an email to pacsat-dev-leave(a)amsat.org<mailto:pacsat-dev-leave@amsat.org> Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org<https://mailman.amsat.org/> ----------------------------------------------------------- pacsat-dev mailing list -- pacsat-dev(a)amsat.org<mailto:pacsat-dev@amsat.org> View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org To unsubscribe send an email to pacsat-dev-leave(a)amsat.org<mailto:pacsat-dev-leave@amsat.org> Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org

1 0

Re: Pacsat dev mtg 2/1/2024
by Burns Fisher (AMSAT) 01 Feb '24

01 Feb '24

FYI, I have another meeting at 7 which may not be done in time. I'll come if I can. But for my report: I have the software loading as a git branch from what Chris is using, and it starts up fine, including starting the OS. At some point it resets, but I'm not worried about that yet. Right now I am trying to get anything out of the serial port with no luck even just jamming a character directly into UART transmit buffer. So I'm starting to think this is a hardware issue. Either on the board, or more likely that I have the rx/tx lines reversed, or plugged into the wrong two pins (out of 104!) 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software* On Thu, Feb 1, 2024 at 5:13 PM Bill via pacsat-dev <pacsat-dev(a)amsat.org> wrote: > Pacsat dev mtg 2/1/2024 > Thu, Feb 1, 2024 7:00 PM - 9:00 PM (CST) > > Please join my meeting from your computer, tablet or smartphone. > > https://meet.goto.com/133573605 > > You can also dial in using your phone. > (For supported devices, tap a one-touch number below to join instantly.) > > United States: +1 (646) 749-3122 > - One-touch: tel:+16467493122,,133573605# > > Access Code: 133-573-605 > > Join from a video-conferencing room or system. > Dial in or type: 67.217.95.2 or inroomlink.goto.com > Meeting ID: 133 573 605 > Or dial directly: 133573605(a)67.217.95.2 or 67.217.95.2##133573605 > > > Get the app now and be ready when your first meeting starts: > https://meet.goto.com/install > > > > ----------------------------------------------------------- > > pacsat-dev mailing list -- pacsat-dev(a)amsat.org > View archives of this mailing list at > https://mailman.amsat.org/hyperkitty/list/pacsat-dev@amsat.org > To unsubscribe send an email to pacsat-dev-leave(a)amsat.org > Manage all of your AMSAT-NA mailing list preferences at > https://mailman.amsat.org >

1 0