- pacsat-dev - mailman.amsat.org

Re: TMS570 Debug board
by Jim McCullers 08 Dec '23

08 Dec '23

The last thing I ordered from Newark was also shipped from the UK with no shipping communications and as I recall took a long time. It was also an obsolete component by DigiKey and Mouser. Keep us posted. Jim Ok, Bob. The picture sure looks like there are "holes" there, but you never know. I do think that I asked Zach to put the connector on the bottom so it would line the ribbon cable up correctly with the RTIHU connector. We'll find out. BTW, Newark says they are sending the board from the UK. Hmm. 73, Burns Fisher, WB1FJ AMSAT(R) Engineering -- Flight Software On Fri, Dec 8, 2023 at 11:00 AM Bob Stricklin via pacsat-dev <pacsat-dev(a)amsat.org <mailto:[email protected]> > wrote: Burns, I believe he is talking about a 10 pin connector on the bottom left corner of the photo that is turned down below the board. He probably did this to make a standard ribbon cable work with female IDC connectors on each end. We can make that change if the boards are shipped. It may be that Newark inventory is there because they do not got so much business on TI product. Normally when an OEM drops a product they pull all the distributor inventory back. These may be a third party board which is fine if they have the same processor and code. It will be interesting to see if the TI ARM processor TM4C1294NCPDTT3R is on these boards. If it is and several people working on AMSAT projects need these boards we probably should buy more. The info I have is the design information I showed last night that Zach shared with me on an AMSAT version of this programming interface board. Bob On Dec 8, 2023, at 9:41 AM, Burns Fisher (AMSAT) via pacsat-dev <pacsat-dev(a)amsat.org <mailto:[email protected]> > wrote: Thanks, Zach. That might mean that what I ordered is different. See in the picture, the place where you added the connector is not populated. (You have to hover over it to get the expanded version in order to see it). https://www.newark.com/texas-instruments/cc-devpack-debug/debugger-devpak-s… Well see what happens. Actually do you have a couple of male connectors that you could send me? That way, I could easily add it in and test the new board (assuming it comes...maybe you'd better wait until I get a shipping number :-) ) 73, Burns Fisher, WB1FJ AMSAT(R) Engineering -- Flight Software On Fri, Dec 8, 2023 at 10:32 AM Zach Metzinger <zmetzing(a)pobox.com <mailto:[email protected]> > wrote: On 12/8/23 08:07, Burns Fisher (AMSAT) wrote: > Note to Pacsat folks: It appears (and Zach can confirm) that Zach must > have just ADDED a connector into a DNP space on the board...this is > based on the pictures. Hello Burns and the Pacsat team, This is not correct; I replace the female 2x5 connector with a male 2x5 shrouded/keyed connector. Instructions, already sent to Bob Strickland, attached. 73, --- Zach N0ZGO ----------------------------------------------------------- pacsat-dev mailing list -- pacsat-dev(a)amsat.org <mailto:[email protected]> View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected] To unsubscribe send an email to pacsat-dev-leave(a)amsat.org <mailto:[email protected]> Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org ----------------------------------------------------------- pacsat-dev mailing list -- pacsat-dev(a)amsat.org <mailto:[email protected]> View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected] To unsubscribe send an email to pacsat-dev-leave(a)amsat.org <mailto:[email protected]> Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org

1 0

Re: TMS570 Debug board
by Burns Fisher (AMSAT) 08 Dec '23

08 Dec '23

Ok, Bob. The picture sure looks like there are "holes" there, but you never know. I do think that I asked Zach to put the connector on the bottom so it would line the ribbon cable up correctly with the RTIHU connector. We'll find out. BTW, Newark says they are sending the board from the UK. Hmm. 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software* On Fri, Dec 8, 2023 at 11:00 AM Bob Stricklin via pacsat-dev < pacsat-dev(a)amsat.org> wrote: > Burns, > > I believe he is talking about a 10 pin connector on the bottom left corner > of the photo that is turned down below the board. > He probably did this to make a standard ribbon cable work with female IDC > connectors on each end. > > We can make that change if the boards are shipped. > > It may be that Newark inventory is there because they do not got so much > business on TI product. Normally when an OEM drops a product they pull all > the distributor inventory back. These may be a third party board which is > fine if they have the same processor and code. > > It will be interesting to see if the TI ARM processor TM4C1294NCPDTT3R is > on these boards. If it is and several people working on AMSAT projects need > these boards we probably should buy more. > > The info I have is the design information I showed last night that Zach > shared with me on an AMSAT version of this programming interface board. > > Bob > > > > On Dec 8, 2023, at 9:41 AM, Burns Fisher (AMSAT) via pacsat-dev < > pacsat-dev(a)amsat.org> wrote: > > Thanks, Zach. That might mean that what I ordered is different. See in > the picture, the place where you added the connector is not populated. > (You have to hover over it to get the expanded version in order to see it). > > > https://www.newark.com/texas-instruments/cc-devpack-debug/debugger-devpak-s… > > Well see what happens. Actually do you have a couple of male connectors > that you could send me? That way, I could easily add it in and test the > new board (assuming it comes...maybe you'd better wait until I get a > shipping number :-) ) > > 73, > > Burns Fisher, WB1FJ > *AMSAT(R) Engineering -- Flight Software* > > > On Fri, Dec 8, 2023 at 10:32 AM Zach Metzinger <zmetzing(a)pobox.com> wrote: > >> On 12/8/23 08:07, Burns Fisher (AMSAT) wrote: >> > Note to Pacsat folks: It appears (and Zach can confirm) that Zach must >> > have just ADDED a connector into a DNP space on the board...this is >> > based on the pictures. >> >> Hello Burns and the Pacsat team, >> >> This is not correct; I replace the female 2x5 connector with a male 2x5 >> shrouded/keyed connector. Instructions, already sent to Bob Strickland, >> attached. >> >> 73, >> >> --- Zach >> N0ZGO > > > ----------------------------------------------------------- > > pacsat-dev mailing list -- pacsat-dev(a)amsat.org > View archives of this mailing list at > https://mailman.amsat.org/hyperkitty/list/[email protected] > To unsubscribe send an email to pacsat-dev-leave(a)amsat.org > Manage all of your AMSAT-NA mailing list preferences at > https://mailman.amsat.org > > > > ----------------------------------------------------------- > > pacsat-dev mailing list -- pacsat-dev(a)amsat.org > View archives of this mailing list at > https://mailman.amsat.org/hyperkitty/list/[email protected] > To unsubscribe send an email to pacsat-dev-leave(a)amsat.org > Manage all of your AMSAT-NA mailing list preferences at > https://mailman.amsat.org >

1 0

Re: TMS570 Debug board
by Bob Stricklin 08 Dec '23

08 Dec '23

Burns, I believe he is talking about a 10 pin connector on the bottom left corner of the photo that is turned down below the board. He probably did this to make a standard ribbon cable work with female IDC connectors on each end. We can make that change if the boards are shipped. It may be that Newark inventory is there because they do not got so much business on TI product. Normally when an OEM drops a product they pull all the distributor inventory back. These may be a third party board which is fine if they have the same processor and code. It will be interesting to see if the TI ARM processor TM4C1294NCPDTT3R is on these boards. If it is and several people working on AMSAT projects need these boards we probably should buy more. The info I have is the design information I showed last night that Zach shared with me on an AMSAT version of this programming interface board. Bob On Dec 8, 2023, at 9:41 AM, Burns Fisher (AMSAT) via pacsat-dev <pacsat-dev(a)amsat.org<mailto:[email protected]>> wrote: Thanks, Zach. That might mean that what I ordered is different. See in the picture, the place where you added the connector is not populated. (You have to hover over it to get the expanded version in order to see it). https://www.newark.com/texas-instruments/cc-devpack-debug/debugger-devpak-s… Well see what happens. Actually do you have a couple of male connectors that you could send me? That way, I could easily add it in and test the new board (assuming it comes...maybe you'd better wait until I get a shipping number :-) ) 73, Burns Fisher, WB1FJ AMSAT(R) Engineering -- Flight Software On Fri, Dec 8, 2023 at 10:32 AM Zach Metzinger <zmetzing(a)pobox.com<mailto:[email protected]>> wrote: On 12/8/23 08:07, Burns Fisher (AMSAT) wrote: > Note to Pacsat folks: It appears (and Zach can confirm) that Zach must > have just ADDED a connector into a DNP space on the board...this is > based on the pictures. Hello Burns and the Pacsat team, This is not correct; I replace the female 2x5 connector with a male 2x5 shrouded/keyed connector. Instructions, already sent to Bob Strickland, attached. 73, --- Zach N0ZGO ----------------------------------------------------------- pacsat-dev mailing list -- pacsat-dev(a)amsat.org<mailto:[email protected]> View archives of this mailing list at https://mailman.amsat.org/hyperkitty/list/[email protected] To unsubscribe send an email to pacsat-dev-leave(a)amsat.org<mailto:[email protected]> Manage all of your AMSAT-NA mailing list preferences at https://mailman.amsat.org

1 0

Re: TMS570 Debug board
by Burns Fisher (AMSAT) 08 Dec '23

08 Dec '23

I was just going to use my existing cables to test it. Bob may need those. Not sure what JTAG connector he used on his board. If this actually works, we should order maybe 10. We might need some for Golf too so maybe 20. 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software* On Fri, Dec 8, 2023 at 10:56 AM Zach Metzinger <zmetzing(a)pobox.com> wrote: > On 12/8/23 09:41, Burns Fisher (AMSAT) wrote: > > Thanks, Zach. That might mean that what I ordered is different. See in > > the picture, the place where you added the connector is not populated. > > (You have to hover over it to get the expanded version in order to see > it). > > > > > https://www.newark.com/texas-instruments/cc-devpack-debug/debugger-devpak-s… > > < > https://www.newark.com/texas-instruments/cc-devpack-debug/debugger-devpak-s… > > > > > > Well see what happens. Actually do you have a couple of male connectors > > that you could send me? That way, I could easily add it in and test the > > new board (assuming it comes...maybe you'd better wait until I get a > > shipping number :-) ) > > Ah, yep. It looks like they took that connector off -- which is nice: > now you don't have to unsolder anything! > > I do have a few connectors, but just in case, here's the part # you'll > need to order: FTSH-105-01-L-D-K > > > The ribbon cable will then be FFSD-05-D-06.00-01-N to connect the > RTIHU to the modified CC-DEVPACK-DEBUG. > > --- Zach > N0ZGO > >

1 0

Re: TMS570 Debug board
by Burns Fisher (AMSAT) 08 Dec '23

08 Dec '23

Thanks, Zach. That might mean that what I ordered is different. See in the picture, the place where you added the connector is not populated. (You have to hover over it to get the expanded version in order to see it). https://www.newark.com/texas-instruments/cc-devpack-debug/debugger-devpak-s… Well see what happens. Actually do you have a couple of male connectors that you could send me? That way, I could easily add it in and test the new board (assuming it comes...maybe you'd better wait until I get a shipping number :-) ) 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software* On Fri, Dec 8, 2023 at 10:32 AM Zach Metzinger <zmetzing(a)pobox.com> wrote: > On 12/8/23 08:07, Burns Fisher (AMSAT) wrote: > > Note to Pacsat folks: It appears (and Zach can confirm) that Zach must > > have just ADDED a connector into a DNP space on the board...this is > > based on the pictures. > > Hello Burns and the Pacsat team, > > This is not correct; I replace the female 2x5 connector with a male 2x5 > shrouded/keyed connector. Instructions, already sent to Bob Strickland, > attached. > > 73, > > --- Zach > N0ZGO

1 0

TMS570 Debug board
by Burns Fisher (AMSAT) 08 Dec '23

08 Dec '23

Zach, I happened to notice that Newark still has some of the DEVPACK boards in stock. Now Newark is not the most reliable of sources, but they are cheap. Anyway, to everyone, I ordered two plus a similar one they Newark listed as a replacement. We'll see what happens. Note to Pacsat folks: It appears (and Zach can confirm) that Zach must have just ADDED a connector into a DNP space on the board...this is based on the pictures. 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*

1 0

Pictures of my debug probe
by Burns Fisher (AMSAT) 07 Dec '23

07 Dec '23

The ribbon cable has the same connector on both ends...Zach replaced the connector on the debug board with one like he has on the RT-IHU (or maybe it was even just changing the gender). You can see the number of the big chip on the bottom, but I could not even make out the numbers on the little one with a bright light and mag goggles. 73, Burns Fisher, WB1FJ *AMSAT(R) Engineering -- Flight Software*

1 0

TMS570 JTAG interface
by Corey Minyard 07 Dec '23

07 Dec '23

It looks like the launchpad uses an XDS100v2 chip for going from USB to serial ports and JTAG. TI's web page on it is https://software-dl.ti.com/ccs/esd/documents/xdsdebugprobes/emu_xds100.html The USB device ID would be provided by the XDS100, so as long as you have that chip, it should just work. I've used Olimex before for other things, and that adapter is 55 euro. Anyway, we have options. -corey

1 0

pacsat dev mtg 12/7/2023
by Bill 07 Dec '23

07 Dec '23

pacsat dev mtg 12/7/2023 Thu, Dec 7, 2023 7:00 PM - 9:00 PM (CST) Please join my meeting from your computer, tablet or smartphone. https://meet.goto.com/153619293 You can also dial in using your phone. (For supported devices, tap a one-touch number below to join instantly.) United States: +1 (872) 240-3412 - One-touch: tel:+18722403412,,153619293# Access Code: 153-619-293 Join from a video-conferencing room or system. Dial in or type: 67.217.95.2 or inroomlink.goto.com Meeting ID: 153 619 293 Or dial directly: 153619293(a)67.217.95.2 or 67.217.95.2##153619293 Get the app now and be ready when your first meeting starts: https://meet.goto.com/install

1 0

Re: PCB
by Jim McCullers 06 Dec '23

06 Dec '23

I second Bill, WOWWOW! Picked these up today and everything looks fine so far.

1 0