April 2020 - AMSAT-BB - mailman.amsat.org

M2 LEOpack tuning
by Mark D. Johns 08 Apr '20

08 Apr '20

I’ve had my LEOpack antennas about 8 years, but over the winter my station became almost totally deaf on 2 meters. I took the 2 meter beam down and cleaned up a bunch of corrosion around the coax connector, and that seems to have helped the situation, but... I checked the antenna with my MFJ Antenna Analyzer (which I did not have back when I first assembled these antennas) and find that the 2 meter beam is resonant at about 143.95 MHz — just below the 2 meter ham band. Up at 145.9, where I would LIKE it to be resonant, my SWR is about 2.5:1. Pretty high. Messing with the tuning sliders only made things worse (these adjust impedance and not necessarily resonance), so I’m wondering, has anyone else found it necessary to trim the elements on these? My calculations are that about 1/8” off each end of the DEs would bring it up the 2 MHz needed. Opinions? -- ***Sent from Gmail on iPhone*** Mark D. Johns, Ph.D. K0JM Professor Emeritus of Communication Studies at Luther College, Decorah, Iowa USA Now residing in Minneapolis, Minn. ------------------------------------------------ "Get the facts first. You can distort them later." ---Mark Twain

3 3

sun/moon
by 73 Bob W7LRD 08 Apr '20

08 Apr '20

where is the sun/moon tracker in satpc32? Can't find it. 73 Bob W7LRD

2 1

odd phenomena AO7 ?
by Ron VE8RT 08 Apr '20

08 Apr '20

back in the late 80's and early 90's I'd heard this on the HF sats that downlinked on 10M, but not on 2M. While looking at future satellite plots I had the receiver tuned to the mid band of the AO7 downlink and I'm hearing CW (145.948 MHz). There are no amateur satellites above my horizon, anywhere. It was very clear, sounded like someone listening for their output, long dashes, bursts of CW, pauses, more of the same. I thought that I'd recorded it, but I didn't press the record button long enough and have nothing to show for it. GPredict, at about 21:12 UTC had the azimuth of AO7 at 327 deg with an elevation of -54. It lasted a few minutes and the followed the Doppler correction as shown on GPredict. When I pointed my antenna to the GPredict azimuth for AO7 the signal strength noticeably increased. Does this also happen on 2M? Ron VE8RT -- Ron VE8RT <ve8rt(a)yknwt.ca>

3 4

IC-475H CI-V questions
by Ron VE8RT 07 Apr '20

07 Apr '20

I've recently came into an IC-475H that I'd like to use as the uplink on linear sats. But I'm having some trouble getting the CAT control to work. I'm using grig instead of going in/out of Gpredict just to test the CI-V link. I thought that this should work in grig: grig -m 307 -r /dev/ttyUSB1 -s 1200 -c 14 but it doesn't seem to connect. I have visually verified in the 475 the switch settings for the address and speed, they're set to default $14 1200 baud. With nothing connected the DC voltage on the remote output is about 2.0VDC which agrees with the schematic. I'm hoping that there is something I've overlooked. The interface with grig works with my IC-R7000 grig -m 340 -r /dev/ttyUSB1 -s 1200 -c 08 Ron VE8RT -- Ron VE8RT <ve8rt(a)yknwt.ca>

1 1

A Critique on Operations of the FM Birds
by Brad Smith 07 Apr '20

07 Apr '20

My 2 cents worth of opinion, given free. I own both the Alinco DJ-G7 and Kenwood D72. There is no comparison between the two radios. The Alinco has desense problems, so one still has to use two radios to work full duplex. Where the Alinco shines, is that it can do L/v on AO-92, but still with another radio for down link to hear it best. Save your money for a D710, unless you are looking for L/v! 50 watts?? I think that if you check the specs of the new 9700 radio, it puts out more than 50 watts. Couple that to a 30 db gain yagi antenna any one can "rule the airwaves." Yes, please give us portable and handheld hams a break. But the offenders probably are not on this message board. As portables, we try to do the best we can. I do throw my call out once during most passes that I work, because I know that hams need some of the grids that i work from when I rove. I learned that by Gridmaster. I am happy to give someone a grid by appointment. I began working the FM and linear birds in 2013. It has always been a "good old boys club" on the birds. Guys saying "Hi" to their friends and it isn't going to change. I remember Uncle Frank being the center of attention on each pass and there was a "Breakfast Club." It was fun back then. Yes, the birds were much less busy, but not much has or will change other than the amount of people trying to get into a bird. PO-101 seems to be that way now. Why does one permanent shack station, with high power have to dominate a pass? Especially when a rover is on. Make one contact and let people get the rover. Just because you may not collect grids, a lot of others do. I, personally am unhappy with what I am hearing on the FM birds and it is not the guys saying "Hi" to their friends. There is a lot more going on our there. There are some very poor operators out there and I believe, some jammers with open mics, etc. That part is sad and has gotten worse, lately. Again,just my opinion and thank you for letting me voice it. Brad Smith KC9UQR

1 0

Re: [amsat-bb] FT-736R TAP Board Install
by Mike Lucas 06 Apr '20

06 Apr '20

Good day & hope everyone is doing well. Has anyone done a TAP board installation on their Ft-736R & used it with an SDR as a PAN adapter? If so can you share your experience with it and maybe point me to some installation tips, pix, etc.? It looks like a worthwhile project for not a lot of expense. Regards, Mike N7ASZ

1 0

May QST
by Ray Soifer 06 Apr '20

06 Apr '20

The digital edition of May QST is now available to ARRL members. See pp. 52-53. 73 Ray W2RS

1 0

SatPC32 with the FT-818nd
by Loren M. Lang 06 Apr '20

06 Apr '20

I recently tried using SatPC32 for CAT control of my Yaesu FT-818nd rig for automatic tuning during a pass of the XW-2B linear transponder satellite. The radio appears to be just a minor hardware refresh of the FT-817 and FT-817nd so I have it configured to use Yaesu FT-817 in the radio control settings. My CAT control interface is using a U5 Link which connects to the accessory port on the back of the radio. Inside the box, it is just an FTDI chip. It is set to the baud rate 38400. I have successfully been using this box with both Ham Radio Deluxe and N1MM for various other controls. However, I had an issue with SatPC32 not making all of the correct adjustments. >From what I can tell, it is dropping commands. The radio was only partly configured correctly such as setting the USB/LSB modes on VFOs A/B. It was not adjusting the frequency. I had the CAT delay set to the original value of 70 ms and tried increasing it. At 180 ms, it was still having issues, but I finally bumped it up to 300 ms and the radio started responding correctly. I then saw it tuning both the TX and RX VFOs as needed throughout the pass. However, at this delay, it spends a noticeable amount of time in the TX VFO before it updates the frequency and, if I'm not watching carefully, will press the PTT on only to have it jump to the RX VFO to transmit. It also means more time where I won't be hearing the incoming signal if someone else is talking. Are there any recommendations for improving this situation or could I possibly have a bad (cheap Chinese clone?) FTDI chip that is limiting the rate that commands can be sent? I have not had any issues with HRD or N1MM, but I expect they are sending commands at a lower rate since it's not a constant Doppler shift. Anyone else have a solid FT-817/818 setup? - Loren K7IW

1 0

Re: [amsat-bb] How to Drive SATpc32
by Michael Walker 06 Apr '20

06 Apr '20

I'm sure that someone might be able to share that with you from this list. I'm still hacking away at them and I am amazed that I made so many errors in 3 or 4 entries. Someone might be able to share theirs with you. Mike va3mw On Sun, Apr 5, 2020 at 6:54 PM Ted Krempa <k7trkradio(a)charter.net> wrote: > Nice video, Mike. > > I wish there were something like this to cover the importing/updating/setup > of the sql files. That is where my problems have always been and what > prevents me from using the program. > > 73, Ted > K7TRK > > -----Original Message----- > From: AMSAT-BB [mailto:amsat-bb-bounces@amsat.org] On Behalf Of Michael > Walker via AMSAT-BB > Sent: Sunday, April 5, 2020 11:56 AM > To: AMSAT > Subject: [amsat-bb] How to Drive SATpc32 > > Hi All > > I did this video to help experienced hams but new satellite operators to > navigate SATpc32. > > https://youtu.be/JLdROrcY7fY > > For me, the first weeks week terribly frustrating to get over the hump. > > This assumes your radio and rotator are already connected to SATpc32 but > you have yet to get a quality first QSO. > > Feel free to add useful comments in the video chat. > > Mike va3mw > _______________________________________________ > Sent via AMSAT-BB(a)amsat.org. AMSAT-NA makes this open forum available > to all interested persons worldwide without requiring membership. Opinions > expressed > are solely those of the author, and do not reflect the official views of > AMSAT-NA. > Not an AMSAT-NA member? Join now to support the amateur satellite program! > Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb > >

1 0

How to Drive SATpc32
by Michael Walker 05 Apr '20

05 Apr '20

Hi All I did this video to help experienced hams but new satellite operators to navigate SATpc32. https://youtu.be/JLdROrcY7fY For me, the first weeks week terribly frustrating to get over the hump. This assumes your radio and rotator are already connected to SATpc32 but you have yet to get a quality first QSO. Feel free to add useful comments in the video chat. Mike va3mw

2 1

A Critique on Operations of the FM Birds
by Chris Hoffman 05 Apr '20

05 Apr '20

We all want and need more good operators on the FM Birds, and each pass is a severely-limited resource. Unfortunately, I am constantly bearing witness to operating practices which run counter to these facts. To promote more operators using the birds we have, so that they can give up new grid squares, and perhaps become more active down the road, and in order to build the AMSAT membership I offer the following: FOR *ALL* FM SATELLITE OPERATORS: Please update your personal/favored Best Practices Guide with your reflection upon the following suggestions... 1) *Record your audio for each pass* - If you are running portable: I'm in love with my little Sony voice recorder that has simultaneous audio in and out on 3.5mm jacks. - If you can run 50w, and/or high gain, you have zero excuses not to do so. 1b) When you are recording your passes, please *don't ask for callsign repeats*. - Just be sure the entire callsign was clear for the recording. - That repeat takes up an entire window for a new contact. 2) Keep your contact to *pass*ing *no more than the exchange (e.g. callsign and grid square)* - Even one extra transmission soaks valuable bird time needed for the next contact to start, ad provides no added benefit to the community. - e.g. There is no need to let the distant operator know you sent them a package. 3) *Don't repeat contacts*, even just to say 'hello.' - It soaks an entire contact window for someone else, and that person usually is not on the bird for every pass. - I have seen this, first-hand: hearing a conversation on a satellite crushes new operators (literally and figuratively). They were waiting for a window to make a contact on the only pass of the day, and hearing this provided an excellent excuse for the new operators give up, and abandon sat work entirely because they realize they may never be able to get to the 'level' of someone having that conversation, depriving the rest of us of future new contacts. 4) *Don't use 50w †* - I continually hear big-gun stations wind up crushing less-powerful operators trying to get into the bird -- many of whom are usually equipped with just a handheld and a handheld beam... and many of those are just trying to make their first contact via our 'smart space debris'. - This practice alsso keeps 'honest' 5-watt'ers from being able to score needed Grid Squares as the neelessly-stronger stations carelessly override our signals... [aherm] especially when acting contrary to Suggestion '3'. 5) *Use Full Duplex* - Out of consideration for others, please do not try to make a contact via the bird without a full-duplex radio and the ability to hear others on the satellite. - Good-quailty Full-duplex FM radios are cheap and available online for as little as $100, or new for $250 (DJ-G7). - By hearing your signal on the bird, you will begin to hear and understand that your signal may be stepping on other operators also trying to get in. - As soon as you hear yourself on top someone else, consult Suggestion 4, and make a decision about how needed your contact is. In Summary: *YOU DO NOT OWN THE BIRD* * - *If it's a blank passband... THAT'S A GOOD THING! Every blank second is an opportunity for a new station to make a call, which is what we want. - ASSUME that there is ALWAYS someone new on, usually with just an arrow/elk and their handheld, trying to make their first contact. VUCC wasn't earned in a day, but it shouldn't take 3 passes for one operator to make a single contact. I believe I may be re-sending some variation of this [message] each time I encounter more of the operating practices I've recently observed on AO-91/92 and SO-50 which sparked this Email*. † 47 CFR § 97.313 <https://www.law.cornell.edu/cfr/text/47/97.313> - '...minimum transmitter power necessary' * Flagrancy may earn an edited copy of these suggestions sent directly to you. Repeated Flagrancy may earn a shame-mail to the group. /ch KG6O atsin arrl dot net

1 0

More ancient technology Sat Tracker board and software
by Stephan Greene 05 Apr '20

05 Apr '20

More cleaning shack. Sat Tracker board and software. Looks like parallel printer interface to PC and 8 pin DIN to a G5400/5500 rotator control box. Includes frequency tracker add-on software on 3.5 floppy disk and Instant-Track (DOS) on 5.25 floppy and CD. No capability to check if floppies are readable. InstantTrack will run on a Win10 system using DOSBOX. Email me direct if you want it. All sent as-is. 73 Steve KS1G <callsign> at amsat.org

1 0

Anyone want a Kansas City Tracker manual?
by Stephan Greene 05 Apr '20

05 Apr '20

Found while cleaning out shack. LL Grace KCT v 2.43A instructions, June 2000. Excellent condition. Email me direct your mailing address if you want it. No I can't scan and email it. 73 Steve KS1G

1 0

Kudos: WB4SON and the AMSAT Ambassador Program
by Ev Tupis 04 Apr '20

04 Apr '20

I can't thank AMSAT enough for providing the AMSAT Ambassador program. This morning, the Rochester VHF Group convened it's first "Spring Session" of 2020 ... online! AMSAT Ambassador Bob Beatty, WB4SON kept everyone both interested and engaged. He is an extremely personable, knowledgeable and fluent speaker; an excellent AMSAT resource. His professionalism was evident as he ran two "test flights" with us prior to the live, online meeting. Everything was assured to run smoothly. I strongly endorse the AMSAT Ambassador program and recommend clubs big-and-small take pause to look into it more deeply: https://www.amsat.org/ambassador/ While I'm certain that all AMSAT Ambassadors are well qualified, I can say for certainty that if you are lucky enough to get Bob's schedule to align with your clubs' then you are certain to have a successful event. Yours in the hobby, Ev Tupis, W2EV Chairman, Rochester VHF Group http://www.RVHFG.org Celebrating 71 years as the longest continuously active VHF oriented club in the known universe

2 1

AMSAT Awards during Stay Home orders
by Bruce 04 Apr '20

04 Apr '20

So, you are sitting at home waiting to go back to work. You are working some of the passes of a satellite. Logging as you go. What are you going to do with all those contacts in your log? Easy… You apply for an AMSAT or ARRL award. The ARRL has Worked All States, DXCC and VUCC all with satellite endorsements. AMSAT has the Satellite Communicator Club for working your very first contact on a satellite. The easiest award to apply for. Go directly to the AMSAT Online store and purchase the award. In the comments enter the time/date, satellite and station worked. That’s it. No waiting for QSL cards, no waiting for LoTW confirmation. Then send me an email that you have paid for the award so I know there is one waiting to be processed. AMSAT has a few other awards. The AMSAT Satellite Communications Achievement Award for working 20 different contacts in different US States, VE Call Areas and DXCC entities. Adding 40 more, you earn the AMSAT Sexagesimal Award and adding another 40 earns the AMSAT Century Award. Have you been keeping your log for a long time? You might already qualify for the AMSAT Robert W. Barbee Jr., W4AMI Satellite Operator Achievement Award. This award is for 1,000 contacts with anyone over a satellite. Endorsements for each 1,000 up to 4,000 and a special certificate at 5,000. There is also the South Africa AMSAT Satellite Communications Achievement award. This award is for 25 contacts through a LEO satellite. As we have no HEO satellites at this time and only one GEO satellite you are pretty much good on almost any satellite you work. And the final one, the AMSAT Rover award. A bit much to explain here. You can get information on all the AMSAT Awards at http://www.amsat.org click on Services and click on the word Awards. You can also click on each of the individual awards to get information on each. Submission is easy for the AMSAT awards. Scan your QSL cards or screen shot your LoTW for each contact. Place them in a ZIP file, Word Document, PDF document and email them to kk5do at amsat dot org. I will then take a look at your submission, complete my documentation and email you to go pay for the award/s at the AMSAT online store. Remember, all satellites are COVID-19 free and you should have no hesitation making a contact through one. 73...bruce -- Bruce Paige, KK5DO AMSAT Director Contests and Awards AMSAT Board Member 2016-2020 ARRL Awards Field Checker (WAS, 5BWAS, VUCC), VE Houston AMSAT Net - Wed 0100z on Echolink - Conference *AMSAT* Also live streaming MP3 at http://www.amsatnet.com Podcast at http://www.amsatnet.com/podcast.xml or iTunes Latest satellite news on the ARRL Audio News http://www.arrl.org AMSAT on Twitter http://www.twitter.com/amsat

1 0

PSAT-2/NO-104 status
by Tomáš Urbanec 03 Apr '20

03 Apr '20

Hi all, NO-104/PSAT2 status The 2m/APRS side of the sat is still non operating for the unknown reasons. Any change or any packet heard would be welcomed. The 435MHz side of the sat is still going strong. The PSK31 transponder is operating flawlessly with occasional activity seen over the US. If you are operating through transponder, you are asked to stay within 400-1000Hz of downlink frequency. Lower you can interfere with the tlm beacons and higher you will be wiped off by the SSTV signal. The orbit is elliptical with apogee position period approximately 34 days. The 435.350MHz downlink frequency is temperature dependent a bit so best reception with any kind of SDR, where in waterfall you can see actual downlink freq. The greatest offset is seen after eclipse when sat is coldest. The downlink is operating in Sun only, it switches off entering the eclipse and switches on coming from eclipse or after 30minute timer. The tlm beacons transmit every 4 minutes. The spectrum of the signal is narrow, so in SDR you can use just 2kHz bandwidth gaining SNR. Two minutes after tlm, the SSTV picture is transmitted in 4 minutes intervals also. For reception best bandwidth observed is around 9500Hz. Transmitted pictures are alternating prestored ones and pictures from camera memory stored on orbit. Reception is possible on high passes with good omni antenna using the LNA in the quiet environment. But for the passes till horizon, directional antenna and LNA is needed. We are still looking for any stations capable of regular downlink receptions with position between 40deg South and 40deg North. If you can make the receptions available in IQ format it would be greatly welcomed. Station capable of uplink in 29MHz to sat can be selected as commanding station and then can acquire pictures in real time or store them in sequence. So you can get pictures of your side of the globe, just contact us. Further info and contacts can be found at https://github.com/alpov/PSAT-2/blob/master/README.md Best regards Tomas OK2PNQ

1 0

ISS Operating Schedule
by John Lutz 03 Apr '20

03 Apr '20

Does anyone know where information regarding the operating schedule for the ISS crew can be found? Regards, John, N9JL Sent from Yahoo Mail on Android

3 2

Low-Power FM (broadcast band) Transmitter?
by Scott 03 Apr '20

03 Apr '20

I hope the group doesn't mind a non-ham question since we're all trying to help our communities in this difficult time. Can anyone recommend a low-power transmitter for broadcast on the commercial FM radio band? An LPFM license can be acquired asap, but the first order of business is finding some hardware. As you can imagine, church gatherings are out of the question so I've been asked to see if I can locate a "drive-in theater" type transmitter for short-range broadcasting to car radios. Interested in commercial products only; thanks but not something I want to build & be responsible for maintaining. Thanks very much a good wishes to all. -Scott, K4KDR

6 8

Yaesu G-5500 question
by Bob Hammond 02 Apr '20

02 Apr '20

I have my M2 LEO antennas plus a WiMo 23cm helical antenna end-mounted on a fiberglass boom with the G-5500. I also placed a counterbalance lead weight opposite the antennas. I think I've asked this question before and if so I'm asking it again because, well, I CRS: How many of you with similar antennas and a G-5500 have NOT used a counterbalance? Any issues? Bob W7OTJ

5 5

Question on 23cm WiMo Helix
by Thomas Schaefer 02 Apr '20

02 Apr '20

Reading the prior posts about the counterbalance, made me think again about adding the 23 cm helix antenna to my sat beams before they go up, but I wanted to check my thinking on this… There appears to be only one L band satellite, AO-92. That is an uplink. Given that, I obviously have no need for a preamp. But I also believe that I need not worry too much about using anything better than LMR-400. In checking the Times Microwave loss calculator, using LMR400 over a 50 foot run would lose 2.6 dB. Using LMR-600, would lose 1.7 dB. 7/8” hardline would be .8 dB. But given that the Helix has 13 dBd, that is over 100 watts at the antenna. Plenty AO-92. So while cable loss seems academic, are there any satellites in the works accessible from the US with an L band downlink? If not, it appears LMR-400 is just fine (even with a short loop of LMR-400 UF at the top for the rotor). Thanks, Tom Schaefer, NY4I Blog: www.ny4i.com Madeira Beach, FL (Grid: EL87ot)

3 2

FoxDelta trackers
by James Brown 02 Apr '20

02 Apr '20

Thanks Gang Both Fox Delta trackers are committed! Jim KI6WJ

1 0

Re: [amsat-bb] Yaesu G-5500 Question
by MICHAEL WILLIAMS 02 Apr '20

02 Apr '20

My thinking has been to put it out of balance, especially with the light weight satellite antennas we use. In a perfectly balanced system, the wind will work the gearing back and forth. In an unbalanced system, the gears will stay meshed in one direction not working the internal parts when the antennas are moving or are at rest. It's difficult to balance a system when coax and preamps added to the rear. It's also good to have the least wind resistance when SatPC32 returns antennas to the rest position The Yaesu elevation rotors are pretty tough. I used an Alliance U-110 for years with no problems. Talk about out of balance, check my qrz page. Good luck with this. It has been an interesting subject. 73, Mike (K9QHO)

1 0

Yaesu G-5500 question
by Roy Dean 02 Apr '20

02 Apr '20

For what it's worth, I've been using a (prior to me owning it) well used G5400 for the past year with end mounted M2 Leo-Pack yagis..... with no problems at all. My rotator is low enough that "mid mounting" the array (on a fiberglass boom) is not possible, and counterweighting would likely involve a large weight due to the lack of moment arm length available off the back of the array. If/when it fails, I'll be sure to report my findings to this group. --Roy K3RLD

1 0

Test - Please ignore
by Ronald Parsons 02 Apr '20

02 Apr '20

Uyugg ii ikbkjkj hkj bk kkjkhk kkjk vjhv jhbjhb bkb bk jbj hb N3GS 624 652 K9UO 550 565 KK4YEL 413 504 jtff uyuyg ugg

1 0

Garmin ETREX 10 GPS
by alex weimer 02 Apr '20

02 Apr '20

Thanks to all who answered my request. I now have the info I needed .. Looks like it's the way to go for me . Thank you Paul and Patrick

1 0

Re: [amsat-bb] Yaesu G-5500 question
by Bob Hammond 02 Apr '20

02 Apr '20

Thanks for the quick replies M5ET, NR0T, and VE3NXK. The M2 LEO antennas are designed to be end-mounted and M2 has no idea how they'll perform if mid-mounted as they aren't designed for that. Hence, my counterbalance scheme. Bob W7OTJ On Thu, Apr 2, 2020 at 8:01 AM Bill Booth <ve3nxk(a)gmail.com> wrote: > > How many of you with similar antennas and a G-5500 have NOT used a > > counterbalance? > > I did not balance mine in the current install. I did move the mounting > brackets > on the boom when I had the A40 dish on the main boom to help with balance. > > Attached pic of current setup. > > > > -- > Bill Booth VE3NXK > Sundridge ON, Canada > 79.23.37 W x 45.46.18 N > FN05ns > > Visit my weather WebCam at http://www.almaguin.com/wxcurrent/weather.html > > Organ and Tissue Donation - The Gift of Life > Talk to your family. Your decision can make a difference. >

2 1

Fwd: iPhone Program
by Mark L. Hammond 02 Apr '20

02 Apr '20

For ease of use and setup (just add the satellites you want), I find SatSat to be perfect for what I want to do; including a nice feature to add a calendar reminder with notification! Easy to see passes for the next week, etc. Try a few---use what works for you! ;) Mark N8MH On Thu, Apr 2, 2020 at 9:53 AM BRAD SMITH via AMSAT-BB <amsat-bb(a)amsat.org> wrote: > I use the HamSat app from the App Store. It is so easy. I have tried > others and not been satisfied. Brad KC9UQR > > Sent from Brad’s iPad > _______________________________________________ > Sent via AMSAT-BB(a)amsat.org. AMSAT-NA makes this open forum available > to all interested persons worldwide without requiring membership. Opinions > expressed > are solely those of the author, and do not reflect the official views of > AMSAT-NA. > Not an AMSAT-NA member? Join now to support the amateur satellite program! > Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb > -- Mark L. Hammond [N8MH] -- Mark L. Hammond [N8MH]

2 1

iPhone Program
by BRAD SMITH 02 Apr '20

02 Apr '20

I use the HamSat app from the App Store. It is so easy. I have tried others and not been satisfied. Brad KC9UQR Sent from Brad’s iPad

1 0

Re: [amsat-bb] Satelitte Rig, IC-7900 Pros & Cons
by Yono Adisoemarta 02 Apr '20

02 Apr '20

Coming from Yaesu FT-847 and Kenwood TS-2000, I like my IC-9700 very much. 73 de Yono YD0NXX Sent from my iPhone > On Mar 30, 2020, at 4:58 AM, ke4kol via AMSAT-BB <amsat-bb(a)amsat.org> wrote: >

2 1

Satelitte Rig, IC-7900 Pros & Cons
by ke4kol 02 Apr '20

02 Apr '20

Thinking about updating my sat station. Any and all suggestions appreciated. Thaks,Jim Ke4kol

2 2

Re: [amsat-bb] I phone
by Pedro Converso 02 Apr '20

02 Apr '20

On Iphone try http://amsat.org.ar/pass also shows freqs+Doppler. Once started via Inet could run without connection. 73, lu7abf, Pedro

2 1

I phone
by 73 Bob W7LRD 02 Apr '20

02 Apr '20

Hi all- What is good app for satellite tracking for a i phone? 73 Bob W7LRD

3 2

Re: [amsat-bb] VUCC Standings formatting
by Matthew Chambers 02 Apr '20

02 Apr '20

That might be a problem as my email client doesn't have a plain text mode, all emails are HTML with no user changeable settings. I could make all my emails plain text but then it would be server wide for me and anyone else on the domain. And it would wipe out everyone's signature files which would have to be remade in plain text. I just wonder why the email list can't grow with the rest of the internet? Matthew Chambers, CBT, NR0Q Owner/Engineer *M Chambers Communications Engineering LLC* PO BOX 855, Moberly, MO 65270 Mobile (660)415-5620 www.mchambersradio.com On Wed, Apr 1, 2020 at 2:02 PM Mark D. Johns <mjohns+K0JM(a)luther.edu> wrote: > The reflector will not take attachments. But do make sure you set the > email client into "Plain text" mode before you put the data into it. > -- > Mark D. Johns, KØJM > AMSAT Ambassador & News Service Editor > Brooklyn Park, MN USA EN35hd > ----------------------------------------------- > "Heaven goes by favor; if it went by merit, > you would stay out and your dog would go in." > ---Mark Twain > > On Wed, Apr 1, 2020 at 1:41 PM Matthew Chambers via AMSAT-BB > <amsat-bb(a)amsat.org> wrote: > > > > Maybe type it up in a word processor in a table and copy that to your > email > > client? Another idea and this is what my local club does for anything > that > > we want "pretty" formatting on something. Is attach it as a PDF to the > > email and have a minimal blurb that says go read the attached PDF. > > > > Not sure if PDF's would make it across the email reflector, might be a > sign > > that it's started falling behind with the current state of tech. This is > > the only one that I belong to that blows up on embedded HTML and images. > > Most have moved to Groups.IO. > > > > Matthew Chambers, CBT, NR0Q > > Owner/Engineer > > *M Chambers Communications Engineering LLC* > > PO BOX 855, Moberly, MO 65270 > > Mobile (660)415-5620 > > www.mchambersradio.com > > > > > > > > On Wed, Apr 1, 2020 at 10:46 AM Ronald Parsons via AMSAT-BB < > > amsat-bb(a)amsat.org> wrote: > > > > > I'm sorry about the formatting of the standings. I've been searching > for > > > the > > > magic bullet to list columns of data neatly, but the trial this month > > > turned > > > out really bad. If anyone knows the secret, please let me know, > > > > > > Ron W5RKN > > > > > > _______________________________________________ > > > Sent via AMSAT-BB(a)amsat.org. AMSAT-NA makes this open forum available > > > to all interested persons worldwide without requiring membership. > Opinions > > > expressed > > > are solely those of the author, and do not reflect the official views > of > > > AMSAT-NA. > > > Not an AMSAT-NA member? Join now to support the amateur satellite > program! > > > Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb > > > > > _______________________________________________ > > Sent via AMSAT-BB(a)amsat.org. AMSAT-NA makes this open forum available > > to all interested persons worldwide without requiring membership. > Opinions expressed > > are solely those of the author, and do not reflect the official views of > AMSAT-NA. > > Not an AMSAT-NA member? Join now to support the amateur satellite > program! > > Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb >

3 2

VE8RT on AO91 earlier today
by Ron VE8RT 02 Apr '20

02 Apr '20

No it wasn't an April fools day prank, I was on AO91 for a few minutes (before the footprint was too far north) and worked a few stations. It was to be a demonstration of amateur satellite communications for a Canadian Broadcasting Corp locally produced program. Thanks to all who were on. As the antenna, radio, and log keeping were too much of a challenge outdoors (temperature was about -18C or 0F with a windchill around -27C) I used an old recorder for logging. For the most part it worked well, there is at least one call sign I'm having trouble picking out. I've had some help improving the quality, but if someone wanted a copy of the MP3 file to try their luck at getting more out of it I'll send them the file. Its just over 5 min long. Ron VE8RT in DP22 -- Ron VE8RT <ve8rt(a)yknwt.ca>

1 0

Test - Please ignore
by Ronald Parsons 02 Apr '20

02 Apr '20

QWERTYUIOPASDFGHJKLZXCVBNMqwertyuiopasdfghjklzxcvbnm 1234567890 1234567890 12345 67890 QWERTYUIOPASDFGHJKLZXCVBNMqwertyuiopasdfghjklzxcvbnm 1234567890 1234567890 12345 67890 QWERTYUIOPASDFGHJKLZXCVBNMqwertyuiopasdfghjklzxcvbnm 1234567890 1234567890 12345 67890 QWERTYUIOPASDFGHJKLZXCVBNMqwertyuiopasdfghjklzxcvbnm 1234567890 1234567890 12345 67890 A B C D . A B C D . A B C D . A B C D .

1 0

rotator controllers available
by James Brown 02 Apr '20

02 Apr '20

I have two Fox Delta ST-2 rotator interfaces avilable. These are good working units and be great for new station set ups. I ran a G5500 rotor and satpc32 with one. The other is new spare. Google Fox Delta for details. Jim KI6WJ

1 0

Garmin ETREX10 maidenhead grids ??
by alex weimer 02 Apr '20

02 Apr '20

Does anyone know if the Garmin Etrex10 GPS has Maidenhead grids built in ? I cannot find any info and when I call Garmin the people I talk do have no idea.. Thanks JACK KC7MG

5 8

AO-92 in L/v at 0157z for 24 hours 1 April 2020
by Mark L. Hammond 02 Apr '20

02 Apr '20

No foolin'! 73, Mark L. Hammond [N8MH]

3 2

M-2 SAT Pack #1
by Gerald Witalec 01 Apr '20

01 Apr '20

Has anyone used this eggbeater antenna from M-2 company with great results to track the SATS? Jerry...W8RQM

3 2

Tab Delimited Test
by Roy Dean 01 Apr '20

01 Apr '20

W4ZXT 150 202 K5ZM 135 179 WD9EWK 148 164 N4QX 125 150 I suspect that this wont work because gmail is not allowing me to insert tab delimited data. It's inserting it as space delimited. :( --Roy K3RLD

1 0

Test - ignore
by Ronald Parsons 01 Apr '20

01 Apr '20

Now is the time for . Title ABC DEF _____ ______ _____ KLM 123 566 NOP 987 6542 . all good men. Sig

1 0

VUCC Standings formatting
by Ronald Parsons 01 Apr '20

01 Apr '20

I'm sorry about the formatting of the standings. I've been searching for the magic bullet to list columns of data neatly, but the trial this month turned out really bad. If anyone knows the secret, please let me know, Ron W5RKN

2 1

VUCC Standings for April 2020
by Ronald Parsons 01 Apr '20

01 Apr '20

VUCC Awards-Endorsements for April 2020 Happy April Fools Day. Happy Birthday to me! A lot of roves are being canceled as travel is more difficult. Here are the endorsements and new VUCC Satellite Awards issued by the ARRL for the period March 1, 2020 through April 1, 2020. Congratulations to all those who made the list this month! CALL Mar Apr N3GS 624 652 K9UO 550 565 KK4YEL 413 504 G0ABI 453 454 KB2YSI 101 450 AD0HJ 405 425 N7EGY 351 405 KC9VGG 228 310 N9FN 207 303 PT9BM 225 255 KC9UQR 240 252 WA9JBQ 175 225 W4ZXT 150 202 K5ZM 135 179 WD9EWK (DM41) 148 164 WD9EWK (DM22) 131 150 N4QX 125 138 XE2YWH 102 137 EA2AA 101 125 IZ1ERR New 112 N7JY New 106 KE4BKL New 101 AA7WB New 100 DP0GVN New 100 If you find errors or omissions. please contact me off-list at <mycall>@<mycall>.com and I'll revise the announcement. This list was developed by comparing the ARRL .pdf listings for the two months. It's a visual comparison so omissions are possible. Apologies if your call was not mentioned. Thanks to all those who are roving to grids that are rarely on the birds. They are doing much of the work! Ron W5RKN

1 0