- AMSAT-BB - mailman.amsat.org

TO5M St. Pierre & Miquelon logs - recordings needed
by Schuette, Martin A 24 Aug '19

24 Aug '19

Hello sat ops, I've been helping Chris VO1IDX figure out his logs for his activation of St. Pierre & Miquelon. The currently entered logs are online at https://clublog.org/charts/?c=to5m Sadly Chris had some issues with his audio recorder while on, and also after getting back from, the island. So anyways, if you had a QSO with TO5M on SO-50, AO-85, AO-91, or AO-92, and your callsign is not listed in the log, please shoot VO1IDX an email. If you have a recording of any passes of these birds between August 13th and August 18th, where St. Pierre would have been in the footprint , shoot us both an email. 73, Marty Schuette N9EAT

1 0

ADIF to gridmap program
by jeff griffin 24 Aug '19

24 Aug '19

I've decided to try and work on my Grids worked from this location. To do so I'm going to have to deal with the FM birds. I'm trying to keep this as painless as possible so I'm looking for an ADIF to gridsquare map program. A program that will input an ADIF file and map out what grids are needed and what are already worked graphically. A quick google shows there are several available, what one's are recommended ? Thanks for any useful input. 73 Jeff kb2m

3 2

PSAT2 Anomaly?
by Robert Bruninga 23 Aug '19

23 Aug '19

The usual PSAT2 downlink stopped after 0809z today in a pass over SE USA. Ground Stations are fine because its sister, USNAP1, is still downlinking via the usual ground stations. Both downlinks visible on http://aprs.org/sats.html A cessation of our Amateur packet telemetry design has never happened in 18 years in space over 6 successful spacecraft other than the occasional low power crash which is fixed after the next eclipse on the next pass or so. But never a complete cessation. Since the UHF side is independent, we welcome folks to listen to the UHF downlink 435.350 +/- Doppler and verify if that is working. Remember, it must be in daylight for the SSTV downlink to be on. Fortunately we do have one report of an SSTV image at 1340z from Gustave LW2DTZ. If we have another confirmation that UHF has been heard, then we can rule out a possible collision with space debris. (we get notificaitons of near conjunctions passing within 500m about every day or so, but after 18 years we have come to ignore them. Maybe this one hit? And it was working so well! Bob, WB4APR

3 4

Echostar 9 test cards
by KC9SGV 23 Aug '19

23 Aug '19

Some Echostar 9, 12 GHz TV channels and test cards are shown here. Scroll down. https://www.lyngsat.com/EchoStar-9-Galaxy-23.html KC9SGV Sent from my iPad

10 11

Re: [amsat-bb] G-5500 az rotor failure
by k.swaggart＠charter.net 23 Aug '19

23 Aug '19

The problem turned out to be a loose setscrew at the motor. Easy fix, but took about four hours to reassemble the rotor so the limit switch was tripped correctly and then get the antennas reattached. Anyway, back in business. I took quite a few photos of the az rotor disassembly and I'll add them to my G5500 page within the next few days: http://www.ocrg.org/W7KKE/rotor/rotor.html 73, Ken, W7KKE From: k.swaggart(a)charter.net <k.swaggart(a)charter.net> Sent: Friday, August 23, 2019 10:39 To: AMSAT-BB (amsat-bb(a)amsat.org) <amsat-bb(a)amsat.org> Subject: G-5500 az rotor failure This morning I found my G-5500 will not move left or right. Not even a wiggle. Took some measurements and the wiring appears to be intact but I don't understand the 40 Vac readings when the rotor is connected to the control box. Here are my readings taken at the control box end of the wiring: Rotor connected to control box: Common (pin 6) to Left (pin 4) Press Left: 28 Vac Right: 40 Vac Common (pin 6) to Right (pin 5) Press Left: 40 Vac Right: 28 Vac Rotor disconnected. Measuring control box terminals: Pin 6 to 4 Press Left: 29.5 Vac Press right: 0 Pin 6 to 5 Press Left: 0 Press Right: 29.5 Vac Measuring rotor cable at control box, disconnected from box: 6 (brown) to 4 (blue) 5.3 Ohms 6 (brown) to 5 (orange) 5.3 Ohms 4 (blue) to 5 (orange) 8.9 Ohms Any suggestions before I pull the rotor off the mast? 73, Ken, W7KKE

2 1

Re: [amsat-bb] Echostar 9 test cards
by Edward R Cole 23 Aug '19

23 Aug '19

Bob and all: A good source of info on using ku-band TVRO LNA's for ham use on 10-GHz is from several eme hams who use them. My guess the LNA's are broadbanded that requires no modification of tuned input ckts to operate at 10-GHz. Since you application may be on the original sat-TV band frequency they may perform optimally. I am not sure if they also downconvert to an IF. My experience was with C-band sat-TV which used LNB's to amplify 3400-3750 MHz and downconvert to 950-1400 MHz. GL with exploring ham use of Echostar-9. I have plans to build a 10-MHz eme station using my 1.8m surplus off-set feed sat-TV dish (used starting in 1996 in AK on Direct-TV). 73, Ed - KL7UW Not QRV for Leo sats Date: Fri, 23 Aug 2019 09:31:08 -0400 From: Robert Bruninga <bruninga(a)usna.edu> To: AMSAT-BB <AMSAT-BB(a)amsat.org> Subject: Re: [amsat-bb] Echostar 9 test cards Message-ID: <df6594fa700d9fd2b5645815a35c16f7(a)mail.gmail.com> Content-Type: text/plain; charset="UTF-8" I actually am excited about the prospect of using LNA's from all these throw-away Dish network dishes for something. It's a great educational opportunity. I am happy to tune in anything that is interesting from a technical perspective and I really love making stuff from cast-off stuff. Bob, WB4APR 73, Ed - KL7UW http://www.kl7uw.com Dubus-NA Business mail: dubususa(a)gmail.com

1 0

G-5500 az rotor failure
by k.swaggart＠charter.net 23 Aug '19

23 Aug '19

This morning I found my G-5500 will not move left or right. Not even a wiggle. Took some measurements and the wiring appears to be intact but I don't understand the 40 Vac readings when the rotor is connected to the control box. Here are my readings taken at the control box end of the wiring: Rotor connected to control box: Common (pin 6) to Left (pin 4) Press Left: 28 Vac Right: 40 Vac Common (pin 6) to Right (pin 5) Press Left: 40 Vac Right: 28 Vac Rotor disconnected. Measuring control box terminals: Pin 6 to 4 Press Left: 29.5 Vac Press right: 0 Pin 6 to 5 Press Left: 0 Press Right: 29.5 Vac Measuring rotor cable at control box, disconnected from box: 6 (brown) to 4 (blue) 5.3 Ohms 6 (brown) to 5 (orange) 5.3 Ohms 4 (blue) to 5 (orange) 8.9 Ohms Any suggestions before I pull the rotor off the mast? 73, Ken, W7KKE

2 1

Old AMSAT FTP site.
by vk2tfg 23 Aug '19

23 Aug '19

Greetings all, Does anybody know if there is a way to download the software & data that was at https://www.amsat.org/amsat-new/tools/ftpsoft.php ? I am after supporting info that was with some packages in particular YACER 1.03 and ConvKeps. Any info that is available would be gratefully accepted. 73 de Geoff vk2tfg.

2 2

MSPE Error NO-5
by Vincenzo Mone 23 Aug '19

23 Aug '19

Hi Folks, I am using MSPE from the Wisp package to work on the Falconsat-3 Satellite. I am noticing from a while that every time I send the Dir request to the satellite, I get from it The ERROR NO-5. Did not understood which is the problem. Any clue ho to solve the problem? Any help will be really appreciated. 73 de Enzo IK8OZV EasyLog 5 BetaTester EasyLog PDA BetaTester WinBollet BetaTester D.C.I. CheckPoint Regione Campania Skype: ik8ozv8520 ********************************* ****** GSM +39 328 7110193 ****** ***** SMS +39 328 7110193 ***** *********************************

2 1

Dish size required for Echostar 9
by KC9SGV 23 Aug '19

23 Aug '19

Looks like a smaller dish is required for Echostar 9 reception on the Ku band. http://satstar.net/beams/echo9galaxy23_ku.html Bernard, KC9SGV Sent from my iPad

1 0